RACBOX 81536 52C80 60C30

Contents

RACBOX Tail Light LED Modules Unit Brake Taillight User Manual

Model: 81536 52C80 60C30

1. Introduction

This manual provides essential information for the safe and effective installation and operation of your RACBOX Tail Light LED Modules Unit Brake Taillight. This product is an auxiliary accessory designed for automotive lighting, intended for normal replacement and upgrade of original car lights. It is not for illegal modification or use.

Compatibility: Toyota Camry C-HR (2018, 2019, 2020, 2021) and Land Cruiser Prado (2022).

RACBOX LED Tail Light Modules and their illuminated output.
Figure 1: RACBOX LED Tail Light Modules and their illuminated output.

2. Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

3. Installation Instructions

Follow these steps carefully to install the new tail light assembly:

  1. Turn off the vehicle engine and disconnect the power supply to avoid short circuit.
  2. Locate the mounting position of the original tail light.
  3. Remove the fixing screws or clips that hold the stock light assembly.
  4. Unplug the power connector and take off the original tail light.
  5. Install the new tail light assembly into the mounting position.
  6. Secure the light assembly with screws or clips to ensure stable installation.
  7. Connect the power plug correctly. If the light does not work, reverse the plug polarity.
  8. Test all light functions to ensure normal operation.
  9. Recheck all screws and connections to make sure they are firm and reliable.
Close-up of the 3-pin connector on the LED module.
Figure 2: Detail of the 3-pin connector for proper connection.
RACBOX LED modules installed in a vehicle's taillight, demonstrating the red light output.
Figure 3: Example of installed LED modules in a vehicle's taillight.

4. Operating Instructions

Once correctly installed and connected, the LED modules will function as brake taillights, illuminating when the vehicle's brake pedal is pressed. Ensure all light functions are tested after installation for proper operation.

Comparison of single and dual LED illumination intensity.
Figure 4: Visual comparison of LED illumination intensity.

5. Maintenance

These LED modules are designed for durability and require minimal maintenance. Periodically inspect the lights for any signs of damage or loose connections. Clean the lens covers with a soft, damp cloth if they become dirty to ensure maximum light output.

6. Troubleshooting

Light Does Not Work After Installation

  • Ensure the vehicle's power supply is connected.
  • If the light does not illuminate, disconnect the power plug, reverse its polarity, and reconnect.
  • Check all connections to ensure they are firm and secure.
  • Verify that the module itself is not damaged.

7. Specifications

Attribute Value
Item Type Tail Light Assembly
Voltage 12 V
Origin Mainland China
High-concerned chemical None
Module Dimensions (approx.) 36mm (Length) x 32mm (Diameter)
Package Weight (approx.) 0.16 kg
Package Dimensions (approx.) 8cm (Length) x 6cm (Width) x 3cm (Height)
Detailed view of a single LED module with dimensions: 36mm length, 32mm diameter.
Figure 5: LED module with approximate dimensions.

8. User Tips

  • The 3-pin connector is a direct replacement, often requiring no modifications.

9. Warranty & Support

For any support or warranty inquiries, please contact the manufacturer:

Manufacturer: Guangzhou Bai Ji Tun Trading Co., Ltd, C116, No.1489, Fanghua Road Baiyun Guangzhou.

EU Authorized Representative: APEX CE SPECIALISTS LIMITED, UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND.

A detailed user manual in PDF format is available for download. Reference: User manual (PDF)

10. Compliance Information

This product is an auxiliary accessory for automotive lighting and is only used for the normal replacement and upgrade of the original car lights, not for illegal modification or illegal use. The products meet the relevant national automotive lighting industry standards, and have undergone strict quality testing before leaving the factory, and are qualified to leave the factory.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.