1. Introduction
The Retevis MateTalk C66B is a versatile UHF/VHF walkie talkie designed for long-range communication with features like Type-C fast charging, dual-band dual-standby, and clear audio. It is suitable for various applications including outdoor activities, hotel management, restaurant operations, and farm communication.

2. Safety Information
RF Energy Exposure and Product Safety Guide
Before using this device, please read this guide which contains important operating instructions for safe usage, control information and operational instructions for compliance with RF Energy Exposure limits in applicable national and international standards.
User's instructions should accompany the device when transferred to other users. Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority granted by the local government radio management departments to operate this radio and should not be made.
Hand-held Mode
To control your exposure and ensure compliance with the controlled environment exposure limits, always adhere to the following procedure:
- To receive calls, release the PTT key.
- To transmit (talk), press the Push-to-Talk (PTT) key in front of the face.
- Hold the radio in a vertical position with the microphone (and other parts of the radio including the antenna) at least one inch (2.5 centimeters) away from the nose or lips.
Medical Devices
Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. During transmissions, your radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so, such as hospitals or healthcare facilities.
Persons with pacemakers, implantable cardioverter defibrillators (ICDs) or other active implantable medical devices should:
- Consult with their physicians regarding the potential risk of interference from radio frequency transmitters.
- Turn the radio OFF immediately if there is any reason to suspect that interference is taking place.
- Do not carry the radio in a chest pocket or near the implantation site, and carry or use the radio on the opposite side of the body from the implantable device to minimize the potential for interference.
Hearing Protection
Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio's volume, the less time is required before your hearing could be affected.
- Use the lowest volume necessary to do your job.
- Limit the amount of time you use headsets or earpieces at high volume.
- When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear.
Choking Hazard
WARNING: CHOKING HAZARD - Small Parts. Not suitable for children under 3 years old.

3. Package Contents
Please inspect the contents of the packaging box in detail before use. If any items are missing or damaged, please contact your dealer immediately.

Standard Package Includes:
- Retevis MateTalk C66B Walkie Talkie: 1 unit
- Base Charger: 1 unit
- Belt Clip: 1 unit
- Handstrap: 1 unit
- Type-C Charging Cable: 1 unit
- User Manual (PDF): 1 unit (available for download at PDF Link)
4. Product Overview
Physical Components

| No. | Name | Purpose |
|---|---|---|
| 1 | Antenna | Transmit and receive signals (detachable) |
| 2 | Indicator Light | Indicate working status |
| 3 | Power Switch | Power on/off and volume adjustment |
| 4 | PTT | Transmit voice |
| 5 | Speaker | Voice output |
| 6 | Mic | Voice input |
| 7 | Up key | Menu navigation, channel adjustment |
| 8 | MENU | Opens menu/confirm |
| 9 | LCD Screen | Displays channel, status, battery level, etc. |
| 10 | Channel Switch | Switch channels |
| 11 | SK1 | Long press: Alarm; Short press: Power switch |
| 12 | SK2 | Long press: Reverse; Short press: Scan |
| 13 | Typec Interface | Charging |
| 14 | Earphone Jack | Earphone/Programming |
| 15 | P1 | Long press: Offline; Short press: Monitor |
| 16 | Down key | Menu navigation, channel adjustment |
| 17 | P2 | Long press: VOX; Short press: Monitor |
| 18 | EXIT | Return/region selection |
LCD Display Indicators

| No. | Location | Product Status |
|---|---|---|
| 1 | T | Channel strength indicator; more bars indicate a stronger signal |
| 2 | Hi | Current transmit power is high (longest communication distance, highest power consumption) |
| Lo | Current transmit power is low (most power-efficient, shorter distance) | |
| 3 | DCS | Indicate the current DCS is digital |
| CT | Indicate the current CTCSS is analog | |
| 4 | + | In frequency mode, indicate that the transmit frequency is the receive frequency plus a frequency difference |
| − | In frequency mode, indicate that the transmit frequency is the receive frequency minus a frequency difference | |
| 5 | D | Indicate dual-frequency standby is enabled; can simultaneously stand by on two frequency bands displayed on the screen |
| 6 | Appear when the keyboard is locked; press and hold the # key to unlock | |
| 7 | Ψ | Indicate that VOX transmission is enabled; transmission starts when the microphone's sound pressure level reaches the set value |
| 8 | R | Indicate that the receive and transmit frequencies are inverted in frequency/channel mode |
| 9 | N | Appear when the channel operates in narrowband mode |
| 10 | Display current battery level; more bars indicate a higher battery level | |
| 11 | Δ/▼ | Frequency band pointer, indicates current operation on the main channel |
| 12 | Number | In channel mode, channel number for frequency band A |
| 13 | Number | In channel mode, channel number for frequency band B |
5. Installation
5.1 Installing/Removing the Battery
- Align the positioning post at the bottom of the battery pack with the battery slot on the back cover.
- Gently press down on the top of the battery to snap it into place. The battery lock will naturally slide down to secure the battery pack.
- To remove the battery, slide the lock upward to release it.
5.2 Installing/Removing the Antenna
- Hold the bottom of the antenna and screw it clockwise into the antenna socket on top of the walkie-talkie until tight.
- To remove the antenna, turn it counterclockwise.
5.3 Installing/Removing the Belt Clip
If necessary, attach the provided belt clip to the screw hole on the back of the battery pack for convenient carrying. To remove the belt clip, simply unscrew the two screws.
5.4 Installing the Walkie-Talkie Lanyard
Thread the walkie-talkie lanyard through the ring in the middle of the walkie-talkie.
5.5 Installing the Optional Speaker/Microphone Headset
Lift the earphone cover and plug the speaker/microphone headset into the appropriate jack.
6. Charging
6.1 Charging Precautions
- Charge new or long-unused rechargeable batteries before use. Two or three charge/discharge cycles will help the battery reach its optimal capacity.
- Use only batteries specified by our company. Using other batteries may cause explosions and result in personal injury.
- Do not short-circuit battery terminals or dispose of batteries in a fire.
- Charge batteries in an environment where the temperature is between 0°C and 40°C.
- Turn off the power of the walkie-talkie with the installed battery during charging.
- Avoid unplugging the power or battery during the entire charging process.
- If the usage time significantly decreases even after full charging, replace with a new battery.
- Do not charge the battery or walkie-talkie when they are wet.
- Keep away from flammable materials, heat sources, and ignition sources while charging.
- Do not charge the battery for more than 3 hours. Disconnect the charger when the device is fully charged.
6.2 Charging Steps
- Insert the adapter with a standard output of 5V DC and 2A into a power socket.
- Place the battery or the walkie-talkie with the installed battery onto the charging dock. Ensure good contact. The charger indicator turns red for charging, green for full charge.
- For Type-C charging, insert the Type-C charging cable into the port on the right side of the device. A green icon on the device indicates a full charge.
Note: Do not use the walkie-talkie during charging and ensure it is turned off.


7. Basic Operations
7.1 Power On/Off
To turn on the walkie-talkie, rotate the 【Power/Volume Switch】 knob clockwise until you hear a "click" and a short beep. To turn off, rotate the knob counterclockwise until you hear a "click."
7.2 Volume Adjustment
Turn the 【Power/Volume Switch】 knob clockwise to increase the voice reception volume and counterclockwise to decrease it.
7.3 Switching Main/Sub Frequency Bands
In standby mode, short press the 【MENU】 key to switch between A and B bands, indicated by (→). The band where (→) appears is the main frequency band.
7.4 Channel Selection
In channel mode, select channels:
- Method 1: Press the ▲/▼ key directly to select channels upward or downward. Long press for rapid channel switching.
- Method 2: Manually enter the channel number to directly access that channel.
7.5 Initiating/Receiving Calls
- Maintain a distance of 2.5 cm to 5 cm between the microphone and your mouth for optimal reception volume during transmission.
- After selecting a channel, press and hold the 【PTT】 key to transmit. The red indicator light stays on.
- Release the 【PTT】 key to enter receive mode. The green indicator light stays on.
8. Menu Usage and Functions
To enter the menu, press the 【MENU】 key in standby mode. Use ▲/▼ to navigate and 【MENU】 again to select. Use ▲/▼ to adjust parameters and 【MENU】 to save, or 【EXIT】 to cancel.
Key Functions:
- Squelch Level (00): Adjusts the signal strength required to activate audio output (0-9). Default is 3.
- Transmit Power (01): Selects between High Power (5W) and Low Power (0.5W).
- Power Saving Mode (02): Enables/disables automatic power-saving after 10 seconds of inactivity.
- VOX Transmission (03): Enables voice-activated transmission. Set sensitivity from 1-10.
- Channel Bandwidth (04): Selects Wideband or Narrowband operation.
- Backlight (05): Sets backlight behavior (Always On, Off, or timed options from 5-60 seconds).
- Menu Exit Time (06): Sets the time for the menu to automatically exit (5-60 seconds).
- Dual Frequency Dual Standby (07): Enables/disables simultaneous monitoring of two channels.
- Beep Prompt (08): Toggles key press tone feedback.
- Voice Prompt (09): Toggles voice prompts for operations.
- TOT (TX Over Time) (10): Limits continuous transmission time (15-300 seconds).
- Receive DCS (11) / Receive CTCSS (12) / Transmit DCS (13) / Transmit CTCSS (14): Sets specific codes for signal filtering. Refer to the CTC and DCS Lists for values.
- Tone (15): Sets single-tone signaling for repeater activation (1000Hz, 1450Hz, 1750Hz, 2100Hz).
- Scan Mode (16): Configures channel scanning behavior (Time, Carrier, Search).
- Display Mode (17/18): Sets whether to display frequency or channel name for A/B segments.
- Busy Lockout (19): Prevents transmission when the channel is occupied.
- Key Auto Lock (20): Automatically locks keys after inactivity.
- Shortcut Functions (21-28): Assigns functions (Alarm, Scan, Monitor, VOX, Power Adjustment, etc.) to SK1, SK2, P1, P2 buttons for short or long presses.
- Alarm Modes (29): Sets alarm type (Local Alarm, Send Alarm Sound, Send Alarm Code).
- Tail Tone Elimination (30): Suppresses noise at the end of transmission.
- Roger Beep (31): Emits a tone when PTT is released.
- End of Transmission Tone (32): Toggles a tone at the end of transmission.
- Factory Reset (33): Resets menu settings or all settings to default.
- Special DCS (34): Allows communication only with devices using the same DCS code.
- Voice Encryption (35): Scrambles voice signals for private communication.
- Compander (36): Enhances voice clarity by compressing loud sounds.
- Channel Deletion (37): Deletes specified channel settings.
- One-Key Pairing Function (28): Long-press 【MENU】 + (*) to enable one-touch frequency matching.
- Wireless Cloning (29): Allows cloning settings between devices.
- One-Key CTCSS/DCS Disable (30): Quickly disables current CTCSS/DCS settings.
- TYPE-C Charging Function (31): Describes charging via Type-C port.




9. Maintenance and Cleaning
- Do not hold the antenna or external microphone directly.
- Use a lint-free cloth to wipe dust and stains off the walkie-talkie to prevent poor contact.
- Cover the earphone jack when the walkie-talkie is not in use.
- After prolonged use, clean keys, control knobs, and casing with a neutral detergent and a damp cloth. Avoid strong corrosive chemicals.
10. Troubleshooting
- Battery Life Significantly Decreases: If the usage time significantly decreases even after full charging, it indicates that the battery life has ended. Replace with a new battery.
- Charging Issues: Ensure the walkie-talkie is turned off during charging. Avoid unplugging the power or battery during the charging process. Do not charge wet batteries.
- Interference: Ensure proper antenna installation. If experiencing interference, check for nearby electronic devices or turn off the radio in sensitive areas.
- Communication Range Issues: Ensure the transmit power is set to 'Hi' for maximum range. Check for obstructions and environmental factors.
- No Audio/Poor Audio: Adjust the squelch level. A lower squelch level allows more background noise but increases communication distance. A higher squelch level requires stronger signals for clearer audio. Ensure the speaker is not blocked.
11. Specifications
| Attribute | Value |
|---|---|
| Channels | 16 (default) |
| Operating Voltage | DC 7.4V |
| Operating Temperature | -20°C ~ +50°C |
| Operating Mode | Single-Frequency Simplex |
| Attribute | Value |
|---|---|
| Output Power | High Power: 5W; Low Power: 0.5W |
| Adjacent Channel Power | ≤-65dB |
| Transmit Current | ≤1.7A |
| Modulation Mode | FM |
| Modulation Sensitivity | 8~12mV |
| Attribute | Value |
|---|---|
| Sensitivity | -122dBm (12dB SINAD) |
| Antenna Impedance | 50Ω |
| Audio Distortion | <5% |
| Receive Current | ≤0.5A |
Factory Default Frequencies
| Channel | Frequency | CTCSS/DCS | Power Setting |
|---|---|---|---|
| 1 | 461.11250 | 67 | Default: High power, adjustable high/low |
| 2 | 461.13750 | 67 | Default: High power, adjustable high/low |
| 3 | 459.60625 | 94.8 | Default: High power, adjustable high/low |
| 4 | 449.31250 | 94.8 | Default: High power, adjustable high/low |
| 5 | 459.12500 | 136.5 | Default: High power, adjustable high/low |
| 6 | 444.55000 | 136.5 | Default: High power, adjustable high/low |
| 7 | 457.17500 | 136.5 | Default: High power, adjustable high/low |
| 8 | 442.87500 | 136.5 | Default: High power, adjustable high/low |
| 9 | 151.62500 | 67 | Default: High power, adjustable high/low |
| 10 | 151.95500 | 67 | Default: High power, adjustable high/low |
| 11 | 154.41000 | 94.8 | Default: High power, adjustable high/low |
| 12 | 164.05000 | 94.8 | Default: High power, adjustable high/low |
| 13 | 146.25000 | 136.5 | Default: High power, adjustable high/low |
| 14 | 155.60000 | 136.5 | Default: High power, adjustable high/low |
| 15 | 154.98750 | 136.5 | Default: High power, adjustable high/low |
| 16 | 156.30000 | 136.5 | Default: High power, adjustable high/low |
Note: Frequency range may vary by device type and local regulations. For business use, ensure compliance with local rules and obtain necessary licenses. Consult your dealer or system administrator for more information.
12. User Tips
- Programming Channels: While the device offers one-key pairing for quick frequency matching, for advanced customization or to set specific channel names, you may need to use programming software. Refer to the official Retevis website for software and firmware downloads.
- Optimizing Battery Life: To maximize battery longevity, perform two or three charge/discharge cycles when the battery is new or has been unused for a long time. Avoid overcharging and always disconnect the charger once the device is fully charged.
- Clear Communication in Noisy Environments: Utilize the 1W speaker and adjust the squelch levels (0-9) to optimize audio clarity. A higher squelch level can reduce background noise, while a lower level might extend range in quieter settings.
- Hands-Free Operation: The VOX function is excellent for situations where your hands are occupied. Adjust the VOX sensitivity (1-10) to ensure reliable voice activation without accidental transmissions.
13. Warranty and Support
Guarantee Information
Most new products carry a two-year manufacturer's warranty from the date of purchase.
For warranty service, you will need to provide proof of purchase from the original seller for verification.
Authorized Accessories List
For a list of Retevis-approved accessories for your radio model, visit the website: www.Retevis.com
Contact Retevis for assistance regarding repairs and service.
EU Representative Information
Germany Retevis Technology GmbH
Uetzenäcker 29, 38176 Wendeburg
Email: Retevis-Europa@outlook.com
Tel: +0049 053029369179
For downloading further resources (Brochures, Software/Firmware, Manual etc.), please contact your direct reseller first OR go to website retevis.com and check "support" in the each product link to download it.