UXCELL LED Indicator Light

Contents

Uxcell LED Signal Indicator Lights

Model: LED Indicator Light | Brand: UXCELL

1. Introduction

This manual provides essential information for the safe and effective use of your Uxcell LED Signal Indicator Lights. These panel mount indicator lights are designed for various applications, including signal indication and status display in household appliances, switch valves, and industrial equipment. Please read all instructions carefully before installation and operation.

2. Safety & Warnings

To ensure safety and prevent damage, please observe the following warnings:

  • Read all instructions before use to ensure safety and prevent damage.
  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Do not use over voltage.
  • Do not disassemble the product.
  • Do not expose the product to water.
  • Confirm positive and negative polarity before wiring to prevent damage to the LED.
  • For indication use only.

3. Package Contents

Your package should contain the following items:

  • 5 or 10 pieces of LED Indicator Lights (depending on the purchased set)
A set of five LED signal indicator lights in various colors with pre-wired leads.
Figure 1: Example of LED Indicator Light Set (colors may vary)

4. Specifications

Feature Specification
Product Name LED Indicator Light
Brand UXCELL
Material Zinc Alloy, Plastic
Light Color Options Red, Yellow, Blue, Green, White
Rated Voltage AC/DC 12V, AC/DC 24V, AC/DC 110V (depending on model)
Is Bulbs Included Yes
Luminous Flux <60
Power Source AC
Mounting Hole Diameter 8mm / 0.31 inch
Thread Diameter 7.6mm / 0.3 inch
Thread Length 8mm / 0.31 inch
Cable Length 200mm / 7.9 inch
Certification NONE
Origin Mainland China
A diagram illustrating the mounting dimensions of the LED indicator light, showing an 8mm (0.31 inch) mounting hole diameter and a 7.6mm (0.3 inch) thread diameter with an 8mm (0.31 inch) thread length.
Figure 2: Mounting Dimensions

5. Setup

These LED indicator lights are designed for easy panel mounting and connection.

5.1 Installation Steps

  1. Prepare Mounting Hole: Drill a hole with a diameter of 8mm (0.31 inch) in your panel. Refer to Figure 2 for precise dimensions.
  2. Insert Indicator Light: Insert the threaded portion of the LED indicator light into the prepared hole.
  3. Secure with Nut and Washer: Secure the indicator light in place using the provided nut and washer. Ensure it is tightened firmly for a stable connection.
  4. Wiring: The indicator light comes with pre-wired leads. The red wire is positive (+), and the black wire is negative (-). Confirm the positive and negative polarity of your power source before connecting.
  5. Connect to Power Source: Connect the red wire to the positive terminal and the black wire to the negative terminal of your AC/DC 12V, 24V, or 110V power source, depending on the specific model of your indicator light.
A single red LED signal indicator light with a 200mm (7.9 inch) cable, specified for AC/DC 12V operation.
Figure 3: 12V LED Indicator Light with 200mm Cable
A single red LED signal indicator light with a 200mm (7.9 inch) cable, specified for AC/DC 110V operation.
Figure 4: 110V LED Indicator Light with 200mm Cable

6. Operating Instructions

Once properly installed and wired, the LED indicator light will illuminate when power is supplied to its terminals, providing a visual signal or status indication. The light will turn off when power is removed.

A collage showing close-up views of the LED indicator lights illuminated in different colors: blue, white, green, red, and yellow.
Figure 5: Various Illuminated LED Indicator Lights

7. Maintenance

These LED indicator lights are designed for low maintenance. Follow these guidelines for optimal performance:

  • Cleaning: Use a soft, dry cloth to clean the surface of the indicator light. Avoid abrasive cleaners or solvents that could damage the material.
  • Inspection: Periodically check the wiring connections to ensure they remain secure and free from corrosion.
  • Environmental Conditions: Ensure the operating environment is free from excessive moisture or extreme temperatures, as these can affect the lifespan and performance of the LED.

8. Troubleshooting

If your LED indicator light is not functioning as expected, consider the following:

  • Light Not Illuminating:
    • Check the power supply to ensure it is active and providing the correct voltage (12V, 24V, or 110V, matching your specific indicator light model).
    • Verify that the wiring connections are correct and secure. Ensure the red wire is connected to positive (+) and the black wire to negative (-).
    • Inspect the LED for any visible damage.
  • Intermittent Lighting:
    • Check for loose wiring connections at both the indicator light and the power source.
    • Ensure there are no shorts in the wiring.

9. User Tips

  • Color Coding: Utilize different colored indicator lights (Red, Yellow, Blue, Green, White) to represent different statuses or conditions in your application for quick visual identification.
  • Secure Mounting: Always ensure the indicator light is securely fastened with its nut and washer to prevent loosening due to vibration, especially in industrial settings.
  • Voltage Matching: Double-check that the voltage rating of the indicator light (12V, 24V, or 110V) precisely matches your power supply to avoid damage and ensure proper operation.

10. Manufacturer Information

Manufacturer

Guangzhou Dajiali Network Technology Co., Ltd.
B395, Room 106, Rulin Street, Tianhe, Guangzhou, China
Email: udb7910@126.com

EU Authorized Representative

Apex CE Specialists GmbH
Room 1411, Lankun Building, No. 213 Minkang Road, Longhua District, Shenzhen, Guangdong
Email: Info@apex-ce.com

© 2024 Uxcell. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.