KKMOON FBT200

Contents

KKMOON FBT200 Car Battery Tester & Analyzer User Manual

Model: FBT200

1. Introduction

The KKMOON FBT200 is a smart battery tester and analyzer designed for automotive 12V and 24V lead-acid batteries. This device provides quick and accurate test results, allowing you to monitor your battery's health, state of charge, voltage, internal resistance, and Cold Cranking Amps (CCA) value.

It supports various battery types including regular flooded, AGM flat plate, AGM spiral, and GEL batteries, making it suitable for cars, SUVs, light trucks, and motorcycles. The FBT200 delivers precise readings in just 3 seconds based on SAE, DIN, IEC, EN, CA, and JIS standards.

Note: This device cannot test lithium batteries.

Front view of the FBT200 battery tester

Figure 1: KKMOON FBT200 Battery Tester Front View

2. Package Contents

Please check the package for the following items:

  • 1 x FBT200 Battery Tester with integrated cable and clamps
  • 1 x User Manual
  • 1 x Storage Pouch
Contents of the FBT200 package

Figure 2: Package Contents

3. Setup

  1. Ensure the battery terminals are clean and free from corrosion for accurate readings.
  2. Connect the red clamp of the FBT200 tester to the positive (+) terminal of the battery.
  3. Connect the black clamp of the FBT200 tester to the negative (-) terminal of the battery.
  4. Ensure both clamps are securely attached to prevent intermittent connections. The device will power on automatically once connected.
FBT200 battery tester connected to a car battery

Figure 3: Tester Connected to a Car Battery

4. Operating Instructions

4.1. Basic Operation

Once connected to the battery, the FBT200 will power on and display the main menu or initial test screen. Use the navigation buttons (Up/Down arrows) to scroll through options, the ENTER button to select, ESC to go back, and RESET to restart a test or clear settings.

Close-up front view of the FBT200 battery tester showing buttons

Figure 4: Tester Control Buttons

4.2. Performing a Test

The FBT200 automatically performs a comprehensive analysis of the connected battery. Key parameters are displayed within 3 seconds.

4.3. Understanding Test Results

The tester provides various diagnostic parameters to assess battery condition:

  • Internal Resistance (IR): Indicates the battery's ability to deliver current. Lower values are better.
  • Battery Voltage (VOLT): The current voltage of the battery.
  • CCA Value (EDC): Cold Cranking Amps, a measure of the battery's ability to start an engine in cold temperatures.
  • Status of Charge (SOC): The current charge level of the battery, expressed as a percentage.
  • Status of Health (SOH): The overall health and capacity of the battery, expressed as a percentage, often accompanied by a status like 'GOOD', 'REPLACE', or 'RECHARGE'.
Image showing FBT200 test results display examples

Figure 5: Example Test Results Display

4.4. Supported Test Functions

The FBT200 can perform the following tests:

  • Status of Charge Test
  • Status of Health Test
  • Voltage Test
  • CCA Test
  • Resistance Test
FBT200 Smart Battery Tester features overview

Figure 6: FBT200 Key Test Functions

5. Maintenance

  • Keep the device clean and dry. Wipe the casing with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • After each use, clean any residue from the battery clamps to ensure good conductivity for future tests.
  • Store the FBT200 in its provided pouch in a cool, dry place away from direct sunlight and extreme temperatures.
  • Do not attempt to open the device casing, as this will void any potential warranty.

6. Troubleshooting

  • Device does not power on: Ensure the clamps are securely connected to the correct battery terminals (red to positive, black to negative). Check if the battery has sufficient voltage (above 8V) for the tester to power on.
  • Inaccurate readings: Verify that battery terminals are clean and free of corrosion. Ensure clamps have a firm, direct contact with the battery posts.
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.