1. Introduction
This manual provides essential information for the safe and correct installation, maintenance, and use of your new rear tail light gaskets for the Peugeot 307 Hatchback. Please read all instructions carefully before proceeding with installation.
2. Safety & Warnings
- WARNING: Improper installation can lead to water ingress, electrical issues, or damage to the vehicle's tail light assembly.
- Installation should ideally be performed by qualified technicians or individuals with appropriate automotive repair experience.
- Always ensure the vehicle is stable and the engine is off before beginning any work.
- Wear appropriate personal protective equipment, such as gloves and eye protection, during installation.
- Do not use damaged, expired, or inferior quality accessories.
- Modification or disassembly of the gaskets is prohibited.
3. Setup (Installation)
3.1. Product Application Scope
This product is a specific replacement gasket for the rear tail lights of Peugeot 307 Hatchback models manufactured between 2004 and 2013. Ensure your vehicle matches this specification.
3.2. Pre-Installation Checks
- Before installation, turn off the vehicle's engine, disconnect the battery (if working with electrical components), and ensure the vehicle is stable and cool.
- Verify that the new gaskets are intact, free of damage, deformation, cracks, or missing parts.
- Confirm that the shape and size of the new gaskets match the original gaskets being replaced.
3.3. Installation Procedure
- Carefully remove the existing tail light assembly from your Peugeot 307 Hatchback according to your vehicle's service manual.
- Remove the old, worn, or damaged gasket from the tail light assembly or vehicle body.
- Thoroughly clean the mounting surface on both the tail light assembly and the vehicle body. Ensure it is free of old gasket material, dirt, dust, grease, and moisture. A clean, dry surface is crucial for proper sealing.
- Identify the left (Part M039-1) and right (Part M039-4) gaskets.
- Peel off the protective backing from the adhesive side of the new gasket.
- Carefully align the new gasket with the tail light assembly or the vehicle body (depending on where the original gasket was seated) and press firmly to ensure good adhesion and a complete seal.
- Reinstall the tail light assembly back into your vehicle, ensuring all mounting points are securely fastened.

Figure 1: Front view of the left and right tail light gaskets.

Figure 2: Rear view of the left and right tail light gaskets, showing the adhesive backing.

Figure 3: Front view of the left tail light gasket (Part M039-1).

Figure 4: Front view of the right tail light gasket (Part M039-4).
3.4. Post-Installation Checks
- Ensure the tail light assembly is firmly secured and does not wobble.
- Check for any gaps between the tail light assembly and the vehicle body that could indicate an improper seal.
- Test all tail light functions (brake lights, turn signals, running lights, reverse lights) to ensure they operate correctly.
4. Operating
As a static sealing component, the tail light gasket does not have operational functions. Its purpose is to provide a watertight seal for the tail light assembly.
5. Maintenance
- Regularly inspect the area around the tail lights for any signs of water ingress or condensation inside the light housing, which could indicate a compromised seal.
- Keep the exterior of the tail light assembly clean to prevent dirt and debris from accumulating around the gasket edges.
- Avoid using harsh chemicals or abrasive cleaners on or near the gasket, as this may degrade the material.
6. Troubleshooting
- Water or Condensation Inside Tail Light: If you observe moisture inside the tail light housing after installation, it indicates a leak. Re-check the gasket's seating, ensure the mounting surface was clean and dry, and that the tail light assembly is properly secured. If the issue persists, the gasket may need to be re-seated or replaced.
- If any accessory appears abnormal or fails to provide an effective seal, it must be stopped immediately and replaced or repaired.
7. Specifications
| Product Name | Rear Tail Light Gasket |
| Item Type | Automotive Sealing Component |
| Compatibility | Peugeot 307 Hatchback (2004-2013) |
| Part Numbers | Left: M039-1, Right: M039-4 |
| Package Contents | 1 Pair (1 Left Gasket, 1 Right Gasket) |
| Package Dimensions (Approx.) | Length: 18 cm, Width: 15 cm, Height: 10 cm |
| Package Weight (Approx.) | 0.2 kg |
8. User Tips
- Before applying the new gasket, ensure the mating surfaces on both the vehicle and the tail light assembly are perfectly clean and dry. Any residue can compromise the seal.
- When pressing the gasket into place, apply even pressure across its entire surface to ensure maximum contact with the adhesive.
9. Warranty & Support
For any questions regarding installation, product defects, or warranty claims, please contact your seller directly. Keep your purchase receipt as proof of purchase.
Manufacturer Information:
Company Name: Zhengzhou Tangner Trading Co., Ltd.
Address: Room 2, Building 3, No. 69 Hejiang Road, Erqi District, Zhengzhou City Yuan 15th floor east door
Email: yangnanxiang@163.com
Telephone: +86-18637168189
EU Authorized Representative:
Company Name: eVatmaster Consulting GmbH
Address: Bettinastr. 30, 60325
Email: contact@evatmaster.com
Telephone: +49-6995179070