Peugeot Car HD Projector Lamp

Contents

Peugeot Car HD Projector Lamp LED Auto Door Welcome Light User Manual

1. Product Overview

The Car HD Projector Lamp LED Auto Door Welcome Light is designed to project a clear Peugeot logo onto the ground when the car door is opened. This enhances the aesthetic appeal of your vehicle and provides additional illumination when entering or exiting the car. It is a high-efficiency, energy-saving accessory with easy, non-destructive installation.

Overhead view of a car with all doors open, showing projected Peugeot logos on the ground.
Figure 1.1: Car with projected Peugeot logos from open doors.

2. Safety Information & Warnings

  • Prohibited from use if damaged or aged. Ensure the product is in good condition before installation and use.
  • Do not operate with wet hands. This can lead to electrical hazards.
  • Prohibition of modification. Do not attempt to alter or modify the device. Standardized operation is required.
  • Use in appropriate scenarios. Do not misuse the product or use it for purposes other than its intended function.
  • Keep out of reach of children. Ensure proper use and operation, and do not allow children to come into contact with the device.
  • Strictly follow all requirements for use.

3. Package Contents

Please check the package contents upon receipt. The standard package includes:

  • Car HD Projector Lamp LED Auto Door Welcome Light unit(s)
  • Adhesive pads for installation
  • Note: AAA batteries are NOT included and must be purchased separately.

4. Installation Guide

This product features an easy, non-destructive installation process, requiring no drilling or changes to the original vehicle wiring.

4.1. Battery Installation

  1. Locate the battery compartment on the projector lamp.
  2. Open the battery cover.
  3. Insert three (3) AAA batteries, ensuring correct polarity (+/-).
  4. Close the battery cover securely.
Projector with battery compartment open, showing AAA batteries being inserted.
Figure 4.1: Battery installation in the projector unit.

4.2. Device Placement and Adhesion

  1. Clean the desired installation area on the car door panel thoroughly. Ensure it is dry and free of dust or grease.
  2. Peel off the protective film from the adhesive pad on the back of the projector lamp.
  3. Firmly stick the light onto the car door panel. Ensure the sensor on the projector is facing downwards or towards the car's threshold for proper operation.
  4. Press firmly for a few seconds to ensure good adhesion.
  5. Install firmly and conduct regular inspections to ensure the device remains securely attached.
Hands applying the adhesive to the back of the projector unit.
Figure 4.2: Applying the adhesive pad to the projector.
Projector unit installed on the car door panel.
Figure 4.3: Projector installed on the car door.

5. Operating Instructions

The Car HD Projector Lamp is designed for automatic operation:

  • When you open the car door, the car logo light will automatically display on the ground.
  • When you close the car door, the light will automatically turn off.
  • The projector uses an AC lens with high permeability to ensure a clear and bright projection.
Comparison image showing a car door area before and after the welcome light projects a Peugeot logo.
Figure 5.1: Before and after projection.
A clear Peugeot logo projected onto the ground from an open car door.
Figure 5.2: Projected logo from an open door.

6. Maintenance

  • Cleaning: Wipe the device with a soft, dry cloth. Do not use strong acidic or alkaline cleaning agents, as these can damage the product's finish or internal components.
  • Storage: If storing the device for an extended period, ensure it is kept in a moisture-proof and anti-extrusion environment. Remove batteries if not in use for a long time to prevent leakage.
  • Protection: Avoid severe impact and exposure to high temperatures, which can affect the device's performance and lifespan.
  • Inspections: Periodically check the adhesion of the device to the car door to ensure it remains securely in place.

7. Troubleshooting

  • Light not projecting:
    • Check if the batteries are installed correctly with the right polarity.
    • Replace old batteries with new AAA batteries.
    • Ensure the car door is fully open for the sensor to activate.
    • Verify that the sensor is not obstructed or dirty.
  • Projected image is dim or unclear:
    • Replace batteries with fresh ones.
    • Clean the projector lens with a soft, dry cloth.
  • Device falling off the door:
    • Ensure the installation surface was clean and dry before adhesion.
    • Re-apply with new, strong double-sided adhesive tape.
  • Quality issues or empty package: If you encounter any quality issues with the product or receive an empty package, please contact customer service for assistance and verification.

8. Specifications

Feature Detail
Product Type Car Welcome Light / HD Projector Lamp
Material ABS
Dimensions (L x W) 6.6 cm x 6.4 cm
Estimated Package Dimensions (L x W x H) 5 cm x 5 cm x 5 cm
Power Supply 3 x AAA Batteries (not included)
LED Color Temperature 6000 K
Product Color Black
Product Weight 0.141 kg
Diagram showing the dimensions of the projector unit as 6.6cm by 6.4cm.
Figure 8.1: Product dimensions.

9. User Tips

  • For optimal projection clarity, ensure the installation surface is flat and the projector is positioned to avoid shadows from the car's body.
  • Consider using high-quality alkaline AAA batteries for longer-lasting performance.
  • If installing on multiple doors, ensure consistent placement for a uniform look.

10. Warranty and Support

If there are quality issues with the product, it can be returned. For specific return procedures or further support, please contact customer service.

For more detailed information and comprehensive instructions, you may refer to the official user manual PDF available at: Official User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.