1. Product Overview
The Mitutoyo Digital Caliper, specifically the 500-196-30 series, is an advanced universal measuring tool designed for high precision. It utilizes a non-contact capacitive grating displacement measurement system and features a clear digital LCD display for intuitive readings. This caliper offers high measurement efficiency and ease of use, making it suitable for various applications requiring accurate dimensional measurements.

The series includes models with different measurement ranges, such as 0-150mm (0-6"), 0-200mm (0-8"), and 0-300mm (0-12"), all maintaining high accuracy and repeatability. The caliper is powered by a single 1.5V silver oxide battery, providing approximately 12 months of continuous operation.
2. Specifications
| Feature | Specification |
|---|---|
| Brand Name | Mitutoyo |
| Model Number Series | 500-(196/197/193)-30 |
| Origin | Mainland China |
| Display Type | Digital |
| Accuracy | 0.01mm (0.0005") |
| Measurement Range | 0-150mm (0-6"), 0-200mm (0-8"), 0-300mm (0-12") |
| Reading Value | 0.01mm (0.0005") |
| Indication Error | 0.03mm (0.001") |
| Measurement Repeatability | 0.01mm (0.0005") |
| Maximum Measuring Speed | 1m/s |
| Operating Temperature | 0~40℃ |
| Storage/Transport Temperature | -20~70℃ |
| Humidity Effect | Relative humidity ≤ 80% unaffected |
| Power Supply | 1x 1.5V Silver Oxide Battery |
| Battery Life | Approx. 12 months continuous use |
| DIY Supplies Category | Plumbing |
| High-concerned chemical | None |
3. Components and Controls
Familiarize yourself with the parts of your digital caliper:

- Inner Jaws (Knige mouth inside measurement claw): Used for internal dimension measurements.
- Outer Jaws (Outside measurement claw): Used for external dimension measurements.
- Tightening Screw: Locks the slider in position to hold a measurement.
- mm/in Button: Toggles between millimeter and inch measurement units.
- ORIGIN Button: Sets the absolute origin point for measurement.
- ON/OFF Button: Powers the unit on or off.
- ZERO Button: Sets the display to zero at any slider position for incremental measurements.
- Ruler Body: The main scale of the caliper.
- Battery Compartment/Data Output Port: Area for battery replacement and RS-232 data output connection.
- Thumb Roller (Measurement fine adjustment): Allows for fine adjustment of the slider position.
- Depth Rod (Measurement depth): Used for measuring depths of holes or steps.
- Step Measuring Face (Step measurement surface): Used for measuring step dimensions.

4. Setup
4.1 Initial Inspection
Upon receiving your Mitutoyo Digital Caliper, inspect it for any signs of damage. Ensure all components are present and the display is clear.
4.2 Battery Installation
The caliper is powered by one 1.5V silver oxide battery. If the display is dim or not showing, the battery may need to be installed or replaced.
- Locate the battery compartment cover (part of item 9 in Figure 2).
- Gently slide the cover in the direction indicated by the arrow to open it.
- Insert a new 1.5V silver oxide battery, ensuring correct polarity.
- Close the battery compartment cover securely.
4.3 Initial Cleaning
Before first use, wipe the caliper's main scale (ruler body) with a clean, dry cloth. Ensure no liquid substances enter the slider frame to prevent damage to electronic components.
5. Operating Instructions
5.1 Power On/Off
Press the ON/OFF button (6) to power the caliper on or off.
5.2 Unit Conversion
Press the mm/in button (4) to switch between millimeter (mm) and inch (in) measurement units.
5.3 Zero Setting

- Absolute Measurement (ORIGIN): Close the jaws completely and press the ORIGIN button (5). This sets the absolute zero point, and all subsequent measurements will be relative to this fixed origin. The caliper retains this origin even when powered off.
- Incremental Measurement (ZERO): Close the jaws completely (or set them to any desired reference point) and press the ZERO button (7). The display will show 0.00. All subsequent measurements will be relative to this temporary zero point.
5.4 Taking Measurements
Ensure the measuring surfaces are clean before taking a measurement.
- External Measurement: Use the outer jaws (2). Open the jaws, place the workpiece between them, and close until snug. Read the value on the digital display.
- Internal Measurement: Use the inner jaws (1). Insert the inner jaws into the feature to be measured and open them until they contact the surfaces. Read the value.
- Depth Measurement: Use the depth rod (11). Place the end of the ruler body on the top surface and extend the depth rod until it touches the bottom of the hole or step. Read the value.
- Step Measurement: Use the step measuring face (12). Place the step face against the higher surface and extend the slider until the end of the main scale touches the lower surface. Read the value.
For precise positioning, use the thumb roller (10) to make fine adjustments. Once the measurement is taken, you can use the tightening screw (3) to lock the slider in place for easier reading.
6. Maintenance
6.1 Cleaning
- Keep the caliper's main scale clean. Avoid any liquids, especially water, from entering the slider frame to prevent damage to electronic components.
- The caliper surface can be cleaned with clean gasoline. Do NOT use acetone or alcohol, as these may damage the surface.
6.2 Battery Replacement
When the battery voltage is low (indicated by a jumping display or no display), replace the battery as described in Section 4.2. A single 1.5V silver oxide battery typically lasts for 12 months of continuous use.
6.3 Data Output Port
If the data output port (part of item 9 in Figure 2) is not in use, do not remove its cover to prevent damage to the electronic components. The port supports RS-232 data output and can be connected to a computer or printer via a dedicated interface.

Always store the caliper in its protective case when not in use to prevent damage.
7. Troubleshooting
Refer to the table below for common issues and their remedies:
| Phenomenon | Cause | Remedy |
|---|---|---|
| Five-digit display jumps simultaneously, approx. once per second. | Battery voltage below 1.45V. | Remove the frame, replace the battery. |
| Display cannot count. | Accidental circuit malfunction. | Remove the battery, wait 30 seconds, then reinstall. |
| Displays only 000.00 or IN000.00. | Two function buttons and moving scale signal terminal short-circuited. | Remove the frame, adjust button springs to ideal state. |
| Function button does not work. | Button spring deformed due to excessive force. | Remove the frame, adjust button springs to ideal state. |
| LCD screen no display. | 1. Battery contact poor. 2. Battery voltage below 1.1V. | 1. Remove the frame, ensure good battery contact. 2. Replace the battery. |
8. User Tips
No specific user tips were available from the provided data. Always ensure the caliper is clean and properly zeroed before taking critical measurements.
9. Warranty and Support
For detailed warranty information and technical support, please refer to the official Mitutoyo documentation or contact your local Mitutoyo distributor. A comprehensive user manual in PDF format is available for download: