1. Introduction
Thank you for purchasing the CA30 car audio power amplifier.
The CA30 is a high-performance car amplifier manufactured by Fosi Audio, designed for 12V automotive systems to deliver HiFi sound reproduction and amplification. With latest Infineon's automotive-grade Class D amplifier chips, it features a compact heatsink design (186x101x44.2mm), high power output (4x100W@4Ω/4x160W@2Ω), High fidelity (full-range & flat frequency response 10Hz~40KHz), exceptional efficiency (over 88%). It is specifically engineered for audiophiles seeking premium sound quality in automotive entertainment systems.
The CA30 features high-pass/low-pass/full-pass filters, enabling flexible configuration as a high-frequency, low-frequency, or full-range speaker system. Its crossover frequencies can be precisely adjusted according to users' preferences. It also supports RCA low-level/high-level inputs (High input with sensing DC offset and auto turn-on function), compatible with most original car head unit systems equipped with RCA line outputs or high-level outputs. Whether you're a car audio enthusiast or audiophile, the CA30 will take you on an extraordinary journey of HiFi music.
Thank you again for your support. Fosi Audio is committed to delivering premium in-vehicle audio solutions, ensuring every user enjoys exceptional sound quality.
Video: Fosi Audio CA30 Car Amplifier Product Showcase.
2. Safety Information
Please read all instructions carefully before installation and use. Keep this manual for future reference.
- Power Supply: This amplifier is designed for 12V automotive systems. Do not connect to other voltage sources.
- Wiring: Ensure all wiring is correctly connected and securely fastened to prevent short circuits or damage. Use appropriate gauge wires as specified.
- Fusing: Always use the correct fuse rating (30A x 2 internal) and install an external fuse on the +12V power line within 12-16 inches of the battery.
- Heat: The amplifier generates heat during operation. Ensure adequate ventilation and do not mount it in enclosed spaces without airflow.
- Professional Installation: If you are unsure about any aspect of installation, seek assistance from a qualified car audio professional.
- Avoid Moisture: Do not expose the amplifier to moisture or water.
3. Product Overview
The Fosi Audio CA30 is a compact 4-channel Class D amplifier designed for high-fidelity car audio.

Image: Fosi Audio CA30 Car Amplifier main product view.
Panel Overview

Image: Detailed panel overview of the Fosi Audio CA30 amplifier, showing controls and input/output ports.
- Crossover Frequency Control (FREQ): Adjusts the crossover frequency for the rear channels (CH3/4) when HPF or LPF is selected. Range: 50Hz to 250Hz.
- Crossover Mode Select Switch (X-OVER): Selects the crossover mode:
- FULL: Full range output.
- HPF (High Pass Filter): Limits low-frequency information to speakers.
- LPF (Low Pass Filter): Limits high-frequency information to speakers.
- Gain Control (GAIN): Matches the input signal level from your source unit to the amplifier.
- Power/Protection/Clipping Indicators (PWR/PRT/CLIP):
- PWR (Blue): Lights up when the amplifier is on.
- PRT (Red): Indicates protection mode (critical operation).
- CLIP (Yellow): Indicates acoustic output distortion; adjust gain settings.
- Line Input (RCA): RCA jacks for low-level signal input (CH1/2 or CH1/2/3/4). Connect to source unit using RCA cables, keeping them away from power wiring.
- High Level Input: For connection to speaker outputs of your source unit (head unit) if it lacks low-level RCA outputs.
- Power Terminals: Connects DC power (GND, REM, +12V) to the amplifier.
- Speaker Terminals: Connects speaker cables to the amplifier.
4. Package Contents
Please check the box for the following items:

Image: Contents of the Fosi Audio CA30 amplifier box.
- Fosi Audio CA30 Amplifier x1
- 8-Pin Ribbon Cable x1
- Wrenches x2
- Screws (not pictured in manual, but typically included)
- 30A Fuse x2 (not pictured in manual, but typically included)
- User Manual x1 (PDF version available at official link)
5. Setup
5.1 Power Connections
Proper power connections are crucial for amplifier performance and safety.

Image: Wiring diagram for power connections to the Fosi Audio CA30 amplifier.
- +12V Battery Connection: Connect a power wire (min. AWG 10) to the vehicle's positive battery terminal. This connection must be tight and secure. Install an appropriate fuse (matching amplifier's fuse rating) within 12-16 inches of the battery. Connect the power wire to the +12V terminal of the amplifier. Do not install the fuse until all connections are complete.
- Ground Connection (GND): Connect a ground wire (min. AWG 10) to the vehicle's chassis. Keep the wire as short as possible. Ensure a solid metal-to-metal connection by sanding off any paint, rust, or grime at the contact point. Connect the ground wire to the GND terminal of the amplifier.
- Remote Turn-On (REM): The REM control line turns the amplifier on/off with your source unit. Connect a 12-16 gauge wire from your source unit's remote turn-on output (or ignition switch circuit) to the REM terminal of the amplifier. If using high-level input with DC offset sensing for auto turn-on, you may not need to connect the REM line.
5.2 Input Connections
RCA Low Level Connection
Use RCA cables to connect your source unit's low-level outputs to the amplifier's RCA Line Inputs.

Image: Wiring diagram for RCA low-level input connections to the Fosi Audio CA30 amplifier.
High Level Input
If your source unit (head unit) does not have RCA low-level outputs, you can connect its speaker outputs directly to the amplifier's High Level Input using the provided 8-pin ribbon cable. The amplifier features DC offset sensing for auto turn-on when using high-level inputs.
5.3 Speaker/Subwoofer Wiring
Connect your speakers or subwoofers to the amplifier's speaker terminals. Ensure correct polarity (+ to + and - to -).

Image: Wiring diagrams for connecting speakers and subwoofers to the Fosi Audio CA30 amplifier.
- 4-Channel Speaker Configuration: Connect each speaker to its respective channel (CH1, CH2, CH3, CH4). Minimum impedance for each channel is 2Ω.
- Bridged Subwoofer Configuration: For higher power output to a subwoofer, channels can be bridged. For example, bridge CH1 and CH2 for one subwoofer, and CH3 and CH4 for another. Refer to the diagram for specific bridging connections. Minimum impedance for bridged channels is 4Ω.
5.4 Crossover and Gain Settings
- X-OVER Switch: Select FULL for full-range speakers, HPF for tweeters/mid-range speakers (to filter out bass), or LPF for subwoofers (to filter out high frequencies).
- FREQ Control: If HPF or LPF is selected, adjust the FREQ knob to set the desired crossover point between 50Hz and 250Hz.
- GAIN Control: Start with the GAIN knob at minimum. Turn on your audio system and gradually increase the volume of your source unit until it's near maximum (about 75-80%). Then, slowly increase the amplifier's GAIN until you hear distortion, then back off slightly. This ensures optimal signal-to-noise ratio and prevents clipping.
6. Operating
Once all connections are made and settings are configured, turn on your vehicle's ignition and source unit. The amplifier's blue PWR indicator should light up, indicating it is powered on.
- PWR (Blue): Indicates the amplifier is receiving power and is operational.
- PRT (Red): If this light illuminates, the amplifier has entered protection mode due to an issue (e.g., short circuit, overheating, low voltage). Turn off the system, check all connections and wiring, and allow the amplifier to cool down if overheating is suspected.
- CLIP (Yellow): If this light illuminates, the audio signal is clipping (distorting). Reduce the GAIN setting on the amplifier or the volume from your source unit until the CLIP light turns off.
7. Maintenance
- Cleaning: Use a soft, dry cloth to clean the amplifier's exterior. Do not use harsh chemicals or solvents.
- Connections: Periodically check all power, ground, input, and speaker connections to ensure they are secure and free from corrosion.
- Ventilation: Ensure the amplifier's heatsink fins are free from dust and debris to maintain proper cooling.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No Power (PWR light off) | Blown fuse, loose power/ground/REM connection, no 12V supply. | Check external and internal fuses. Verify +12V, GND, and REM connections. Ensure battery has power. |
| No Sound | Loose input/speaker connections, incorrect input source, amplifier in protection mode. | Check RCA/high-level input and speaker wiring. Ensure source unit is playing. If PRT light is on, troubleshoot protection mode. |
| Distorted Sound (CLIP light on) | Gain set too high, poor quality input signal, speaker impedance mismatch. | Reduce GAIN. Check source unit output. Verify speaker impedance matches amplifier's rating. |
| Amplifier Overheats (PRT light on) | Insufficient ventilation, impedance too low, prolonged high output. | Ensure proper airflow around amplifier. Check speaker impedance. Reduce volume or allow cooling. |
| Noise/Hum | Poor grounding, RCA cables near power wires, ground loop. | Verify ground connection. Reroute RCA cables away from power wires. Install a ground loop isolator if necessary. |
9. Specifications
| Parameter | Value |
|---|---|
| Rated Power Output (Tested Voltage 14.4Volts) | CA30 |
| RMS Power @ 4 ohm | 100Wx4 |
| RMS Power @ 2 ohm | 160Wx4 |
| Bridge Power @ 4 ohm | 320Wx2 |
| Frequency response | 10Hz-40KHz |
| Low Pass Frequency Crossover | 50Hz-250Hz |
| High Pass Frequency Crossover | 50Hz-250Hz |
| Power/Protection Indicator | Blue / Red |
| Clipping indicator light | Orange |
| Damping coefficient (100Hz @ 10W) | ≥140 |
| Input Sensitivity | 0.75-8V |
| Interference@1kHz | ≥60dB |
| Signal Noise Ratio | >100dB |
| SINAD | ≥80dB |
| Remaining noise | ≤200μV |
| T.H.D +@5W | ≤ 0.008% |
| Fuse | 30A x 2 (Internal) |
| Dimension (mm) (LxWxH) (Inches) | 186x101x44.2 (7.3x3.9x1.7) |
10. User Tips
- Compact Powerhouse: Despite its small size, the CA30 is quite heavy, indicating robust build quality, especially in its connection terminals.
- Clean Sound: Users report clean sound with no noticeable noise at both low and high volumes, making it suitable for critical listening.
- Gain Adjustment: While the amplifier sounds clean, some users noted a bit of noise when using maximum gain. It's recommended to set the gain carefully to avoid this.
- Heat Management: The unit can get warm quickly during operation, but typically not excessively hot. Ensure it has adequate ventilation.
- Versatile Setup: The controls allow for precise tuning to match various speaker and subwoofer setups, providing a great stereo effect and solid bass.
11. Warranty and Support
Fosi Audio pledges to give a 12-month limited warranty and support from the date of purchase. If you encounter any problem when using your product, please contact our support team.
After-Sales Service and Technical Support Email: support@fosiaudio.com
Official Website: www.fosiaudio.com