1. Introduction
Thank you for choosing the Ziqqucu SFT-RD96 Dual-Channel FM Radio Electronic DIY Kit. This kit provides an engaging soldering project for enthusiasts to build a functional FM radio with a digital display and Type-C power interface. This manual will guide you through the assembly, operation, and maintenance of your new radio.
2. Safety Information
- Soldering Safety: Always use appropriate personal protective equipment (PPE) such as safety glasses. Work in a well-ventilated area to avoid inhaling solder fumes. Ensure your soldering iron is on a heat-resistant stand when not in use.
- Electrical Safety: Be cautious when handling electronic components. Ensure power is disconnected before making any adjustments or repairs.
- Component Handling: Some components are sensitive to static electricity. Handle them by their edges or leads, and consider using anti-static precautions.
- Battery Safety: If using a lithium battery, ensure it is inserted with correct polarity. Do not short-circuit the battery. Use only recommended battery types (18650 flat-top).
- Adult Supervision: This kit contains small parts and requires soldering. Adult supervision is recommended for younger builders.
3. Package Contents
Please check your kit against the following list. Components may vary slightly based on whether you ordered the kit with or without the acrylic casing.
Common Components:
- Main PCB (Printed Circuit Board)
- STC15W408AS Microcontroller
- RDA5807M FM Receiver Module
- AXS2031 Digital Amplifier Chip
- 3.3V Buck-Boost Module
- Digital Display (LED Segment Display)
- 2 x 4 Ohm 3W Speakers
- Universal Rod Antenna (adjustable)
- Type-C Charging Protection Board
- Resistors, Capacitors, Transistors, Diodes
- Push Buttons (for volume/frequency control)
- 3.5mm Audio Jack
- Battery Holder (for 18650 battery - battery not included)
- Connecting Wires
- USB Type-A to Type-C Cable
Additional Components (if 'With Case' option selected):
- Acrylic Casing Panels
- Hexagonal Copper Pillars and Screws for Casing Assembly

Figure 3.1: Kit components (without casing)

Figure 3.2: Kit components (with acrylic casing)
4. Setup and Assembly
This section provides detailed instructions for assembling your FM radio kit. A good quality soldering station and magnification glasses are highly recommended for precision work.
4.1. Pre-Assembly Checks
- Verify all components are present as per the package contents list.
- Use a multimeter to test components like transistors, capacitors, and resistors for functionality before soldering.
4.2. Soldering Instructions
- Surface Mount Components: Begin by soldering thinner surface mount components and modules (e.g., RDA5807M, AXS2031, 3.3V buck-boost module). You can apply solder paste and use a hot air gun, or carefully use a fine-tip soldering iron.
- Through-Hole Components: Use a bracket to elevate the PCB. Insert through-hole components (resistors, capacitors, IC sockets, buttons) according to their part numbers and height.
- Securing Components: To prevent components from falling out during soldering, use adhesive tape to temporarily secure them to the edges of the PCB.
- Trimming Leads: Flip the PCB over. Trim component leads to approximately 1mm in length before soldering.
- Soldering Order: Follow the principle of soldering from the lowest height components to the tallest.
4.3. Final Assembly Steps
- Antenna Installation: Secure the flat feet of the universal antenna to the back of the PCB using solder. Fix it with M3 screws, adjust for verticality, and reinforce with additional solder.
- Battery Holder and Wiring: Solder the battery holder wires to the designated pads on the PCB (usually marked BATT+ and BATT-). Secure the battery holder to the PCB with screws.
- Speaker Connection: Connect the speaker wires to the SPK1 and SPK2 output pads on the PCB.
- Casing Assembly (if applicable):
- After PCB soldering is complete, screw the hexagonal copper pillars into the PCB.
- Install the front acrylic panel and tighten its screws.
- Assemble the side panels.
- Finally, attach the back acrylic panel and tighten its screws.

Figure 4.1: Antenna installation and reinforcement

Figure 4.2: PCB with battery holder and speakers installed

Figure 4.3: Final casing assembly
4.4. Power Supply
Your radio supports two power supply methods, which can be used simultaneously:
- Type-C 5V Power: Connect a standard USB Type-C cable to the Type-C port on the radio. This will power the radio and simultaneously charge an installed 18650 lithium battery. Charging automatically stops when the battery is full.
- 3.7V Lithium Battery: Insert a fully charged 18650 flat-top lithium battery into the battery holder, ensuring correct polarity.

Figure 4.4: Internal view showing battery and Type-C charging board

Figure 4.5: Radio connected via Type-C for power and charging
5. Operating Instructions
5.1. Basic Operation
- Power On/Off: Locate the power switch on the radio and slide it to the 'ON' position to power on. Slide to 'OFF' to power off.
- Digital Display: The blue LED display shows the current volume level or the received frequency in real-time.
5.2. Controls

Figure 5.1: Functional schematic diagram of controls
- Volume Up/Down: Short press the respective buttons once to increase or decrease the volume by one level.
- Frequency Adjustment:
- Auto-Scan: Long press the frequency addition or reduction button to automatically scan for available channels.
- Manual Adjustment: Short press the frequency addition or reduction button to adjust the frequency by 0.1MHz increments.
5.3. Antenna Adjustment
The universal rod antenna can be rotated and adjusted in any direction. Extend and adjust the angle of the antenna for optimal reception effect, especially in areas with weak signals.

Figure 5.2: Universal antenna for improved reception
5.4. Audio Output
The radio features a 3.5mm audio output jack. You can connect headphones directly to this port for private listening, or connect it to an external amplifier using a 3.5mm audio cable to drive larger speakers.

Figure 5.3: Power switch and 3.5mm audio output interface
6. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the radio. Do not use abrasive cleaners or solvents.
- Storage: Store the radio in a cool, dry place away from direct sunlight and extreme temperatures.
- Battery Care: If not using the radio for an extended period, it is advisable to remove the 18650 lithium battery.
- Avoid Drops: Protect the radio from physical shocks and drops, especially if it has an acrylic casing, which can crack.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Radio does not power on | No power source; Battery drained; Incorrect battery polarity; Loose power connection; Power switch fault. | Ensure Type-C power is connected or battery is charged and correctly inserted. Check all power connections and switch. |
| No sound from speakers | Volume too low; Speaker wires loose/disconnected; Faulty speaker; Amplifier chip issue. | Increase volume. Check speaker connections. Test speakers if possible. Verify amplifier chip soldering. |
| Poor FM reception | Antenna not extended/adjusted; Weak signal area; Interference; RDA5807M module issue. | Fully extend and adjust antenna. Try moving to a different location. Check RDA5807M module connections. |
| Digital display not working or showing errors | Low power supply voltage (below 3V); Loose display connection; Faulty display. | Ensure power supply is stable (2.5-5.5V). Check display connections. |
| Distorted sound | Low power supply voltage; Overdriven volume; Faulty amplifier. | Check power supply. Reduce volume. Verify amplifier chip soldering. |
8. Specifications
| Feature | Specification |
|---|---|
| Main Control Chip | STC15W408AS Microcontroller |
| FM Receiver Module | RDA5807M |
| Amplifier Chip | AXS2031 Digital Amplifier |
| Power Supply Voltage | 2.5V - 5.5V |
| Power Sources | Type-C 5V, 3.7V Lithium Battery (18650 Flat-Top) |
| Receiving Band | FM Band |
| Frequency Range | 87.5MHz - 108MHz |
| Output Power | 5W + 5W Dual Channel |
| Antenna | Omnidirectional, Adjustable |
| Audio Output | 3.5mm Jack (Headphones/Amplifier) |
| Display | Blue LED Digital Display |
9. User Tips
- Soldering Tools: For the best assembly experience, invest in a good quality soldering station with temperature control and consider using magnification glasses for precise work.
- Battery Not Included: Please note that the 18650 lithium battery required for portable operation is not included in the kit and must be purchased separately.
- Casing Option: This kit is available with or without an acrylic casing. Please verify your order to confirm which version you purchased. If you ordered the 'without case' option, the acrylic shell components will not be included.
- Component Orientation: Pay close attention to the orientation of integrated circuits (ICs) and polarized components (like electrolytic capacitors and diodes) during soldering to avoid damage.
- Testing: It's good practice to test components before soldering, especially if you are new to electronics DIY.
10. Warranty and Support
For any issues, missing parts, or technical support not covered in this manual, please contact the seller directly through your purchase platform. Please provide your order details and a clear description of the problem for efficient assistance.
Product Overview Video
Video 1: A visual demonstration of the assembled Ziqqucu SFT-RD96 FM Radio Kit, showcasing its design and features from various angles.
Additional Resources
A PDF user manual is also available for this product. Please refer to the product page or contact the seller for access to the PDF document.