PowMr POW-LVM4K-24V

Contents

PowMr 4KW 120V Off-Grid Solar Inverter Charger

Model: POW-LVM4K-24V

User Manual

1. About This Manual

This manual describes the assembly, installation, operation, and troubleshooting of the PowMr 4KW 120V Off-Grid Solar Inverter Charger. Please read this manual carefully before installation and operation, and keep it for future reference.

1.1. Purpose

This manual provides detailed instructions for the proper use and maintenance of your inverter charger.

1.2. Scope

This manual covers safety guidelines, installation procedures, and information regarding tools and wiring for the inverter charger.

2. Safety Instructions

WARNING: This chapter contains important safety and operating instructions. Read and keep this manual for future reference.

  1. Before using the unit, read all instructions and cautionary markings on the unit, the batteries, and all appropriate sections of this manual.
  2. CAUTION: To reduce the risk of injury, charge only deep-cycle lead-acid type rechargeable batteries. Other types of batteries may burst, causing personal injury and damage.
  3. Do not disassemble the unit. Take it to a qualified service center when service or repair is required. Incorrect re-assembly may result in a risk of electric shock or fire.
  4. To reduce the risk of electric shock, disconnect all wirings before attempting any maintenance or cleaning. Turning off the unit will not reduce this risk.
  5. CAUTION: Only qualified personnel can install this device with a battery.
  6. NEVER charge a frozen battery.
  7. For optimum operation of this inverter/charger, please follow the required specifications to select appropriate cable sizes. It is very important to correctly operate this inverter/charger.
  8. Be very cautious when working with metal tools on or around batteries. A potential risk exists to drop a tool to spark or short circuit batteries or other electrical parts and could cause an explosion.
  9. Please strictly follow the installation procedure when you want to disconnect AC or DC terminals. Refer to the INSTALLATION section of this manual for details.
  10. GROUNDING INSTRUCTIONS: This inverter/charger should be connected to a permanent grounded wiring system. Be sure to comply with local requirements and regulations to install this inverter.
  11. NEVER cause AC output and DC input short circuits. Do NOT connect to the mains when DC input short circuits.
  12. Warning!! Only qualified service persons are able to service this device. If errors still persist after following the troubleshooting table, please send this inverter/charger back to a local dealer or service center for maintenance.

3. Introduction

The PowMr 4KW 120V Off-Grid Solar Inverter Charger is a multi-function inverter/charger, combining the functions of an inverter, MPPT solar charger, and battery charger to offer uninterruptible power support in a portable size. Its comprehensive large LCD display offers user-configurable and easy-accessible touch button operation for settings such as battery charging current, AC/solar charger priority, and acceptable input voltage based on different applications.

3.1. Features

  • Off-grid solar inverter
  • No battery function available
  • Under Battery Mode, AC voltage can be adjusted to 100VAC, 110VAC, and 120VAC.
  • Utility power, battery, and PV power complement each other
  • Pure sine wave solar inverter
  • Unique glass top cover design with 6.25-inch LCD display and touchable buttons
  • Built-in 150A MPPT (Max PV 7200W) solar charger
  • High PV input range from 55V-450Vdc
  • Smart battery charger design for optimized battery performance
  • Configurable AC/Battery input priority via LCD setting
  • Auto restart while PV is recovering
  • Over-load, over temperature, and output short circuit protection
  • Cold restart function
  • Built-in lithium battery automatic activation
  • Communication with RS232/RS485
  • WiFi monitoring function (optional)
  • Anti-dust kit for harsh environments (optional)
  • Restore default settings with one click

3.2. Basic System Architecture

The following illustration shows the basic application for this inverter/charger. It includes connections to a generator or utility, and optional PV modules. This inverter can power various home or office appliances, including motor-type appliances like tube lights, fans, refrigerators, and air conditioners.

Hybrid Power System Diagram
Figure 1: Hybrid Power System. This diagram illustrates how the solar inverter connects solar power, a generator or utility, and external battery packs to power home appliances.

4. Installation

4.1. Unpacking and Inspection

Before installation, please inspect the unit. Ensure that nothing inside the package is damaged. The package should contain the unit (x1) and the user manual (x1).

4.2. Preparation

Before connecting all wirings, remove the bottom cover by unscrewing two screws.

4.3. Mounting the Unit

Consider the following points when selecting where to install the unit:

  • Do not mount the inverter on flammable construction materials.
  • Mount on a solid surface.
  • Install this inverter at eye level for easy LCD display readability.
  • The ambient temperature should be between 0°C and 55°C for optimal operation.
  • The recommended installation position is vertically on the wall.
  • Ensure sufficient heat dissipation and space for wiring by maintaining clearances as shown in the diagram.

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE ONLY.

Mounting the Unit Diagram
Diagram showing recommended vertical wall mounting with specified clearance distances (20cm sides, 50cm top/bottom) for optimal heat dissipation and wiring access.

Install the unit by screwing two screws after mounting.

4.4. Battery Connection

CAUTION: For safety operation and regulation compliance, it's requested to install a separate DC over-current protector or disconnect device between battery and inverter. It may not be requested to have a disconnect device in some applications, however, it's still requested to have over-current protection installed. Please refer to the typical amperage in the table below for required fuse or breaker size.

WARNING! All wiring must be performed by qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for battery connection. To reduce risk of injury, please use the proper recommended cable and terminal size as below.

Ring Terminal Diagram
Diagram showing the structure of a ring terminal for battery connection, with dimensions D, L, and M.
Recommended Battery Cable and Terminal Size
ModelTypical AmperageBattery CapacityWire SizeCable mm²Ring Terminal Dimensions (D mm)Ring Terminal Dimensions (L mm)Ring Terminal Dimensions (M mm)Torque Value
3.0KW 24V110A100AH/200AH1*4AWG2284418.22~3 Nm
4.0KW 24V150A200AH1*2AWG3584418.22~3 Nm

Follow these steps to connect the battery:

  1. Assemble the battery ring terminal based on the recommended battery cable and terminal size.
  2. Connect all battery packs as required by the unit.
  3. NOTE: Please only use sealed lead-acid battery or sealed GEL/AGM lead-acid battery or lithium battery.
  4. Insert the ring terminal of the battery cable flatly into the battery connector of the inverter and ensure the bolts are tightened with a torque of 2-3 Nm. Ensure polarity at both the battery and the inverter/charger is correctly connected, and ring terminals are tightly screwed to the battery terminals.
Battery Connection Diagram
Exploded view showing how to connect battery ring terminals to the inverter's battery input ports.

WARNING: Shock Hazard! Installation must be performed with care due to high battery voltage in series.

CAUTION!! Do not place anything between the flat part of the inverter terminal and the ring terminal. Otherwise, overheating may occur.

CAUTION!! Do not apply anti-oxidant substance on the terminals before terminals are connected tightly.

CAUTION!! Before making the final DC connection or closing the DC breaker/disconnector, be sure positive (+) must be connected to positive (+) and negative (-) must be connected to negative (-).

4.5. AC Input/Output Connection

CAUTION!! Before connecting to the AC input power source, please install a separate AC breaker between the inverter and the AC input power source. This will ensure the inverter can be securely disconnected during maintenance and fully protected from overcurrent of AC input. The recommended spec of AC breaker is 32A for 3.0KW and 40A for 4.0KW.

CAUTION!! There are two terminal blocks with "INPUT" and "OUTPUT" markings. Please do NOT mis-connect input and output connectors.

WARNING! All wiring must be performed by qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for AC input connection. To reduce risk of injury, please use the proper recommended cable size as below.

Suggested Cable Requirement for AC Wires
ModelGaugeTorque Value
3.0KW10 AWG1.2~1.6 Nm
4.0KW8 AWG1.4~1.6 Nm

Follow these steps to implement AC input/output connection:

  1. Before making AC input/output connection, be sure to open the DC protector or disconnector first.
  2. Remove insulation sleeve 10mm for six conductors. Shorten phase L and neutral conductor N by 3 mm.
  3. Insert AC input wires according to polarities indicated on the terminal block and tighten the terminal screws.
AC Input/Output Connection Diagram
Diagram illustrating the connection of AC input and output wires to the inverter's terminal blocks, indicating L (Line), N (Neutral), and Ground (PE) connections.

WARNING: Be sure that the AC power source is disconnected before attempting to hardwire it to the unit.

  1. Then, insert AC output wires according to polarities indicated on the terminal block and tighten the terminal screws. Be sure to connect the PE protective conductor (Ground, green) first.
  2. Make sure the wires are securely connected.

CAUTION: Important! Be sure to connect AC wires with correct polarity. If L and N wires are connected reversely, it may cause utility short-circuited when these inverters are worked in parallel operation.

CAUTION: Appliances such as air conditioners require at least 2-3 minutes to restart to balance refrigerant gas inside of circuits. If a power shortage occurs and recovers quickly, it can damage connected appliances. Check if your air conditioner has a time-delay function. Otherwise, the inverter/charger may trigger an overload fault to protect the appliance, but internal damage may still occur.

4.6. PV Connection

CAUTION: Before connecting to PV modules, please install separately a DC circuit breaker between the inverter and PV modules.

WARNING! All wiring must be performed by qualified personnel.

WARNING! It's very important for system safety and efficient operation to use appropriate cable for PV module connection. To reduce risk of injury, please use the proper recommended cable size as below.

Suggested Cable Requirement for PV Wires
ModelWire SizeCable (mm²)Torque Value (max)
3.0KW/4.0KW1 x 12AWG41.2 Nm

PV Module Selection: When selecting proper PV modules, consider these parameters:

  1. Open circuit Voltage (Voc) of PV modules must not exceed the max. PV array open circuit voltage of the inverter.
  2. Open circuit Voltage (Voc) of PV modules should be higher than the min. PV Array MPPT Voltage range.
PV Module Voltage Ranges
INVERTER MODEL3.0KW4.0KW
Max. PV Array Open Circuit Voltage350Vdc
PV Array MPPT Voltage Range55Vdc~350Vdc

Follow these steps to implement PV module connection:

  1. Remove insulation sleeve 10 mm for positive and negative conductors.
  2. Check correct polarity of connection cable from PV modules and PV input connectors. Then, connect the positive pole (+) of the connection cable to the positive pole (+) of the PV input connector. Connect the negative pole (-) of the connection cable to the negative pole (-) of the PV input connector.
PV Module Connection Diagram
Diagram showing the connection of PV module wires to the inverter's PV input connectors, emphasizing correct polarity.
  1. Make sure the wires are securely connected.

4.7. Final Assembly

After connecting all wirings, please put the bottom cover back by screwing the two screws.

Final Assembly Diagram
Illustration of the inverter with its bottom cover re-attached after wiring.

5. Operation

5.1. Power ON/OFF

Once the unit has been properly installed and the batteries are connected, simply press the On/Off switch (located on the bottom of the case) to turn on the unit.

Power ON/OFF Switch
Image showing a hand pressing the ON/OFF switch on the inverter.

5.2. Operation and Display Panel

The operation and display panel, located on the front of the inverter, includes three indicators, four function keys, and an LCD display. These components show the operating status and input/output power information.

Operation and Display Panel
Close-up of the PowMr hybrid inverter's front panel, highlighting the LCD display and control buttons (ESC, UP, DOWN, ENTER).
LED Indicator Messages
LED IndicatorColorStatusMessages
AC/INVGreenSolid OnOutput is powered by utility in Line mode.
FlashingOutput is powered by battery or PV in battery mode.
CHGGreenSolid OnBattery is fully charged.
FlashingBattery is charging.
FAULTRedSolid OnFault occurs in the inverter.
FlashingWarning condition occurs in the inverter.
Function Keys
Function KeyDescription
ESCTo exit setting mode
UPTo go to previous selection
DOWNTo go to next selection
ENTERTo confirm the selection in setting mode or enter setting mode

5.3. LCD Display Icons

The LCD displays various icons to provide information about the inverter's status, input sources, configuration, faults, output, and battery.

LCD Display Icons and Descriptions
IconFunction Description
ACIndicates the AC input.
PVIndicates the PV input.
INPUT/BATTERY (with values)Indicates input voltage, input frequency, PV voltage, battery voltage, and charger current.
Gear iconIndicates the setting programs.
Warning/Fault iconIndicates the warning and fault codes.
Warning (flashing)Flashing with warning code.
Fault (solid)Solid lighting with fault code.
OUTPUT/LOAD (with values)Indicates output voltage, output frequency, load percent, load in VA, load in Watt, and discharging current.
Battery icon (flashing bar)Left side flashing bar and battery icon indicates battery level by 0-20%, 20-40%, 40-60%, and 80-100% in battery mode and charging status in line mode.
OVER LOADIndicates overload. Right side flashing bar and load icon indicates the load level by 0-24%, 25-50%, 50-75%, and 75-100%.
Mains connection iconIndicates unit connects to the mains.
PV panel iconIndicates unit connects to the PV panel.
BYPASSIndicates load is supplied by utility power.
Utility charger iconIndicates the utility charger circuit is working.
DC/AC inverter iconIndicates the DC/AC inverter circuit is working.
Mute iconIndicates unit alarm is disabled.

5.4. LCD Setting

After pressing and holding the ENTER button for 3 seconds, the unit will enter setting mode. Use the "UP" or "DOWN" buttons to select setting programs. Then, press "ENTER" to confirm the selection or "ESC" to exit.

LCD Setting Programs (Partial)
ProgramDescriptionSelectable OptionDetails
00Exit setting mode00 ESCExits the setting menu.
01Output source priority01 S06 (Solar first)Solar energy provides power to loads as first priority. If solar energy is insufficient, utility power supplies loads.
01 S60 (SBU priority)Solar energy provides power to loads as first priority. If solar energy is insufficient, battery energy supplies loads. Utility power supplies loads only when battery voltage drops below warning or setting point (program 13).
02Maximum charging current02 10A to 02 140AConfigures total charging current for solar and utility chargers. (Max. charging current = utility charging current + solar charging current)
03AC input voltage range03 APL (Appliances)Acceptable AC input voltage range: 90-140 VAC.
03 UPS (UPS)Acceptable AC input voltage range: 90-140 VAC.
04Power saving mode enable/disable04 SdS (Disable)Inverter output is not affected by load level.
04 SEn (Enable)Inverter output turns off when connected load is very low or not detected.
05Battery type05 AGn (AGM)Flooded battery type.
05 FLd (Flooded)Flooded battery type.
05 LIb (Lithium)Floating charge cancelled. Battery charge voltage and low DC cut-off voltage can be set in programs 26 and 29.
05 USE (User-Defined)Battery charge voltage and low DC cut-off voltage can be set in programs 26, 27, and 29.
LIb 05 485 (Lithium with communication)If "485" is selected, programs 12, 13, 29 are converted to display SOC.
06Auto restart when overload occurs06 LFd (Restart disable)Disables auto restart.
06 LYE (Restart enable)Enables auto restart.
07Auto restart when over temperature occurs07 LFd (Restart disable)Disables auto restart.
07 EFE (Restart enable)Enables auto restart.
08Output voltage08 120V (default)Sets output voltage to 120V. (Range: 100V, 110V, 120V)
09Output frequency09 50HzSets output frequency to 50Hz.
09 60Hz (default)Sets output frequency to 60Hz.
11Maximum utility charging current11 10A to 11 140ASets the maximum charging current from utility.
12Setting voltage point back to utility source when selecting "SBU priority"12 22.0V to 12 25.5V (24V models)Sets the battery voltage threshold for switching back to utility.
13Setting voltage point back to battery mode when selecting "SBU priority"13 24.0V to 13 29.0V (24V models)Sets the battery voltage threshold for switching back to battery mode.
16Charger source priority16 CSO (Solar first)Solar energy charges battery first. Utility charges only if solar is unavailable.
16 SNU (Solar and Utility)Solar energy and utility charge battery at the same time.
16 OSO (Only Solar)Only solar energy charges battery, regardless of utility availability.
18Alarm control18 bON (Alarm on)Enables audible alarms.
18 bOF (Alarm off)Disables audible alarms.
19Auto return to default display screen19 ESP (Default display)Automatically returns to default display after 1 minute of inactivity.
19 HEP (Stay at latest)Stays on the last viewed screen.
20Backlight control20 LON (Backlight on)Keeps backlight on.
20 LOF (Backlight off)Turns backlight off.
22Beeps while primary source is interrupted22 AON (Alarm on)Enables beeping when primary source is interrupted.
22 AOF (Alarm off)Disables beeping when primary source is interrupted.
25Record Fault code25 FEn (Record enable)Enables fault code recording.
25 FdS (Record disable)Disables fault code recording.
26Bulk charging voltage (C.V voltage)26 28.2V (24V default)Sets the bulk charging voltage. Range: 24.0V-29.2V (24V model), 48.0V-58.4V (48V model). Increment: 0.1V.
27Floating charging voltage27 27.0V (24V default)Sets the floating charging voltage. Range: 24.0V-29.2V (24V model), 48.0V-58.4V (48V model). Increment: 0.1V.
29Low DC cut-off voltage29 21.0V (24V default)Sets the low DC cut-off voltage. Range: 20.0V-24.0V (24V model), 40.0V-48.0V (48V model). Increment: 0.1V.
30Restore default settingsFES 30 ONRestores all settings to factory defaults.
33Battery equalizationE9 33 ONEnables battery equalization. (Only for FLD, USE battery types)
34Battery equalization voltage34 29.2V (24V default)Sets the battery equalization voltage. Range: 25.0V-29.5V (24V model), 50V-59V (48V model). Increment: 0.1V.
35Battery equalized time35 60 (60 min default)Sets the duration of battery equalization. Range: 5-900 min. Increment: 5 min.
36Battery equalized timeout36 120 (120 min default)Sets the timeout for battery equalization. Range: 5-900 min. Increment: 5 min.
37Equalization interval37 30d (30 days default)Sets the interval between battery equalizations. Range: 0-90 days. Increment: 1 day.
39Equalization activated immediately39 on (Enable)Activates battery equalization immediately.

5.5. Lithium Battery Connection

If the inverter is matched with lithium batteries, only lithium batteries that have been matched with the BMS communication protocol are allowed to be used.

Follow these steps to implement lithium battery connection:

  1. Assemble battery ring terminal based on recommended battery cable and terminal specifications.
  2. Insert the ring terminal of battery cable flatly into battery connector of inverter and make sure the bolts are tightened with torque of 2-3Nm. Make sure polarity at both the battery and the inverter/charge is correctly connected and ring terminals are tightly screwed to the battery terminals.
  3. Connect the RJ45 connector to the COMM port on the inverter.
  4. Connect the other end of the RJ45 plug to the battery communication port (RS485). Ensure that the battery signal cable RS485-A is connected to the RS485-A of the COMM port, and the battery signal cable RS485-B is connected to the RS485-B of the COMM port.

Note: If choosing a lithium battery, make sure to connect the BMS communication cable between the battery and the inverter. You need to choose battery type as "Lib-485" mode.

5.5.1. Lithium Battery Communication and Setting

To communicate with the battery BMS, you should set the battery type to "Lib-485" in Program 5.

5.5.2. Connect the end of RJ45 of battery to BMS communication port of inverter

Ensure that the BMS port of the lithium battery corresponds to the pin of the BMS communication port of the inverter. The pin of the inverter BMS interface is defined as shown in the following figure:

Communication Port Pin Definition
Diagram showing the RJ45 communication port on the inverter and its pin assignments (RX, TX, VCC, RS485-A, RS485-B, GND).
Communication Port Pin Definition
Pin numberDefinition
1RX
2TX
3VCC
4VCC
5RS485-A
6RS485-B
7GND
8GND

Note: When communication fails, the LCD will display error code 61, and the inverter will cut off output. If the communication protocol does not match, you can select "LIB" mode.

5.5.3. Lithium Battery Information Display

After pressing and holding the "ESC" button for 3 seconds, enter the lithium battery page. The initial display interface shows the total battery voltage and remaining battery capacity.

Lithium Battery Information Display Content
LCD Data on the LeftLCD Data on the RightInstruction
Total battery voltageRemaining battery capacity
Battery charging currentBattery discharge current
Battery capacityBattery charge/discharge timesWarning in the middle
BMS board temperatureMosfet temperature of BMS board
Maximum voltage of a single battery cellMinimum voltage of a single battery cell
Maximum temperature of a single battery cellMinimum temperature of a single battery cell

5.6. Display Setting

The LCD display information will be switched by pressing the "UP" or "DOWN" key. The selectable information includes input voltage, input frequency, PV voltage, MPPT charging current, MPPT charging power, battery voltage, output voltage, output frequency, load percentage, load in VA, load in Watt, DC discharging current, and main CPU Version.

5.7. Operating Mode Description

The inverter operates in various modes, providing different power supply behaviors. The LCD display will show the current operating mode.

Operating Mode Descriptions
Operation ModeDescriptionLCD Display
Standby mode / Power saving modeNo output is supplied by the unit, but it can charge batteries.Charging by utility and PV energy, Charging by utility, Charging by PV energy, No charging.
Fault modeErrors due to internal circuit or external reasons (e.g., over temperature, output short circuit). Red fault indicator is solid, buzzer alarm sounds. Inverter disconnects all inputs and outputs.Over-temperature, Output low voltage, Output overcurrent, Battery low.
Line ModeThe unit provides output power from the mains and charges the battery.Charging by utility and PV energy, Charging by utility, Power from utility.
Battery ModeThe unit provides output power from battery and PV power.Power from battery and PV energy, PV energy supplies power and charges battery, Power from battery only, Power from PV energy only.

5.8. Battery Equalization Description

The equalization function is added to the charge controller to reverse the buildup of negative chemical effects like stratification and to remove sulfate crystals from the battery plates. This process helps maintain the overall capacity of the battery.

5.8.1. How to Apply Equalization Function

You must enable the battery equalization function in monitoring LCD setting program 33 first. Then, you may apply this function by either:

  1. Setting the equalization interval in program 37.
  2. Activating equalization immediately in program 39.
5.8.2. When to Equalize

In the float stage, when the setting equalization interval (battery equalization cycle) is reached, or equalization is activated immediately, the controller will enter the Equalize stage.

Battery Equalization Graph 1
Graph illustrating the battery equalization process, showing Equalize Voltage, Float Voltage, and stages like BULK, ABSORPTION, FLOAT, and EQUALIZE.
5.8.3. Equalize Charging Time and Timeout

In the Equalize stage, the controller will supply power to charge the battery as much as possible until the battery voltage reaches the battery equalization voltage. Then, constant-voltage regulation is applied to maintain the battery voltage at the battery equalization voltage. The battery will remain in the Equalize stage until the setting battery equalized time is reached.

Battery Equalization Graph 2
Graph showing the battery equalization process with Equalize Charging Time, Absorption Voltage, Float Voltage, and stages.

However, in the Equalize stage, if the battery equalized time expires and the battery voltage doesn't rise to the battery equalization voltage point, the charge controller will extend the battery equalized time until the battery voltage achieves the battery equalization voltage. If the battery voltage is still lower than the battery equalization voltage when the battery equalized timeout setting is over, the charge controller will stop equalization and return to the float stage.

6. Troubleshooting

6.1. Fault Reference Code

The following table lists fault codes and their corresponding events.

Fault Reference Codes
Fault CodeFault EventIcon on
01Fan is locked when inverter is off.
02Over temperature
03Battery voltage is too high
04Battery voltage is too low
05Output short circuited or over temperature is detected by internal converter components.
06Output voltage is too high.
07Overload time out
08Bus voltage is too high
09Bus soft start failed
11Main relay failed
51Over current or surge
52Bus voltage is too low
53Inverter soft start failed
55Over DC voltage in AC output
56Battery connection is open
57Current sensor failed
58Output voltage is too low

6.2. Warning Indicator

The following table lists warning codes and their corresponding events and audible alarms.

Warning Indicators
Warning CodeWarning EventAudible AlarmIcon Flashing
01Fan is locked when inverter is on.Beep twice every second
03Battery is over-chargedBeep twice every second
04Low batteryBeep twice every second
07OverloadBeep twice every second
10Output power deratingBeep twice every second
12Solar charger stops due to low battery.
13Solar charger stops due to high PV voltage.
14Solar charger stops due to overload.
15PV is weak
61When the battery communication is abnormal, stop charging and discharging.

6.3. Troubleshooting Table

This table provides solutions for common issues encountered with the inverter charger.

Troubleshooting Guide
ProblemLCD/LED/BuzzerExplanation / Possible CauseWhat to Do
Unit shuts down automatically during startup process.LCD/LEDs and buzzer active for 3 seconds, then complete off.The battery voltage is too low (<1.91V/Cell)1. Re-charge battery.
2. Replace battery.
No response after power on.No indication.1. Battery voltage is far too low (<1.4V/Cell)
2. Battery polarity is connected reversed.
1. Check if batteries and wiring are connected well.
2. Re-charge battery.
3. Replace battery.
Input voltage displayed as 0 on LCD and green LED is flashing.Input protector is trippedCheck if AC breaker is tripped and AC wiring is connected well.
Mains exist but the unit works in battery mode.Green LED is flashing.Insufficient quality of AC power (Shore or Generator)1. Check if AC wires are too thin and/or too long.
2. Check if generator (if applied) is working well or if input voltage range setting is correct (UPS Appliance).
Green LED is flashing.Set "Solar First" as the priority of output source.Change output source priority to Utility first.
When the unit is turned on, internal relay is switched on and off repeatedly.LCD display and LEDs are flashingBattery is disconnected.Check if battery wires are connected well.
Fault code 07Overload error. The inverter is overload 110% and time is up.Reduce the connected load by switching off some equipment.
Fault code 05Output short circuited.
Temperature of internal converter component is over 120°C.
Check if wiring is connected well and remove abnormal load.
Check whether the air flow of the unit is blocked or whether the ambient temperature is too high.
Fault code 02Internal temperature of inverter component is over 100°C.Return to repair center.
Buzzer beeps continuously and red LED is on.Battery is over-charged.Check if spec and quantity of batteries are meet requirements.
Fault code 01Fan faultReplace the fan.
Fault code 06/58Output abnormal (Inverter voltage below 190Vac or higher than 260Vac)1. Reduce the connected load.
2. Return to repair center.
Fault code 08/09/53/57Internal components failed.Return to repair center.
Fault code 51Over current or surge.Restart the unit, if the error happens again, please return to repair center.
Fault code 52Bus voltage is too low.
Fault code 55Output voltage is unbalanced.
Fault code 56Battery is not connected well or fuse is burnt.If the battery is connected well, please return to repair center.

7. Specifications

Detailed technical specifications for the PowMr 4KW 120V Off-Grid Solar Inverter Charger are provided in the tables below.

Table 1: Line Mode Specifications
INVERTER MODEL3.0KW/24V4.0KW/24V
Input Voltage WaveformSinusoidal (utility or generator)
Nominal Input Voltage120Vac
Low Loss Voltage95Vac±5V(UPS); 65Vac±7V(Appliances)
Low Loss Return Voltage100Vac±5V(UPS); 70Vac±5V(Appliances)
High Loss Voltage140Vac±5V
High Loss Return Voltage135Vac±5V
Max AC Input Voltage150Vac
Nominal Input Frequency50Hz / 60Hz (It can be set in program 09)
Low Loss Frequency45±1Hz/55±1Hz
Low Loss Return Frequency47±1Hz/57±1Hz
High Loss Frequency55±1Hz/65±1Hz
High Loss Return Frequency53±1Hz/63±1Hz
Output Short Circuit ProtectionLine mode: Circuit Breaker
Battery mode: Electronic Circuits
Efficiency (Line Mode)>95% (Rated R load, battery full charged)
Transfer Time10ms typical (UPS); 20ms typical (Appliances)
Table 2: Inverter Mode Specifications
INVERTER MODEL3.0KW/24V4.0KW/24V
Rated Output Power3.0KW4.0KW
Output Voltage WaveformPure Sine Wave
Output Voltage Regulation120Vac±5%
Output Frequency60Hz or 50Hz
Peak Efficiency94%
Overload Protection5s@≥150% load; 10s@110%~150% load
Surge Capacity2* rated power for 5 seconds
Nominal DC Input Voltage24Vdc
Cold Start Voltage23.0Vdc
Low DC Warning Voltage22.0Vdc
Low DC Warning Return Voltage23.0Vdc
Low DC Cut-off Voltage21.0Vdc
High DC Recovery Voltage29Vdc
High DC Cut-off Voltage31Vdc
No Load Power Consumption<35W
Table 3: Charge Mode Specifications
INVERTER MODEL3.0KW/24V4.0KW/24V
Charging Current (UPS) @ Nominal Input Voltage80A110A
Bulk Charging VoltageFlooded Battery29.2Vdc
AGM / Gel Battery28.2Vdc
Floating Charging Voltage27Vdc
Charging Algorithm3-Step
Solar Charging Mode
Rated Power5600W
PV Charge Current100A140A
Efficiency98.0% max.
Max. PV Array Open Circuit Voltage350Vdc
PV Array MPPT Voltage Range55-350Vdc
Standby Power Consumption2W
Battery Voltage Accuracy+/-0.3%
PV Voltage Accuracy+/-2V
Charging Algorithm3-Step
Table 4: General Specifications
INVERTER MODEL3.0KW/24V4.0KW/24V
Safety CertificationCE
Operating Temperature Range0°C to 55°C
Storage temperature-15°C~60°C
Dimension (D*W*H), mm400*250*89mm
Net Weight, kg7.5kg8.5kg

7.1. Appendix: Approximate Back-up Time Table

This table provides approximate back-up times for different loads and battery capacities.

Approximate Back-up Time Table (4.0KW Model)
ModelLoad (W)Backup Time @ 24Vdc 100Ah (min)Backup Time @ 24Vdc 200Ah (min)
4.0KW3004491100
600222525
900124303
120095227
150068164
180056126
210048108
24003594
27003174
32002867

Note: Backup time depends on the quality of the battery, age of battery, and type of battery. Specifications of batteries may vary depending on different manufacturers.

* Product technical specifications are subject to change without notice.

8. User Tips

  • Easy Wi-Fi Setup: Many users find the Wi-Fi configuration straightforward, and the accompanying app is user-friendly for monitoring.
  • Solid Build: The inverter is noted for its robust and solid construction.
  • Grid Testing: The inverter performs excellently when tested with grid power.

9. Warranty and Support

For detailed warranty information, technical support, or service, please contact PowMr customer service.

Contact Information:

  • Tel/Fax: +86 755-28219903
  • Email: Support@powmr.com
  • Web: www.powmr.com
  • Address: Henggang Street, Longgang District, Shenzhen, Guangdong, China

For a complete and detailed user guide, including additional diagrams and instructions, please refer to the official PDF manual available at: PowMr Solar Inverter Charger User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.