1. Introduction
Thank you for purchasing your Annke 8MP Wireless CCTV System. This manual provides detailed instructions for the installation, operation, and maintenance of your security system. Please read this manual carefully before use to ensure proper setup and functionality. For any questions, please contact our support team.
1.1 Safety Instructions
These instructions are provided to ensure correct product usage and to prevent danger or property loss. Please observe all warnings and cautions.
- Warnings: Serious injury or death may occur if any warnings are neglected.
- Cautions: Injury or equipment damage may occur if any cautions are neglected.
⚠️ Warnings
Follow these safeguards to prevent serious injury or death.
⚠️ Cautions
Follow these precautions to prevent potential injury or material damage.
General Warnings:
- Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
- Always comply with local and national electrical safety regulations.
- Input voltage must meet SELV (Safety Extra Low Voltage) and Limited Power Source standards (100 to 240 VAC or 12 VDC).
- Do not connect multiple devices to a single power adapter to avoid overload and fire hazards.
- Ensure the power plug is firmly connected.
- If smoke, odor, or unusual noise occurs, immediately power off, unplug, and contact customer service.
Prevention and Warning Tips:
- Only qualified personnel should perform installation and maintenance.
- Install equipment away from children and the elderly to prevent electrical injury.
- Ensure safe electricity use to prevent fire from current overload.
- The NVR is for indoor use only. Install in a well-ventilated, dust-free environment, away from liquids.
- Cameras are dustproof and waterproof (IP66) for outdoor use. Securely fix them to prevent falling.
- Ensure waterproof connections for camera cables.
- Power off devices before connecting/disconnecting accessories to prevent damage.
- Use hard disks recommended by the factory for optimal performance.
2. Package Contents
Your Annke 8MP Wireless CCTV System package typically includes:
- 1 x 16-Channel Wireless NVR (Network Video Recorder)
- 2/4/6 x 8MP Wireless IP Cameras (quantity depends on kit purchased)
- Power Adapters for NVR and Cameras
- USB Mouse
- Ethernet Cable
- Mounting Screw Kits
- Quick Start Guide
Note: Specific contents may vary slightly based on the purchased kit configuration.
3. System Setup
3.1 Connection Diagram
Follow the diagram below to connect your NVR and cameras. Ensure all components are powered correctly.

Basic Connections:
- Connect the NVR to a power outlet using its power adapter.
- Connect the NVR to a monitor (VGA or HDMI) to view the interface.
- (Optional) Connect the NVR to your router via an Ethernet cable for internet access and remote viewing.
- Connect each camera to its respective power adapter and plug into a power outlet.
- The cameras will automatically connect to the NVR wirelessly once powered on.
3.2 Adding Cameras (Applicable to N48WHR)
If you need to add new cameras or re-add existing ones, follow these steps:
- Ensure the NVR has an available channel.
- Power on the camera and wait for it to fully start up.
- Right-click on the NVR interface with the mouse and select [Wireless Add].
- The NVR will automatically search for and add nearby cameras.
- Click [Exit] once all desired cameras are added.
Troubleshooting Camera Addition:
- If a camera is not found, try resetting the camera and repeating the process.
- Alternatively, connect the camera directly to the NVR using an Ethernet cable and then attempt to add it.
3.3 Camera Installation
Annke cameras are designed for both indoor and outdoor use with an IP66 weatherproof rating.


Installation Tips:
- Mount cameras securely using the provided 3-axis mounting bracket.
- Ensure the camera's field of view covers the desired area.
- For outdoor installations, ensure all cable connections are waterproofed.
- Position cameras to optimize WiFi signal strength.
4. System Operation
4.1 Product Overview Video
Video 4.1: Annke 16CH Wireless Security Camera System Overview
4.2 Live View and Playback
- Access live camera feeds directly from the NVR connected to a monitor.
- Use the NVR interface to select specific cameras or view multiple cameras simultaneously.
- Review recorded footage using the playback function.
4.3 Two-Way Audio
Each camera is equipped with a built-in microphone and speaker, enabling two-way audio communication.

How to Use:
- From the NVR interface or the Annke Sight mobile app, select the camera you wish to communicate through.
- Activate the microphone and speaker functions to talk and listen in real-time.
4.4 Human Detection & Alerts
The system features smart human detection to minimize false alarms caused by pets or other moving objects.
- When human motion is detected, the system can send instant push notifications to your mobile device via the Annke Sight app.
- Configure alert settings, including detection zones and sensitivity, through the NVR menu or mobile app.
4.5 Smart Search & Playback
Efficiently find specific events in your recorded footage.

- Access the Smart Search feature from the NVR menu.
- Filter recordings by event type, such as