Introduction
Thank you very much for purchasing our ROBORE SF20 Foldable Treadmill. Please read this instruction carefully before use and keep it in a proper place for future reference.
Note: Our products are constantly updated and are subject to change without notice. Thank you for your understanding.
1. About the Product
The ROBORE SF20 is a multi-function household electric treadmill designed for effective cardio training.
Product Components Overview
The treadmill consists of several key parts:
- Display Window: Shows exercise data.
- Safety Lock: Essential safety feature to stop the treadmill.
- Motor Top Cap: Covers the motor assembly.
- Incline Adjustment: Mechanism to change the running belt's angle.
- Running Belt: The surface for walking or running.
- Left/Right Rear Caps: Protective covers at the rear of the treadmill.
- Left/Right Bolts: Fasteners for various parts.
(Refer to the diagram on page 2 of the PDF manual for a visual representation of these components.)
2. Safety Precautions and Warning Instructions
Caution
To avoid any injuries, please read this manual carefully before using the treadmill.
Safety Notice
Always place the machine on flat, stable ground. It is unsuitable for use in the following locations:
- Outdoors (designed for indoor use only).
- On slanted ground or balconies.
- In direct sunlight or near heaters.
- In excessively noisy areas.
Additional safety guidelines:
- Errors may occur if the power supply is unstable.
- Do not share the same electrical socket with other high-power appliances like computers or air conditioners.
- Wear appropriate sports shoes when using the machine.
- Increase or decrease speed slowly and gradually.
- Exercise caution with children or other objects when folding and unfolding the machine.
- Keep the machine away from wet objects to prevent water damage.
(Refer to the safety warning icons on page 4 of the PDF manual for visual guidance.)
Caution During Use
- Consult your doctor or coach if you feel unwell before using.
- The manufacturer is not responsible for injuries caused by improper use.
- Always switch off all functions and unplug the machine after use.
- Unplug the machine before any movement or part changes.
- Children, elderly individuals, and pregnant women are prohibited from using the machine.
- Patients should consult a doctor before use.
- Prevent water from dripping onto the machine, especially the motor, power line, and plug.
- Avoid wearing long or unsuitable dresses that could get caught in the machine.
- Do not use the machine in enclosed, unventilated, or flammable areas.
- Do not place any objects on the machine.
- Keep the plug away from heated surfaces or fire sources.
- Do not stand directly on the belt when starting the machine.
- Do not disassemble the machine without professional supervision.
- Ensure the running belt is properly fastened before use.
3. Assembly Instruction
The following steps apply to all models:
-
Step 1: Unpacking and Initial Setup
Open the package, remove all assembly materials from the box, and carefully lay the main part of the treadmill on the ground. Expand the fixed column to its upright position.
The ROBORE SF20 treadmill in its folded and unfolded states, demonstrating ease of setup and storage. (Refer to Figure 1 and Figure 2 on page 5 of the PDF manual for visual guidance on unpacking and expanding the fixed column.)
-
Step 2: Securing the Column and Display Window
- Use Knob M8*50 to screw and secure the lower part of the column.
- Use Knob M8*37 to screw and secure the upper part of the column to fix the display window.
(Refer to Figure 3 on page 5 of the PDF manual for visual guidance on securing the column and display window.)
-
Step 3: Attaching the Safety Lock and Adjusting for Stability
- Attach the red safety lock switch. Failure to do so will result in an E7 error.
- While exercising, attach the safety clip to your clothing near the waistline. In case of any complications, a strong tug on the safety lanyard will immediately stop the running belt.
(Refer to Figure 4 on page 5 of the PDF manual for visual guidance on attaching the safety lock.)
Attention: Treadmill Stability
If the treadmill wobbles during use, adjust the two adjustable knobs located under the treadmill base until it is stable.
(Refer to Figure 5 on page 5 of the PDF manual for visual guidance on adjusting the stability knobs.)
4. Operating Instructions
Window Display
- Time: Displays running time in manual mode or countdown in program mode.
- Speed: Displays the current running speed.
- Distance: Displays cumulative distance in manual mode or countdown in program mode.
- Calorie: Displays total calories burned in manual mode or countdown in program mode.
Keypress Functions
- ▶ (Start): The machine will start at 1 KM/H after 3 seconds.
- ■ (Stop): The speed will gradually decrease until it stops at 0.
- + (Speed+): Increases the running speed.
- - (Speed-): Decreases the running speed.
- 3/6 (Fast Adjustment): When the machine starts, press to switch speed to 3 KM/H or 6 KM/H.
- P/M (Program/Mode): In standby mode, press this button to cycle through manual mode and automatic programs P1-P12. Manual mode is the default operation.
Countdown Function (P/M Button)
In standby mode, press the P/M button again to access the countdown function with three modes: Time, Distance, and Calorie.
- Step 1: In standby mode, press the P/M key to enter the three countdown modes. The indicator light for the current mode will illuminate. Select your desired mode. Use the + and - keys to increase or decrease the countdown value.
- Step 2: After setting the countdown value, press the ▶ key to start.
Pre-set Programs (P1-P12)
The treadmill offers 12 pre-set programs (P1-P12) with varying speed profiles over 20 time periods. Speeds are in km/h.
| No. | Parameter | Time Periods (1-20) | |||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | ||
| P01 | Speed | 2 | 3 | 3 | 4 | 5 | 3 | 4 | 5 | 5 | 3 | 4 | 5 | 4 | 4 | 4 | 2 | 3 | 3 | 5 | 3 |
| P02 | Speed | 2 | 4 | 4 | 5 | 6 | 4 | 6 | 6 | 6 | 4 | 5 | 6 | 4 | 4 | 4 | 2 | 2 | 5 | 4 | 1 |
| P03 | Speed | 2 | 4 | 4 | 6 | 6 | 4 | 7 | 7 | 7 | 4 | 7 | 7 | 4 | 4 | 4 | 2 | 4 | 5 | 3 | 2 |
| P04 | Speed | 3 | 5 | 5 | 6 | 7 | 7 | 5 | 7 | 8 | 8 | 5 | 9 | 5 | 5 | 6 | 6 | 4 | 4 | 4 | 3 |
| P05 | Speed | 2 | 4 | 4 | 5 | 6 | 7 | 7 | 5 | 6 | 7 | 8 | 8 | 5 | 4 | 3 | 3 | 6 | 5 | 4 | 2 |
| P06 | Speed | 2 | 4 | 3 | 4 | 5 | 4 | 8 | 7 | 5 | 7 | 8 | 3 | 6 | 4 | 4 | 2 | 5 | 4 | 3 | 2 |
| P07 | Speed | 2 | 3 | 3 | 3 | 4 | 5 | 3 | 4 | 5 | 3 | 4 | 5 | 3 | 3 | 3 | 6 | 6 | 5 | 3 | 3 |
| P08 | Speed | 2 | 3 | 3 | 6 | 7 | 7 | 4 | 6 | 7 | 4 | 6 | 7 | 4 | 4 | 4 | 2 | 3 | 4 | 4 | 2 |
| P09 | Speed | 2 | 4 | 4 | 7 | 7 | 4 | 7 | 8 | 4 | 8 | 9 | 9 | 4 | 4 | 4 | 5 | 6 | 3 | 3 | 2 |
| P10 | Speed | 2 | 4 | 5 | 6 | 7 | 5 | 4 | 6 | 8 | 8 | 6 | 6 | 5 | 4 | 4 | 2 | 4 | 4 | 3 | 3 |
| P11 | Speed | 3 | 4 | 5 | 9 | 5 | 9 | 5 | 5 | 9 | 5 | 5 | 5 | 5 | 9 | 9 | 8 | 7 | 6 | 3 | |
| P12 | Speed | 2 | 5 | 8 | 10 | 7 | 7 | 10 | 10 | 7 | 7 | 10 | 10 | 6 | 6 | 9 | 9 | 5 | 5 | 4 | 3 |
5. Exercise Suggestions and Guidelines
Warm-up
Perform 5 to 10 minutes of warm-up exercises before each use of the machine.
Breathing
Maintain coordinated breathing during exercise. If your breathing becomes too fast, stop the exercise immediately.
Frequency
Allow 48 hours of rest for the same muscle group between training sessions. Train each muscle group every other day.
Load
The intensity of your training should be determined by your individual physical condition. Follow a principle of gradual load increase. Initial muscle soreness is normal and will diminish as training continues.
Diet
To protect your digestive system, exercise one hour after meals. After training, wait at least half an hour before eating. Drink less water during exercise, and avoid drinking large quantities of water to prevent strain on your heart and kidneys.
Stretching Exercise
Always stretch before and after your workout. Warm muscles are easier to stretch. After a 5-10 minute warm-up, perform the following five stretches, holding each for 10 seconds or more, and repeating at the end of your workout:
- Downward Stretching: Slightly bend your knees, slowly bend down, relax your back and shoulders, and reach your hands towards your toes. Hold for 10-15 seconds, then relax and repeat 3 times.
- Hamstring Stretching: Sit on a clean cushion, straighten one leg, and bend the other leg, keeping it close to the inner thigh of the straightened leg. Try to touch the toes of the straightened leg with your hands. Hold for 10-15 seconds, then relax and repeat 3 times for each leg.
- Calf and Heel Tendon Stretching: Stand with both hands on a wall or table, with one foot behind the other. Keep your back leg straight and your heel on the ground. Lean towards the wall or table. Hold for 10-15 seconds, then relax and repeat 3 times for each leg.
- Quadriceps (Head Muscle) Stretching: Hold your balance with your right hand on a wall or table. Extend your left hand backward, grasp your left ankle, and gently pull it up towards your hip until you feel tension in the front of your thigh. Hold for about 10-15 seconds, then relax and repeat 3 times for each leg.
- Sartorius Muscle (Inner Thigh) Stretching: Sit with your feet facing each other, knees bent outwards. Grasp your feet with both hands and pull them towards your body. Hold for 10-15 seconds, then relax and repeat 3 times.
(Refer to the stretching exercise diagrams (Figure 1-5) on page 8 of the PDF manual for visual guidance.)
6. Daily Maintenance
1. Elastic Adjustment of Running Belt
The running belt's tension is pre-adjusted at the factory. However, after some use, the belt may loosen, causing a slipping phenomenon during normal operation. To adjust, turn the running belt adjusting bolts (located at the rear of the treadmill) left and right synchronously by half a circle clockwise.
Note: Do not overtighten the running belt, as this can accelerate its aging, increase motor load, and shorten the bearing's service life. The belt should be tight enough to prevent slipping during normal use.
2. Deviation Adjustment of Running Belt
Running belt deviation can occur due to:
- Unstable placement of the main unit.
- User's feet not being centered on the running belt during exercise.
- Uneven force applied by the user's feet.
Deviation caused by human factors often self-corrects after several minutes of no-load operation. For persistent deviation, manual adjustment of the belt adjusting screw is required.
Procedure: Stand at the rear of the treadmill, facing the display. Use the provided hex key to make adjustments on the rear bolts.
- If the belt is off-center to the LEFT: Turn the left adjusting bolt ¼ turn clockwise, or the right adjusting bolt ¼ turn counterclockwise. This moves the running belt to the right.
- If the belt is off-center to the RIGHT: Turn the left adjusting bolt ¼ turn counterclockwise, or the right adjusting bolt ¼ turn clockwise. This moves the running belt to the left.
(Refer to the belt adjustment diagrams on page 9 of the PDF manual for visual guidance.)
Important:
- Do not turn the adjusting bolt more than ¼ turn at a time. Overtightening can damage the treadmill.
- Recheck the belt alignment by repeating the steps.
Note: Running belt deviation is not covered by warranty. It is the user's responsibility to maintain the belt according to these instructions. Deviation can seriously damage the running belt and affect its service life, so adjust it promptly if it occurs.
7. Troubleshooting
This section provides solutions for common error codes and issues you might encounter.
| Serial No. | Error | Instructions | Overhaul |
|---|---|---|---|
| 1 | E02 | Hall detection error reported. |
|
| 2 | E03 | Overcurrent error reported. |
|
| 3 | E04 | Overvoltage error reported. |
|
| 4 | E05 | Undervoltage error reported. |
|
| 5 | E06 | Overload error reported. |
|
| 6 | E08 | Downcontrol overheat error. |
|
| 7 | E09 | Lift motor detection error reported. |
|
| 8 | E11 | UVW three wire simultaneously open circuit error. |
|
| 9 | E12 | The lower control cannot receive the relay signal error. |
|
| 10 | E13 | Relay cannot receive digital watch signal error. |
|
| 11 | E07 | Error reported when safety lock comes off. |
|
8. Specifications
Major Parameters
| No. | Parameter | Specification |
|---|---|---|
| 1 | Rated voltage | 220V-240V |
| 2 | Rated frequency | 50Hz |
| 3 | Rated peak value | 3.0HP |
| 4 | Speed | 1-12 KM/H |
| 5 | Running belt area | 970*400 mm (97 x 40 cm) |
| 6 | Max capacity | 136 KG (350 LB) |
| 7 | Expanded measurement | 1144*584*990 mm |
| 8 | Adjustable slope | Yes (15% Incline) |
| 9 | Foldable | Yes |
| 10 | With Speakers | No |
| 11 | Bluetooth connection available | No |
| 12 | Screen | No (Features a tablet holder for personal devices) |
| 13 | Power Supply Compliance | 50Vac or 75Vdc or Higher Power Supply |
| 14 | Training Site | Legs, Muscle Relex Apparatus, Foot |
| 15 | Type of sports | Cardio Training |
Packing List
| No. | Description | Qty |
|---|---|---|
| 1 | Treadmill machine | 1 |
| 2 | Allen wrench 5mm | 1 |
| 3 | Safety lock | 1 |
| 4 | User manual | 1 |
| 5 | Knob M8*50 | 2 |
| 6 | Knob M8*37 | 2 |
Package Dimensions & Weight
- Length: 113 cm
- Width: 55 cm
- Height: 10 cm
- Weight: 21.3 kg
9. User Tips
- The ROBORE SF20 treadmill operates quietly, making it suitable for use in home and office environments without causing disturbance.
- This is an electric treadmill, designed for powered operation. Ensure it is connected to a suitable power source as per specifications.
10. Warranty and Support
For detailed warranty information, technical support, or service inquiries, please refer to the official product documentation or contact customer service through your point of purchase.
A comprehensive user manual in PDF format is available for download: ROBORE SF20 User Manual (PDF)