XTOOL KC501

Contents

XTOOL KC501 Key & Chip Programmer User Manual

Model: KC501 | Brand: XTOOL

XTOOL D7S Automotive Scanner with KC501 Key & Chip Programmer

The XTOOL D7S Automotive Scanner, compatible with the KC501 Key & Chip Programmer.

Product Overview Video

Official product video showcasing the capabilities of the XTOOL D7S Automotive Diagnostic Scanner, which the KC501 accessory enhances.

1. General Introduction

The XTOOL KC501 is a versatile key and chip programmer designed to work with advanced XTOOL diagnosis/key programming tablets (excluding P700 series due to port incompatibility) or PC/laptops with KC501 Studio installed. It supports a wide range of functions essential for automotive key and immobilizer services.

Key Functions:

  • Read & write car keys & key chips
  • Generate dealer keys
  • Write data to key emulators
  • Read remote frequency, chip type & chip ID
  • Read & write Mercedes-Benz infrared keys
  • Read & write MCU/EEPROM chips

Note: Some XTOOL tablets, such as the P700 series, do not feature USB-C or USB-A ports and are therefore not compatible with the KC501.

For a complete and detailed user manual in PDF format, please refer to the official document: KC501 User Manual (PDF).

2. Product Overview: KC501 Exposed View

The KC501 Key & Chip Programmer features several ports and slots for various operations. Understanding each component is crucial for proper use.

Component Descriptions:

  1. DC Port: Provides 12V DC power supply. Essential for MCU/ECU reading & writing processes.
  2. USB-B Port: Facilitates data transmission between KC501 and XTOOL devices or PC. Also supplies 5V power.
  3. DB 26-Pin Port: Connects to Mercedes-Benz infrared cable, ECU cable, MCU cable, and MC9S12 cable.
  4. Cross Signal Pins: Holds MCU board, MCU spare cable, or DIY signal interface for reading/writing MCU and ECU chips.
  5. Locker: Secures the EEPROM component transponder slot.
  6. EEPROM Component Transponder Slot: Accommodates EEPROM plug-in transponders or EEPROM sockets for reading/writing EEPROM chips. Pin 1 is located at the right-bottom corner.
  7. Status LED: Indicates the current operating status of the device.
  8. IC Card Induction Area: Used for reading and writing IC card data.
  9. Display Screen: Shows remote frequency or transponder ID.
  10. Remote Frequency Button: Press to display remote frequency on the screen.
  11. Transponder ID Button: Press to display transponder type and ID on the screen.
  12. Transponder Slot: Holds transponders for reading or writing data.
  13. Vehicle Key Slot: Used to hold vehicle keys for reading or writing data.
  14. Remote Control Transponder Induction Area: Used to read and write remote control transponder data.
  15. Mercedes Infrared Key Slot: Used to read or write Mercedes vehicle key data.

3. Technical Specifications

ItemDescription
Display0.96-inch 128x64 Monochrome OLED screen
Input Voltage5V (USB-B) / 12V (DC)
Working Temperature-10°C to 50°C (14°F to 122°F)
Storage Temperature-20°C to 60°C (-4°F to 140°F)
Related Humidity< 90%
PortsDC charging port, USB-B port, DB26 port
Relative Humidity10% ~ 90%
Size176 x 85 x 32 mm

4. Accessories

The KC501 Key & Chip Programmer comes with several accessories to facilitate various key and chip programming tasks.

  • FQFP Boards: Used for welding microcontrollers to make jump wires easier. Includes 5 different boards for microcontrollers with 64/80/112/144/176 pins. Ensure correct orientation (white dot indicates pin 1).
  • EEPROM PCBA: For reading and writing EEPROM chips on a bench.
  • EEPROM Chip Test Stand: Holds EEPROM chips for bench reading and writing.
  • IC Clip Cable: Allows reading and writing EEPROM chips without desoldering them from the module.
  • Color Cable: Connects to the 26-pin connector for jumping wires to read/write data on modules.
  • DuPont Cable: Individual cables for multi-purpose use, such as jumpers or reading data.
  • Mercedes IR Key Emulator: Used to read and collect EIS/EZS data during Mercedes-Benz key programming.
  • XTA Cables: Wiring harnesses for ECU reading and writing. Connects the DB26 socket to the KC501 and jump wires to modules.
  • USB3.0 to USB-B Cable: Connects KC501 to XTOOL tablets or PC/laptops for data transfer and power supply.
  • USB3.0 to USB-C Adapter: Enables KC501 use with devices featuring USB-C ports.
  • Power Adapter (DC12V/AC100~240V): Provides 12V DC power supply for operations requiring external power, such as module programming.

5. How to Use

5.1 Program Keys & Emulators

The KC501 is required for specific key programming processes on XTOOL devices. When needed, your XTOOL device will prompt you to connect the KC501. Use the USB3.0 to USB-B cable to connect it to your XTOOL tablet or PC. The key programming software will guide you through the subsequent steps.

Note: For first-time use with a tablet, you will be prompted to bind the device. To use it with another tablet, contact XTOOL aftersales services with a PC or laptop.

5.2 Read Remote Frequency

To determine the frequency of a remote key:

  1. Connect KC501 to a power supply.
  2. Insert the key into the slot with the remote signal-radiation side facing down.
  3. Press the "FR" button on the KC501.
  4. Press any button on the remote key.
  5. The frequency will be displayed on the screen (e.g., 433.61MHZ).

5.3 Read Transponder ID & Chip Type

To read the transponder ID and chip type of a key:

  1. Connect KC501 to a power supply.
  2. Insert the key into the slot.
  3. Press the "TR" button on the KC501.
  4. The transponder ID and chip type will be displayed on the screen (e.g., KEY: 4A, ID: XXXXXXXX).

5.4 EEPROM Reading & Writing

EEPROM chips can be installed in multiple ways, each requiring specific accessories.

5.4.1 Installing EEPROM Chip Directly

  1. Switch the locker up to unlock the slot.
  2. Place the EEPROM chip into the slot, ensuring pin 1 (usually marked) is in the right-bottom corner.
  3. Switch the locker down to secure the chip.

Note: This method is only for large-sized EEPROM chips. Ensure the chip is firmly held.

5.4.2 Installing EEPROM Chip via EEPROM PCBA

  1. Weld or install the EEPROM chip onto the PCBA.
  2. Turn the PCBA so the side with characters faces the front (characters will appear upside down).
  3. Install the PCBA onto the KC501's cross-signal pins.

Note: Before welding, ensure correct orientation; a groove or dot indicates pin 1 on the PCBA.

5.4.3 Installing EEPROM Chip via IC Test Stand

  1. Orient the IC test stand so its internal pins are on the right side, with the right-bottom corner indicating pin 1.
  2. Press the locker on the stand and insert the EEPROM chip, aligning pin 1.
  3. Switch the KC501's locker up to unlock the slot.
  4. Insert the IC test stand into the KC501 slot, aligning pin 1 of the stand with the slot.
  5. Switch the KC501's locker down to secure the stand.

Note: This method is for small-sized EEPROM chips. Ensure the chip and stand are firmly held.

5.4.4 Installing EEPROM Chip via IC Clip Cable

  1. Switch the KC501's locker up to unlock the slot.
  2. Insert the pin-side of the clip cable into the slot, ensuring the red-marked wire (pin 1) faces the bottom of the KC501.
  3. Switch the KC501's locker down to secure the cable.
  4. Clip the IC clip onto the corresponding EEPROM chip firmly.

Note: This method is for small-sized EEPROM chips and does not require desoldering.

5.5 Read & Write EEPROM on Tablets

After installing the EEPROM chip and connecting the KC501 to your XTOOL tablet:

  1. Navigate to "Special Function" > "EEPROM Adapter".
  2. Select "Read/Write EEPROM" and then "KC501".
  3. Choose the EEPROM brand, model, and scale from the menus.
  4. Click "Read data". The KC501 will read the data.
  5. After reading, you can edit the EEPROM file name and save it as a BIN file.
  6. To write data, select "Write data", choose the file, and confirm.

Note: Refer to the Support List for compatible EEPROM chips. You can also use the "Operation document" for pin 1 recognition.

5.6 Read & Write ECU/BCM Data

To read and write ECU/BCM data using KC501 and XTOOL tablets:

  1. Connect KC501 to the tablet.
  2. Go to "EEPROM Adapter" > "Read/Write ECU data".
  3. Select the desired ECU/BCM.
  4. Open the "Operation document" to view wiring diagrams.
  5. Use the XTA wiring harness or DuPont cable to connect the ECU/BCM to the KC501.
  6. Click "Read data" to read the data from the module.
  7. After reading, you can edit the file name and save it as a BIN file.
  8. To write data, click "Write data", select the file, and confirm.

Note: Refer to the Support List for compatible ECU/BCM modules. A 12V DC power supply is recommended for these operations.

5.7 Functions on PC/Laptop (KC501 Studio)

Before using KC501 with a PC or laptop, ensure "KC501 Studio" is installed. Download it from the XTOOL official website (Support > Download Center > Upgrade tool > KC501). KC501 Studio is compatible with Windows 7 and later. It is recommended to disable anti-virus software during installation.

5.8 Read & Write EEPROM With PC/Laptop

Using KC501 Studio on your PC:

  1. Select the correct EEPROM brand, model, and scale, or open an existing BIN file.
  2. Click "Read" to read data. The results will be displayed, allowing direct editing or saving as a BIN file.
  3. To write data, click "Write", select the file, and confirm.

5.9 Read & Write Transponder Chip With PC/Laptop

This function supports ID46/48 keys. To perform this operation:

  1. Insert the key or transponder chip into the KC501 slot.
  2. Connect KC501 to your PC/laptop.
  3. In KC501 Studio, click the "Key" menu on the left.
  4. Select the key type you are reading.
  5. Click "Read" for each column to display data. You can edit the results and click "Write" to save changes.

6. Support List

The KC501 Key & Chip Programmer supports a wide range of vehicles and chip types. This list is updated regularly; please refer to the XTOOL official website for the latest information.

6.1 Key Programming Support List (Partial)

ManufacturerModelsYear/IMMO TypeUsageSide Notes
ALLALL3.5th Gen. IMMOGenerate TP21/TP22/TP23/TP24 specialized 48 chips
BMWALLEWS2/EWS3/EWS4(44 Chip)Generate key/Read&write D-FLASHOnly EWS4 supports read EEPROM
ALLCAS1/CAS2/CAS3(46 Chip)Generate pre-processed key
ALLCAS4(49 Chip)Generate key/Read&write D-FLASH
ALLFEM/BDCRead&write EEPROM data
A6/Q74th Gen. IMMO (8E Chip) 2005-2012Generate dealer key / Read&write D-FLASH (In AKL situations)
PASSAT/CC4th Gen. IMMO (48/46 Chip)Generate dealer key / Read EEPROM dataSmart key--46 Chip, Semi-smart key--48 Chip
Mercedes-BenzALLFBS3 IMMO (Infrared key)Generate Infrared Key
EIZ-W211 (ST12)MC9S12DT128

Note: This is a partial list. For a complete and up-to-date list, please refer to the XTOOL official website or KC501 Studio software.

6.2 EEPROM Support List (Partial)

ManufacturerEEPROM Chip Type
I2C24C01
24C02
24C04
24C08
24C16
24C32
AtmelAT24C01
AT24C02
AT24C04
AT24C08
AT24C16
AT25010(8)

Note: This is a partial list. For a complete and up-to-date list, please refer to the XTOOL official website or KC501 Studio software.

6.3 ECU Support List (Partial)

ManufacturerModelsMCU Type
BMWEWS2
EWS3
EWS4MC9S12DJ64
CAS2-2K79XMC9S12DG256
CAS3-0L15Y
CAS3-0M23SMC9S12XDP512
PorscheBCM-2M25JMC9S12XET512
BCM-1L15YMC9S12XEP100

Note: This is a partial list. For a complete and up-to-date list, please refer to the XTOOL official website or KC501 Studio software.

7. Troubleshooting

Q1: The lights on the device glow dimly.

A1: Check the following:

  • Ensure you are using original USB cables from KC501.
  • Connect the KC501 with a 12V power supply and check the status of the lights.
  • Inspect the USB socket conditions on both the tablet/PC and KC501 for damage.

Q2: KC501 connects to PC/laptop but gets no response.

A2: First, ensure "KC501 Studio" is installed on your PC. Then check the following:

  • Check the lights on KC501. If they are not glowing or glowing dimly, refer to Q1.
  • Open Device Manager on your PC and verify if KC501 is listed under USB ports.
  • If the device is not loaded properly, close KC501 Studio, disconnect KC501, navigate to the KC501 Studio installation directory (e.g., C:\Program Files (x86)\Xtooltech\KC501Studio), open the "drivers" folder, and manually select the appropriate driver for your PC settings.

Note: Disable anti-virus software before installing drivers and set the driver as trusted if prompted.

Q3: KC501 shows "not connected" when connected to a tablet.

A3: Check the following:

  • Check USB cables (refer to A1 for details).
  • Go to "EEPROM Adapter" > "Read KC501 firmware" and send screenshots of the results to XTOOL aftersales services.
  • If still not connected, check the USB socket conditions on both devices.
  • Alternatively, try installing KC501 Studio on a PC first to see if KC501 is recognized.

Q4: KC501 shows "The device bounded by (other S/N)" during programming.

A4: This indicates the KC501 has been used on another device. Connect it to a PC and contact XTOOL aftersales services for assistance.

Q5: "Hardware not supported" error on supported XTOOL tablets.

A5: Ensure you have downloaded "IMMOBILIZER-KC501LIB" in the updates for your tablet.

8. User Tips

  • Always keep your KC501 Studio software and tablet applications updated to ensure compatibility and access to the latest features and vehicle support.
  • When performing sensitive operations like ECU coding or EEPROM writing, ensure a stable power supply to avoid interruptions that could damage modules.
  • Double-check all wiring connections before initiating any diagnostic or programming procedure to prevent incorrect data transfer or damage.

9. Warranty & Support

The XTOOL KC501 Key & Chip Programmer comes with a 2-year warranty and 3 years of free updates, ensuring reliable and trustworthy performance.

Aftersales Services:

Company Information:

  • Company Address: 17&18/F, Building A2, Creativity City, Liuxian Avenue, Nanshan District, Shenzhen, China
  • Factory Address: 2/F, Building 12, Tangtou Third Industrial Zone, Shiyan Street, Baoan District, Shenzhen, China
  • Fax: 0755-83461644

XTOOL reserves the right for the final interpretation of this manual content.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.