HYUNDAI GENESIS BH

Contents

Hyundai Genesis Rear View Camera User Manual

Model Compatibility: HYUNDAI GENESIS (BH) 3.8 V6 (2008-2014 G6DA), GENESIS (BH) 4.6 (2008-2010 G8BA)

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your new rear view camera for Hyundai Genesis vehicles. This camera is designed to assist drivers with parking and reversing maneuvers by providing a clear view of the area behind the vehicle.

Hyundai Genesis Rear View Camera

Figure 1: Rear View Camera Unit

2. Safety Information

  • Always disconnect the vehicle's power supply by removing the negative terminal of the battery before beginning any electrical work to prevent short circuits and electrical shock.
  • Ensure the vehicle is turned off and the handbrake is engaged during installation.
  • If you are unsure about any step, consult a professional automotive technician.
  • Use appropriate personal protective equipment (PPE) such as safety glasses and gloves.
  • Ensure all wiring is properly insulated and secured to prevent damage from vibration or moving parts.

3. Package Contents

Your rear view camera kit should include the following items:

  • Rear View Camera Unit
  • Connection Cable (Video Signal Cable)
  • Power Cable (for camera)
Camera Wiring Connector

Figure 2: Camera Wiring Connector

4. Setup and Installation

4.1. Preparation Before Installation

Tools and Materials Required:

  • Reverse camera kit (including camera, connection cable, power cable, etc.)
  • Screwdriver set
  • Wire stripper
  • Electrical tape
  • Electric drill (if needed for drilling and fixing)
  • Multimeter (optional, for circuit testing)

Safety Check:

  • Before installation, disconnect the vehicle's power supply (remove the negative terminal of the battery to prevent short circuits).
  • Make sure the vehicle is turned off and the handbrake is engaged.

4.2. Installation Steps

Determine the Position of the Camera:

  • Common locations: above the license plate, on the trunk handle, or on the rear bumper (drilling may be required depending on the chosen spot).
  • Choose a position with an unobstructed view and ensure the camera is tilted downward at approximately 15° (this angle typically covers the license plate and the ground directly behind the vehicle).

Wiring Operation:

  1. Rear Trunk Wiring: Remove the rear trunk interior panel. Route the camera wiring harness along the original vehicle's wiring path, taking care to avoid interference with any moving parts (e.g., trunk hinges, latches).
  2. Pass the wiring harness through existing rubber sleeves (such as those at the rear trunk hinge) to enter the vehicle's interior cabin.
  3. Connect to the Reverse Light Power Supply:
    • Locate the vehicle's reverse light wire. This wire is usually green or yellow. You can use a multimeter to detect voltage on this wire when the reverse gear is engaged to confirm it is the correct power source.
    • Connect the red power wire of the camera to the positive terminal of the reverse light wire.
    • Connect the black wire of the camera to a suitable ground point on the vehicle chassis.

Fix the Camera:

  • Fix the camera base securely with screws or 3M adhesive to ensure it is stable and does not shake during vehicle operation.
  • If drilling holes is necessary, first measure the required hole diameter. Operate carefully with a hand drill to avoid damaging the car paint.

Connect the Display:

  • If using an independent monitor: Connect the video cable from the camera to the monitor's video input. Power the monitor via the cigarette lighter or an ACC (Accessory) power source.
  • If connecting to the original car's central control screen: The camera needs to be connected through the AV input interface or a dedicated adapter, if available. For some vehicle models, the reversing camera function may need to be activated in the vehicle's settings or by a dealership.

5. Operating Instructions

Once properly installed, the rear view camera will automatically activate when the vehicle's transmission is shifted into reverse gear. The image from the camera will be displayed on your connected monitor or the vehicle's central screen, providing a clear view of the area behind your vehicle.

  • Always check your surroundings visually in addition to using the camera display. The camera is an aid and does not replace safe driving practices.
  • Be aware of the camera's field of view; objects outside this view may not be visible.

6. Maintenance

  • Cleaning the Lens: Periodically clean the camera lens with a soft, damp cloth to remove dirt, dust, or water spots that may obstruct the view. Do not use abrasive cleaners.
  • Checking Connections: Occasionally inspect the wiring connections to ensure they are secure and free from corrosion or damage.
  • Environmental Factors: In harsh weather conditions (heavy rain, snow, extreme temperatures), the camera's performance may be temporarily affected.

7. Troubleshooting

ProblemPossible CauseSolution
No image on displayLoose power or video connection; Camera not receiving power; Display input not selected.Check all cable connections; Verify camera is receiving power when in reverse; Ensure display is set to correct input.
Distorted or flickering imagePoor video connection; Electrical interference; Damaged cable.Secure video cable connections; Check for nearby electrical interference; Inspect cable for damage.
Image is dark or unclearDirty camera lens; Low light conditions; Camera angle incorrect.Clean camera lens; Adjust camera angle for better view.
Camera does not activateNo power from reverse light; Faulty reverse light switch.Verify power to camera when in reverse using a multimeter; Check vehicle's reverse light circuit.

8. Specifications

  • OEM Part Numbers: 957603M060, 957603M000
  • Compatible Models: HYUNDAI GENESIS (BH) 3.8 V6 (2008-2014 G6DA), HYUNDAI GENESIS (BH) 4.6 (2008-2010 G8BA)
  • Origin: Mainland China
  • Package Dimensions (Approx.): 20 cm (Length) x 10 cm (Width) x 10 cm (Height)
  • Package Weight (Approx.): 0.068 kg

9. User Tips

No specific user tips are available at this time. Always ensure the camera lens is clean for optimal visibility.

10. Warranty and Support

For any warranty claims, technical support, or further assistance, please contact your original seller or retailer. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.