JDiag M100 Pro

Contents

JDiag M100 Pro OBD2 Motorcycle Scanner User Manual

Model: M100 Pro

1. Introduction

The JDiag M100 Pro Moto Scanner is a new generation handheld motorcycle diagnostic tool designed to cover virtually all major manufacturers' diagnostic functions. It assists technicians in diagnosing problems and performing repairs faster. Many common procedures are integrated into the tool, guiding the technician through tasks such as injector adjustments, CO trimmer settings, throttle valve position sensor (TPS) adjustments, auto-adaptive parameter resets, and idling adjustments.

This tool provides live data, displays ECU data, reads stored fault codes (history), and shows live data parameters like RPM, battery voltage, and throttle angle.

The JDiag M100 Pro supports a wide range of motorcycle brands including AEON, APRILIA, BENELLI, BMW, Hartford, HONDA, KAWASAKI, KTM, KYMCO, PIAGGIO, PGO, SUZUKI, SYM, VESPA, YAMAHA, and generic OBDII. It also supports multiple languages: English, Chinese, Thai, Indonesian, Vietnamese, Spanish, Russian, Italian, Cambodian, Turkish, Portuguese, Japanese, Korean, and German.

JDiag M100 Pro scanner with carrying case, highlighting Battery Test, Clear Fault Codes, Motorcycle Scanner.

Figure 1: JDiag M100 Pro Motorcycle Scanner and its key features.

2. Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the scan tool, carefully read this user manual and observe the following safety precautions at a minimum whenever working on a vehicle:

  • Always perform automotive testing in a safe environment.
  • Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool can cause driver distraction and lead to accidents.
  • Wear safety eye protection that meets ANSI standards.
  • Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
  • Operate the vehicle in a well-ventilated work area. Exhaust gases are poisonous.
  • Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
  • Use extreme caution when working around the ignition coil, distributor cap, ignition wires, and spark plugs. These components create hazardous voltages when the engine is running.
  • Put the transmission in P (for A/T) or N (M/T) and ensure the parking brake is engaged.
  • Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
  • Do not connect or disconnect any test equipment while the ignition is ON or the engine is running.
  • Keep the scan tool dry, clean, and free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the scan tool when necessary.
  • The manufacturer is not responsible for any damage caused by unintentional or deliberate misuse of its products or tools.

3. Specifications and Parameters

Feature Specification
Display 3.5 inches (480*320 DPI) TFT true color display
Working Temperature 0-60°C (32-140°F)
Storage Temperature -40-70°C (-40-185°F)
External Power Supply 9-18V
Communication Interface OBD-II
Software Update Yes
Item Weight 1.3kg
Item Height 8.2cm
Item Width 25cm
Item Length 18.2cm
Material ABS
Certifications CE, RoHS, FCC
Supported Languages English, Italian, Chinese Traditional, Spanish, French, Cambodian, Thai, Turkish, Vietnamese, Indonesian, Portuguese, Japanese, Korean, German, Russian

4. Package Contents

The JDiag M100 Pro Basic Version includes the following items:

  • JDiag M100 Pro Scanner Unit
  • Carton Packaging
  • Tool Box
  • User's Manual (Printed)
  • Main Test Cable (MOTO-01)
  • Power Clamp Supply Battery Test Cable (MOTO-02)
  • OBD-16P Cable (MOTO-03)
  • Universal Jump Cable (MOTO-04)
  • Mini USB Cable
JDiag M100 Pro Basic Version package contents, including the scanner, carton, tool box, user manual, main test cable (MOTO-01), power clamp supply battery test cable (MOTO-02), OBD-16P cable (MOTO-03), universal jump cable (MOTO-04), and Mini USB cable.

Figure 2: JDiag M100 Pro Basic Version Package Contents.

5. Setup and Connection

5.1 Connecting the M100 Pro

  1. Turn the motorcycle ignition ON.
  2. Locate the Motorcycle Data Link Connector (DLC) on your vehicle.
  3. Connect the appropriate test cable (e.g., MOTO-01, MOTO-03) from the M100 Pro to the motorcycle's DLC.

5.2 Tool Description

Familiarize yourself with the scanner's interface and buttons:

JDiag M100 Pro scanner displaying diagnostic functions like Read system information, Read data stream, Read fault code, Erase fault code, Freeze data, Battery life detection, Actuators test, CO idle speed adjustment, Troubleshooting guidance.

Figure 3: JDiag M100 Pro Interface and Functions.

  • LCD Display: Displays menus and test results.
  • ESC Button: Returns to the previous menu.
  • Up Scroll Button: Moves the cursor up for selection.
  • Left Scroll Button: Moves the cursor left for selection or turns the page up when more than one page is displayed.
  • F1 Button: Provides help information and Code Breaker function.
  • Help Button (H/?): Provides help information function.
  • Right Scroll Button: Moves the cursor right for selection, or turns the page down when more than one page is displayed.
  • Down Scroll Button: Moves the cursor down for selection.
  • F2 Button: Backspace function.
  • F1 + F2: Press both buttons together to perform a screen capture.
  • OBDII Connector: Connects the scan tool to the vehicle's data link connector (DLC).

6. Operating Modes

6.1 Diagnosis Mode

This mode allows you to read and clear fault codes, view live data, and access ECU information.

  1. From the main menu, select [Diagnosis] and press [OK].
  2. Select the motorcycle brand (e.g., AEON, Honda, Kawasaki, KTM, Yamaha, BMW) from the list and press [OK].
  3. The screen will display options such as ECU Information, Engine Data, Live Data, Read Fault Code, and Erase Fault Code.

6.1.1 ECU Information

To view ECU information, select [ECU Information] and press [OK]. The screen will display details like Software End Model, Hardware Base Model, Soft. Calibration P/N, and KYSYST MainSW_Cal_ID.

6.1.2 Engine Data (Live Data)

Current data provides numeric figures of the working status for the motor engine, helping to determine if the motor is functioning normally. To view, select [Engine Data] and press [OK].

In this display, you can press [YES] to enter the waveform function, which displays numerical changes of the selected item over time.

6.1.3 Read Fault Code

To read fault codes, select [Read Fault Code] and press [OK]. The screen will display options for Current Fault Code, History Codes, and Pending Codes. Select [Current Fault Code] and press [OK] to view active Diagnostic Trouble Codes (DTCs).

6.1.4 Erase Fault Code

To erase fault codes, select [Erase Fault Code] and press [OK]. A confirmation prompt will appear. Note: Before erasing fault codes, ensure the ignition is ON but the engine is not running. Press [YES] to confirm and erase fault codes.

6.2 Battery Test Mode

The M100 Pro includes a professional battery tester for 12V batteries, cranking, and charging systems. It measures resistance and voltage to provide accurate test results.

Why Battery Voltage is Important: Your motorcycle battery provides electrical needs when the engine isn't running and supplies the necessary spark for starting. Regular checks prevent unexpected breakdowns.

JDiag M100 Pro scanner displaying multiple battery test methods: Quick Test, Standard Test, Start Test, Charge Test, Wave Test.

Figure 4: Battery Test Options.

6.2.1 Connecting for Battery Test

Connect the Red Clip to the battery Positive (+) pole and the Black Clip to the battery Negative (-) pole. The device will power up automatically.

  • Note 1: The device will not work properly if the battery voltage is under 7V.
  • Note 2: If testing the battery on the vehicle, do not insert the key or keep it in the OFF position. Ensure all electrical devices and doors are closed.

6.2.2 Standard Test

  1. From the main menu, select [Battery] and press [OK].
  2. Select [Standard] to perform a Battery Test and press [OK].
  3. Select whether the battery is [In-Vehicle] or [Out-Of-Vehicle] and press [OK].
  4. Select the correct battery type (e.g., Regular Flooded, AGM Flat Plate, AGM Spiral, GEL, EFB) and press [OK].
  5. Input the correct CCA (Cold Cranking Amps) values using the arrow keys. This information is usually labeled on the battery. Press [OK].
  6. The test result will display Real Voltage, Rated CCA value, Measured CCA value, Resistance Value, State of Health (SOH), and State of Charge (SOC).

6.2.3 Cranking Test

This test measures the battery's ability to crank the engine.

  1. From the main menu, select [Battery], then [Start] and press [OK].
  2. Turn the ignition key ON to start the engine.
  3. The test result will display Minimum Start Voltage, Maximum Start Voltage, and Real Voltage.

6.2.4 Charge Test

This test evaluates the charging system of the motorcycle.

  1. From the main menu, select [Battery], then [Charge] and press [OK].
  2. Follow the on-screen instructions:
    • Turn on the light for 3 seconds during testing.
    • Get the engine speed to 2000 RPM and keep it for 3 seconds.
    • Press [Enter].
  3. The test will display Load Voltage, No-Load Voltage, Diodes Ripple Voltage, and Charge Voltage Status.

6.2.5 Wave Test

To perform battery voltage monitoring, select [Wave Test] from the battery menu. This will display the battery voltage as a waveform.

6.3 Module Test

This mode allows you to test various components of the scanner itself.

  1. From the main menu, select [Module Test] and press [OK].
  2. Choose from the following options:
    • LCD Test: Checks the display for proper color rendering (red, blue, green).
    • Keypad Test: Verifies the functionality of each button. Press [ESC] twice to quit.
    • SD Card Test: Checks if the SD card is properly inserted and can read/write data.
    • Version: Displays the software and hardware versions of the device.

6.4 USB Memory

To access stored data, select [USB Memory] and press [OK]. Connect the device to a computer via the USB cable. The computer will automatically detect the device's storage.

6.5 Image (Screenshot Function)

The M100 Pro allows you to capture screenshots of the display.

  • To take a screenshot, press F1 + F2 simultaneously.
  • To view or delete captured images, select [Image] from the main menu and press [OK]. Options include [SHOW IMAGE] and [DELETE IMAGE].

6.6 Setup

The setup menu allows you to configure various settings for the device.

  1. From the main menu, select [Setup] and press [OK].
  2. Options include [SOUND] and [LANGUAGE].
  3. To change the language, select [LANGUAGE] and press [OK]. Choose your desired language from the list (e.g., English, Spanish, French, etc.) and press [OK].

6.7 Print Function

You can print test results by connecting the M100 Pro to a computer.

  1. Connect the device to your PC with the USB cable.
  2. Select [Setup] from the main menu, then navigate to [USB Storage]. This will indicate a successful connection to the device's TF Storage Card.
  3. Select the picture of the TEST RESULT from the SNAP folder on the device's TF Storage Card to perform printing.

7. Maintenance

  • Cleaning: Keep the scan tool dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the scan tool when necessary.
  • Software Updates: The M100 Pro supports software updates. This function allows you to update the scan tool software and DTC Library through a computer.

7.1 Software Update Procedure

To update your scan tool, you will need the following items:

  • JDiag M100 Pro Scan Tool
  • PC or Laptop with USB port
  • USB Cable

Upgrade Steps:

  1. Download the upgrade file from the official JDiag website (www.jdiagtool.com).
  2. Connect the device to your computer via the USB cable.
  3. Enter [OK] on the scanner and select [USB Storage].
  4. Copy the downloaded upgrade files to the correct folder in the device's TF Storage Card.

Video 1: Demonstration of JDiag M100 Pro unboxing and basic menu navigation.

8. Troubleshooting

The JDiag M100 Pro is designed to help diagnose common motorcycle issues. If you encounter problems with your motorcycle, the following functions can assist:

  • Read Fault Code: Use this function to identify specific Diagnostic Trouble Codes (DTCs) that indicate system malfunctions.
  • Erase Fault Code: After addressing a fault, use this function to clear the stored codes from the ECU.
  • Live Data: Monitor real-time engine parameters to observe system behavior and identify anomalies.
  • Battery Test: Perform Quick, Standard, Cranking, Charge, and Wave tests to assess the health and performance of your motorcycle's battery and charging system.
  • Troubleshooting Guidance: The device includes built-in guidance for common issues.
Three images depicting common motorcycle issues: frequent failures, broken down midway, and expensive 4S maintenance.

Figure 5: Common motorcycle issues that the M100 Pro can help diagnose.

9. User Tips

  • Regular Updates: Keep your M100 Pro software updated to ensure compatibility with the latest motorcycle models and access to new features. Refer to the "Software Update Procedure" in the Maintenance section.
  • Battery Health: Perform battery tests regularly, especially before long rides or after periods of inactivity, to ensure optimal battery performance and prevent starting issues.
  • Language Settings: If the device displays an unfamiliar language, navigate to the "Setup" menu and select "LANGUAGE" to switch to your preferred language.
  • Screenshot Feature: Utilize the F1+F2 shortcut to capture screenshots of diagnostic results for documentation or sharing.

10. Warranty and Support

10.1 One-Year Warranty

JDiag Technology provides a 1-year warranty from the date of original purchase, provided the product is purchased from an official channel and meets the following conditions:

  • The warranty is limited to repairing or replacing new equipment, without additional cost. Proof of purchase (sales invoices or copies) is required.
  • The warranty does not cover unauthorized disassembly, damage due to flooding, lightning strikes, or repairs by unauthorized shops. Damage caused by improper use is also not covered.
  • JDiag Technology is not responsible for damages caused by use, misuse, or improper installation and testing.
  • All information in this manual is based on the latest available information at the time of publication. JDiag Technology reserves the right to make changes at any time without notice regarding accuracy or completeness.

10.2 Service Process

For any questions regarding the use of this product, please contact your local authorized dealer directly or visit the official JDiag website for consultation.

If you need to repair or return goods, contact the distributor or the sales representatives who assisted you.

JDiag Electronics Technology Co.,Ltd. Contact Information:

  • Email: info@jdiagtool.com
  • Tel: +86-755-21005135
  • Web: www.jdiagtool.com
  • Address: 3rd Floor, B2.Jindida Science Park, Langkou Community, Dalang Street, Longhua District, Shenzhen, China

A PDF version of this user manual is available for download from the official JDiag website: User Manual (PDF).


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.