Creality 3D Hyper PETG series

Contents

Creality Hyper PETG Filament User Manual

High-Speed 3D Printer Filament

1. Introduction

The Creality Hyper PETG Filament is engineered for high-speed 3D printing, offering excellent performance for a wide range of applications. This filament combines the strength and durability of PETG with optimized properties for faster extrusion and layer adhesion, making it ideal for modern high-speed 3D printers like the Creality K1 Max. It provides a balance of flexibility, strength, and temperature resistance, along with a smooth finish.

Creality Hyper PETG Filament spools in various colors
Figure 1: Creality Hyper PETG Filament is available in a variety of vibrant colors.

Key features include:

  • High-Speed Printing: Designed to perform optimally at speeds from 30mm/s up to 600mm/s.
  • High Accuracy: Manufactured with a diameter tolerance of ±0.03 mm for consistent extrusion.
  • Robust and Resilient: Offers good mechanical strength, impact resistance, and durability.
  • Effortless Extrusion: Formulated for smooth feeding and reduced clogging.
  • Waterproof and Sun-resistant: Suitable for functional parts exposed to environmental elements.
  • Translucent and Colorful: Provides options for visually appealing prints with varying degrees of translucency depending on color.
3D printed green boat model with 'Fast Printing Speed 600mm/s' text overlay
Figure 2: The Hyper PETG filament supports fast printing speeds up to 600mm/s, demonstrated by a quickly printed boat model.

2. Setup and Loading

Proper filament loading is crucial for successful 3D printing. Follow these general steps:

  1. Unpack the Filament: Carefully remove the spool from its vacuum-sealed packaging. Keep the desiccant packet for storage.
  2. Prepare Your Printer: Ensure your 3D printer is turned on and the print head is at room temperature or preheated to a low temperature (e.g., 180°C) to soften any residual filament in the nozzle.
  3. Mount the Spool: Place the filament spool onto your printer's spool holder, ensuring it can unroll smoothly without snagging.
  4. Feed the Filament: Gently guide the end of the filament into the extruder's intake hole. For direct drive extruders, push it directly towards the hotend. For Bowden systems, feed it through the PTFE tube until it reaches the hotend.
  5. Extrude Manually: Once the filament is in place, use your printer's interface to manually extrude a small amount of filament. You should see a steady, clean stream of PETG coming out of the nozzle. If not, ensure the nozzle is clear and the filament is properly seated.
  6. Trim the End: Always cut the end of the filament at a 45-degree angle before loading to ensure a smooth entry into the extruder.

3. Operating Parameters

Optimal printing parameters can vary slightly between printers and specific models. The following are general recommendations for Creality Hyper PETG Filament:

ParameterRecommended Range
Nozzle Temperature230°C - 250°C
Bed Temperature70°C - 80°C
Printing Speed30mm/s - 600mm/s (adjust based on printer capability)
Cooling Fan20% - 50% (start lower to improve layer adhesion, increase for overhangs)
Retraction Distance1mm - 5mm (direct drive vs. Bowden, adjust to reduce stringing)
Retraction Speed30mm/s - 60mm/s
First Layer Speed10mm/s - 20mm/s (for optimal bed adhesion)

Tips for PETG Printing:

  • Bed Adhesion: PETG adheres well to PEI sheets, glass with glue stick, or blue painter's tape. Ensure your bed is clean and level.
  • Stringing: PETG is prone to stringing. Fine-tune retraction settings (distance and speed) and potentially lower print temperature slightly if stringing persists.
  • First Layer: A slightly higher first layer height and slower speed can improve bed adhesion significantly.
  • Cooling: Too much cooling can reduce layer adhesion and make prints brittle. Start with lower fan speeds and increase only if necessary for overhangs or bridging.
Grid of six images showing 3D printed translucent lamps in different colors
Figure 3: Hyper PETG filament can produce translucent and colorful prints, ideal for decorative items like lamps.

4. Maintenance and Storage

Proper maintenance and storage of your filament will ensure consistent print quality and extend its shelf life.

  • Keep Dry: PETG is hygroscopic, meaning it absorbs moisture from the air. Store unused filament in a dry, airtight container or bag with desiccant packets (silica gel).
  • Drying Filament: If your filament has absorbed moisture (indicated by popping sounds during printing, stringing, or poor layer adhesion), it can be dried. A common method is to place it in a filament dryer or a convection oven at 60°C for 4-6 hours.
  • Avoid Tangling: Always secure the end of the filament to the spool when not in use to prevent tangling, which can lead to print failures.
  • Handle with Care: Avoid dropping spools, as this can damage the filament or the spool itself.

5. Troubleshooting Common Issues

Here are some common issues encountered with PETG and potential solutions:

  • Stringing/Oozing:
    • Cause: Incorrect retraction settings, too high print temperature, or wet filament.
    • Solution: Adjust retraction distance and speed, lower print temperature in 5°C increments, or dry the filament.
  • Poor Bed Adhesion:
    • Cause: Unlevel bed, dirty print surface, incorrect bed temperature, or too fast first layer speed.
    • Solution: Level the print bed, clean the print surface thoroughly, increase bed temperature, or decrease first layer speed. Use an adhesive aid if necessary.
  • Layer Separation/Weak Layers:
    • Cause: Too low print temperature, excessive cooling, or wet filament.
    • Solution: Increase nozzle temperature, reduce cooling fan speed, or dry the filament.
  • Clogging:
    • Cause: Dust on filament, heat creep, or incorrect retraction settings.
    • Solution: Ensure filament is clean, check hotend cooling, adjust retraction settings.

6. Specifications

PropertyValue
MaterialPETG (Polyethylene Terephthalate Glycol)
Filament Diameter1.75 mm
Diameter Accuracy± 0.03 mm
Net Weight1 kg / Spool
Recommended Printing Speed30 - 600 mm/s
Model NumberHyper PETG series
FormSolid
Shelf Life1 year
Package Length21 cm
Package Width21 cm
Package Height7 cm
Package Weight1.35 kg
Brand NameCREALITY 3D
OriginMainland China
Hand wearing a 3D printed black and white wrist brace, labeled 'Robust Upgrade, Sturdy and Resilient'
Figure 4: Hyper PETG filament produces robust and resilient parts, suitable for functional applications like this wrist brace.

7. User Tips

  • Calibrate E-steps: Ensure your extruder's E-steps are accurately calibrated for precise filament extrusion, especially when switching filament types.
  • Flow Rate Adjustment: Perform a flow rate calibration for PETG to ensure dimensional accuracy and prevent over/under-extrusion.
  • Z-Offset: A slightly higher Z-offset for the first layer compared to PLA can sometimes help prevent PETG from sticking too aggressively to the build plate, making removal easier.
  • Experiment: Don't be afraid to experiment with small temperature or speed adjustments to find the sweet spot for your specific printer and desired print quality.
  • Post-Processing: PETG can be sanded, painted, and glued. For best results, use appropriate tools and adhesives.
3D printer extruding yellow filament to create a rocket nose cone, labeled 'Effortless Extrusion'
Figure 5: The filament is designed for effortless extrusion, ensuring smooth printing of complex shapes.

8. Frequently Asked Questions (FAQ)

Q: What is PETG filament?
A: PETG (Polyethylene Terephthalate Glycol) is a thermoplastic polyester that combines the ease of use of PLA with the strength and durability of ABS. It offers good impact resistance, chemical resistance, and is often used for functional parts.
Q: Is Hyper PETG compatible with all 3D printers?
A: Creality Hyper PETG filament is designed for FDM (Fused Deposition Modeling) 3D printers that can reach the required printing temperatures (230-250°C nozzle, 70-80°C bed). It is optimized for high-speed printers but works well with standard speed printers too.
Q: How do I prevent stringing with PETG?
A: Stringing is common with PETG. To reduce it, fine-tune your retraction settings (distance and speed), ensure your filament is dry, and consider slightly lowering your print temperature.
Q: Can I use PETG for outdoor applications?
A: Yes, PETG has good UV resistance and is less prone to warping than some other filaments, making it suitable for many outdoor applications. The Hyper PETG is specifically noted as waterproof and sun-resistant.
3D printed white plant pot with a plant, hanging by twine, labeled 'Waterproof and Sun-resistant'
Figure 6: The waterproof and sun-resistant properties of Hyper PETG make it suitable for outdoor items like this plant pot.

9. Warranty and Support

For detailed product information, troubleshooting guides, and support, please refer to the official Creality resources. A comprehensive user manual in PDF format may be available for download from the manufacturer's website or via the following link: Creality Hyper PETG Filament User Manual (PDF).

For further assistance, please contact Creality 3D Creative Store support channels.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.