ZEFIORA M10

Contents

Zefiora M10 Electric Bicycle User Manual

Model: M10 | Brand: ZEFIORA

Introduction

Congratulations on your purchase of the Zefiora M10 Electric Bicycle! This user manual is designed to guide you through the assembly, operation, and maintenance of your new e-bike. Please read all the information carefully before riding to ensure a safe and enjoyable experience.

This manual is a general version, using a 48V 10Ah battery capacity as an example. Specific parameters may vary depending on the product you purchased.

NOTE TO ALL RIDERS UNDER 18 YEARS OF AGE:

It is very important that you obtain parental permission before riding your electric bike.

For any questions, please feel free to contact us at ebikesservice@outlook.com. We will reply and solve the problem for you within 24 hours.

Product Safety Notice & Warning Message

Don't Ride Until You Read This:

  • Always wear a helmet when riding your electric bike.
  • Keep the two keys properly. If the unique keys are lost, you will not be able to turn on the bike or replace the battery. If necessary, you should get more spare keys (Note: a backup key is not provided).
  • Make sure your electric bike has a full battery before taking it out to ride.
  • Always be aware of local road laws and follow them.
  • Do not ride the bike under the influence of drugs or alcohol.
  • Always respect pedestrians.
  • Do not ride under wet conditions. The electric bike may slide from under your feet causing injury. Wet conditions may damage the electronics and void the warranty.

Important Warnings:

  1. Avoid water: The electric bike is not waterproof. The electronics may be damaged due to water, and water damage is not covered by our warranty. Riding in wet conditions is also very dangerous and may result in injury.
  2. Avoid prolonged exposure to sun or rain and avoid storage in places with high temperatures or corrosive gas.
  3. Abuse: We do not cover physical damage due to negligent care and extreme riding.
  4. Whenever you ride the Electric Bike, you risk severe injury or even death from loss of control, collisions, and falls. Use caution and ride at your own risk.
  5. Do not modify the product from the manufacturer's original design.
  6. Do not exceed the posted speed limit and obey all traffic laws.
  7. Avoid touching the charging port directly and do not let it make contact with a metal object.
  8. Keep hands and all body parts away from moving parts while operating the electric bike.
  9. Before riding, be sure to check the electric bike over and make sure it is operating correctly before each use.
  10. Before riding, be sure to check that the braking system is functioning properly and that all safety labels are in place and you understand the safety warnings.
  11. Before riding, be sure that any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition.
  12. Before riding, be sure to check that the tires are in good condition, inflated properly, and have sufficient tread remaining.
  13. The electric bike should never be used by children under the age of 18.
  14. Make note that additional insurance may be required to cover situations you encounter while riding an electric bike. It is recommended that you contact an insurance company or broker for advice and consultation.
  15. To conserve electricity, use assist mode, and avoid zero starting, frequent braking, driving against the wind, carrying heavy loads including other people and riding with insufficient air pressure.

Package Contents

Carefully check the package contents. If anything is missing or damaged, please contact Electric Bike customer service for support at ebikesservice@outlook.com.

Unpack the bike: Open the bike box and remove the small box inside. With the help of another person capable of safely lifting a heavy object, remove the bike from the bike box. Carefully remove the packaging material protecting the bike frame and components. Please recycle packaging materials, especially cardboard and foam, whenever possible. Open the small box and carefully set out all contents.

Zefiora M10 Electric Bicycle and components
Zefiora M10 Electric Bicycle and various components

Included Items:

  • User Manual x1
  • Seat x1
  • Pedals x2
  • 2x Wrenches
  • 3x Allen Key Wrenches
  • Kickstand x1
  • Keys x2
  • Front Wheel x1
  • Charger x1
  • Fender x2
  • Electric Bike x1

Setup (Assembly)

If you are still unable to install after reading these instructions, you can contact the customer service of the platform you purchased from. We will guide you through the installation and send you a video.

Video: Zefiora M10 Electric Bicycle Installation Guide.

Step 1: Front Fork Assembly

  1. Remove the front wheel and install it on the front fork.
  2. Then install the front wheel anti-spin hook and nut, and tighten them.
Front fork assembly step 1
Front fork assembly: Removing the front wheel.
Front fork assembly step 2
Front fork assembly: Installing the front wheel.

Step 2: Fender & Headlight Installation

  1. Take out the fender, remove the nut, washer, and bolt at the top of the front fork.
  2. Fix the headlight and fender to the fixed position on the front fork with screws.
  3. Use a cross screwdriver to loosen the screw at the rear mudguard clip position, then separate the clip by hand and hook it under the saddle tube clamp.
  4. Adjust to the proper position and tighten the screws with a cross screwdriver to secure the mudguard.
Fender and headlight installation step 1
Fender and headlight components.
Fender and headlight installation step 2
Attaching headlight and fender to front fork.
Fender and headlight installation step 3
Loosening rear mudguard clip screw.
Fender and headlight installation step 4
Securing the mudguard.

Step 3: Stem Assembly

  1. Loosen the screws to remove the front fork sleeve.
  2. Take out the stem and insert it into the front frame.
  3. Tighten the screws to fix the stem in place.
  4. After making sure the stem is aligned with the direction of the tire, tighten the clamping screws below the stem to fix the direction.

Step 4: Kickstand Installation

  1. First, you need a screwdriver to fix the screws on the kickstand.
  2. Secure the kickstand to the designated position of the bike.
  3. Finally, fix the screws on the left side, making sure they are locked to prevent them from falling off during riding.

Step 5: Pedals Installation

  1. Locate the right-side / left-side pedal, which is marked "R" / "L" and should have an "R" / "L" sticker attached.
  2. Thread the right pedal onto the right crank gently by hand, turning clockwise. Then tighten the pedal with an Allen wrench.
  3. Thread the left pedal onto the left crank gently by hand, turning counter-clockwise. Then tighten the pedal with an Allen wrench.
  4. Check the chain alignment. Rotate the right pedal and crank toward the back of the bike as though pedaling backward. Watch the chain and ensure it runs smoothly through the drivetrain (rear cog, chain tensioner, and around the front chain ring).

Note: If the pedal/chain doesn't run smoothly or something seems misaligned, please contact Electric Bike Support at support@ride-ebike.com.

Step 6: Seat Installation

  1. Loosen the quick-release screws on the saddle clamp to install the seat post.
  2. Move the seat up and down by sliding the seat post in or out of the seat tube.
  3. Tighten the screws to fix the seat post in place.
  4. After making sure the stem is aligned with the direction of the tire, tighten the clamping screws below the stem to fix the direction.

Positioning the seat at the right height is important for better pedaling, safety, and overall riding comfort. The rider's leg length is used to determine the seat's position. When you pedal, your hips should remain level and your legs should be almost fully extended at the bottom of the pedal stroke, but not over-extended.

To determine the right seat height, sit on the eBike with one pedal at its lowest point and place the ball of your foot on the pedal. Your leg should be almost fully extended (not locked out) with a slight bend at the knee.

NOTICE:

Ensure the seat post and seat are properly adjusted before riding. DO NOT raise the seat post beyond the lowest insertion marking etched into the seat post tube. If the seat post is extended past these markings, the seat post or frame may break, potentially harming the rider and damaging the bike irreparably. Ensure the lowest insertion markings on the seat post are INSIDE the seat-tube of the frame.

Seat post with minimum insertion mark visible
Correct seat post insertion (mark not visible).
Seat post with minimum insertion mark exposed
Incorrect seat post insertion (mark exposed).

Before using the bike, always check that the latches, levers, and quick releases are properly secured and undamaged. Ensure that they are correctly secured before every ride and after every time the bike is left unsupervised, even momentarily. Otherwise, the handlebar stem and/or seat post may come loose and result in loss of bike control, damage to the rider and/or bike, additional property damage, serious injury, and/or death.

Battery Management

Removing the Battery:

  1. Insert the key into the lock and turn it counterclockwise to the left. The battery will pop out.
  2. Prop up the battery with your left hand and then remove the battery with both hands.
Inserting key to unlock battery
Inserting key to unlock battery.
Turning key to unlock battery
Turning key to unlock battery.
Battery popping out after unlocking
Battery popping out after unlocking.
Removing battery with both hands
Removing battery with both hands.

When the battery is removed, be careful not to drop or damage it when loose from the bike. Avoid damaging the exposed connector terminals and keep them clear of debris.

Installing the Battery:

Ensure the battery is turned off before sliding it into the frame mount receptacle. Do not force the battery onto the receptacle; slowly align and push the battery down into the receptacle. Ensure the battery has been properly secured to the bike before each use by carefully pulling upwards on the battery with both hands to test the security of the attachment of the battery to the mount.

Charging Your E-Bike:

Before using the electric bike, you must fully charge the battery.

Zefiora M10 Ebike charging setup
Zefiora M10 Ebike with battery charging setup.
  1. Ensure the battery is off by rotating the key to align with the off icon.
  2. Remove the rubber cover on the charging port on the opposite side of the battery from the key switch.
  3. Plug the charger into the battery's charging port. With the battery on or off the bike, place the charger in a flat, secure place, and connect the DC output plug from the charger to the charging port on the side of the battery.
  4. Plug the charger into a power outlet. Charging should initiate and will be indicated by the LED charge status lights on the charger turning red. Once fully charged, the charging indicator light turns green. Unplug the charger from the wall outlet first and then remove the charger output plug from the battery charging port.

Operating Instructions

Display and Settings:

LCD display and gear shifter on handlebar
LCD display and gear shifter.
Light and horn buttons on handlebar
Light and horn buttons.

Instrument Operating Instructions:

  1. Power on/off: Press and hold the "Power on" button for 2 seconds to power on or off.
  2. Gear shifting: Double-click the "Function Key" to cycle through gears 1-3.
  3. Kilometers/miles switch: Triple-click the function key to switch between kilometers/miles and public miles.
  4. Zero/Non-Zero Startup: Five presses of the "Function Key" button to switch between zero and non-zero startup.
  5. Parameter Setting: Simultaneously press the "Function Key" and "Power Key" for 5 seconds to enter parameter setting mode.

Parameter Settings (P01-P04):

  • [P01] Wheel Diameter: After clicking the "Power button" to switch to P2, click the "Function button" to enter the 5-32 wheel diameter selection. Click the "Power button" again to confirm the default 14.
  • [P02] Gear Options: After clicking the "Power Button" to switch to P3, click the "Function Key" to enter gear 03/05. Then click the "Power Button" to confirm the default 03.
  • [P03] Mileage Conversion: After clicking the "Power Button" to switch to P4, click the "Function Key" to enter 00/01. Select and click the "Power Button" again to confirm the default 00.
  • [P04] Speed Limit: After clicking the "Power button" to switch to P5, click the "Function key" to select 25-90, then click the "Power button" to confirm the default 25.

Automatic shutdown after 5 minutes of inactivity.

The top button on the handlebar control is the headlight switch, and the bottom one is the horn switch.

Maintenance

Daily Care and Cleaning:

If you see stains on the bike body, wipe them off with a damp cloth. If the stains won't scrub off, put on some toothpaste and brush them with a toothbrush, then wipe them off with a damp cloth.

Notes:

  • Do not clean the bike with alcohol, gasoline, kerosene, or other corrosive and volatile chemical solvents to prevent damage.
  • Do not wash the bike with a high-pressure water spray.
  • During cleaning, make sure that the bike is turned off, the charging cable is unplugged, and the rubber flap is closed, as water leakage may result in electric shock or other major problems.
  • When the bike is not in use, keep it indoors where it is dry and cool. Do not put it outdoors for a long time. Excessive sunlight, overheating, and overcooling accelerate the battery pack's lifespan.

Battery Maintenance:

  1. Use original battery packs; use of other models or brands may bring about safety issues.
  2. Do not touch the contacts. Do not dismantle or puncture the casing. Keep the contacts away from metal objects to prevent short circuits which may result in battery damage or even injuries and deaths.
  3. Use the original power adapter to avoid potential damage or fire.
  4. Mishandling of used batteries may do tremendous harm to the environment. To protect the natural environment, please follow local regulations to properly dispose of used batteries.
  5. After every use, fully charge the battery to prolong its lifespan.

Storage and Disposal:

  1. Please try to store the bike in a cool and dry place between 50°F-77°F (10°C-25°C). In extremely humid environments, the interior of the bike may suffer condensation or even water accumulation, which may damage the battery rapidly. Devices are not intended for use at elevations greater than 2000m above sea level. Prolonged exposure to UV rays, rain, and the elements may damage the enclosure materials. Store indoors when not in use.
  2. In daily use, try to avoid recharging the bike after completely exhausting the battery. If the battery is low, charge it as soon as possible.
  3. Please charge the bike every other month to preserve the battery.

Regular inspection and maintenance are key to ensure bikes function as intended, and to reduce wear and tear on their systems. Recommended service intervals are meant to be used as guidelines. Real-world wear and tear, and the need for service, will vary with conditions of use. We generally recommend inspections, service, and necessary replacements be performed at the time or mileage interval that comes first in the following table.

Interval Inspect Service Replace
Weekly (100-200 mi / 160-321 km)
  • Check drivetrain for proper alignment and function (chain, freewheel, chainring, derailleur).
  • Check wheel trueness and for quiet wheel operation.
  • Check condition of frame for any damage.
  • Clean frame by wiping with damp cloth.
  • Use barrel adjuster(s) to tension derailleur/brake cables if needed.
Replace any components confirmed by Product Support or a certified bike mechanic to be damaged beyond repair or broken.
Monthly (250-750 mi / 402-1207 km)
  • Check brake pad alignment, brake cable tension.
  • Check bike is shifting properly, proper derailleur cable tension.
  • Check chain stretch.
  • Check brake and shifter cables for corrosion or fraying.
  • Check spoke tension.
  • Check accessory mounting (rack mounting bolts, fender hardware, alignment).
  • Clean and lubricate drivetrain.
  • Check crankset and pedal torque.
  • Clean brake and shift cables.
  • True and tension wheels if any loose spokes are discovered.
  • Balance the battery.
  • Replace brake and shift cables if necessary.
  • Replace brake pads if necessary.
Every 6 Months (750-1250 mi / 1207-2011 km)
  • Inspect drivetrain (chain, chainring, freewheel, derailleur).
  • Inspect all cables and housings.
  • Standard tune-up by certified, reputable bike mechanic is recommended.
  • Grease bottom bracket.
  • Replace brake pads.
  • Replace tires if necessary.
  • Replace cables and housings if necessary.

Safety Check (Pre-Ride Checklist):

Before every ride, and after every 35-50 miles (56km-80km), we advise following this pre-ride safety checklist:

Component Checklist
1. Brakes
  • Ensure front and rear brakes work properly.
  • Check brake pads for wear and ensure they are not overworn.
  • Ensure brake pads are correctly positioned in relation to the rims.
  • Ensure brake cables are lubricated, correctly adjusted, and display no obvious wear.
  • Ensure brake levers are lubricated and tightly secured to the handlebar.
  • Test that the brake levers are firm and that the brake, and the brake light are functioning properly.
2. Wheels and Tires
  • Ensure tires are inflated within the recommended limits posted on the tire sidewalls and hold air.
  • Ensure tires have good tread, have no bulges or excessive wear, and are free from any other damage.
  • Ensure rims run true and have no obvious wobbles, dents, or kinks.
  • Ensure all wheel spokes are tight and not broken.
  • Check axle nuts and front wheel quick-release to ensure they are tight. Ensure the locking lever on the quick-release skewer is correctly tensioned, fully closed, and secured.
3. Steering
  • Ensure the handlebar and stem are correctly adjusted, tightened, and allow proper steering.
  • Perform a handlebar twist test (see assembly step 3) to ensure the stem clamp bolt security.
  • Ensure the handlebar is set correctly in relation to the fork and the direction of travel.
4. Chain
  • Ensure the chain is clean, oiled, and runs smoothly.
  • Extra care is required in wet, salty/otherwise corrosive, or dusty conditions.
5. Bearings
  • Ensure all bearings are lubricated, run freely, and display no excess movement, grinding, or rattling.
  • Check headset, wheel bearings, pedal bearings, and bottom bracket bearings.
6. Cranks and Pedals
  • Ensure pedals are securely tightened to the cranks.
  • Ensure the cranks are securely tightened and are not bent.
7. Derailleur and Mechanical Cables
  • Check that the derailleur is adjusted and functioning properly.
  • Ensure shifter and brake levers are attached to the handlebar securely.
  • Ensure all shifter and brake cables are properly lubricated.
8. Frame, Fork, and Seat
  • Check that the frame and fork are not bent or broken. If either is bent or broken, they should be replaced.
  • Check that the seat is adjusted properly, and the seatpost quick-release lever is securely tightened.
9. Motor Drive Assembly and Throttle
  • Ensure the hub motor is spinning smoothly and motor bearings are in good working order.
  • Ensure all power cables running to the hub motor are secured and undamaged.
  • Make sure the hub motor axle bolts are secured and the torque arm, torque arm bolt, and torque washers are in place.
10. Battery
  • Ensure the battery is charged before use.
  • Ensure there is no damage to the battery.
  • Lock the battery to the frame and ensure that it is secured.
  • Charge and store the bike and battery in a dry location, between 50°F-77°F (10°C-25°C).
  • Let the bike dry completely before using again.
11. Electrical Cables
  • Look over connectors to make sure they are fully seated and free from debris or moisture.
  • Check cables and cable housing for obvious signs of damage.
  • Ensure the headlight, taillight, and brake light are functioning, adjusted properly, and unobstructed.
12. Accessories
  • Ensure all reflectors are properly fitted and not obscured.
  • Ensure all other fittings on the bike are properly secured and functioning.
  • Inspect the helmet and other safety gear for signs of damage.
  • Ensure the rider is wearing a helmet and other required riding safety gear.
  • Ensure mounting hardware is properly secured if fitted with a front rack, rear rack, basket, etc.
  • Ensure the taillight and taillight power wire are properly secured if fitted with a rear rack.
  • Ensure the fender mounting hardware is properly secured if fitted with fenders. Ensure there are no cracks or holes in fenders.
  • If installed, ensure the optional rear wheel lock is secured in the unlocked position and the key is removed before every ride.

Tire Inflation and Replacement:

The M10 and M12 models are equipped with 26x2.125 inch tires. The tires are designed for durability and safety for regular cycling activities and need to be checked before each use for proper inflation and condition. Proper inflation, care, and timely replacement will help ensure that your bike's operational characteristics will be maintained, and unsafe conditions avoided.

Recommended 40-65 PSI for the stock tires on the bike. Always stay within the manufacturer's recommended air pressure range as listed on the tire sidewall.

WARNING:

It is critically important that proper air pressure is always maintained in pneumatic tires. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and overinflated tires may burst. Failure to always maintain the air pressure rating indicated on pneumatic tires may result in tire and/or wheel failure.

Inflate your tires from a regulated air source with an available pressure gauge. Inflating your tires from an unregulated air source could overinflate them, resulting in a burst tire.

Even tires equipped with built-in, flat-preventative tire liners, like those that come with bikes, can and do get flats from punctures, pinches, impact, and other causes. When tire wear becomes evident or a flat tire is discovered, tires and/or tubes must be replaced before operating the bike or injury to operators and/or damage to your bike could occur.

WARNING:

When changing a tire or tube, ensure that all air pressure has been removed from the inner tube prior to removing the tire from the rim. Failure to remove all air pressure from the inner tube could result in serious injury.

WARNING:

Using aftermarket tires or inner tubes, not provided by Zefiora, may void your warranty, create an unsafe riding condition, or damage to your bike. If required by law, ensure replacement aftermarket tires have sufficient reflective sidewall striping.

For more information on tire or tube replacement procedures, or questions about tire inflation, contact Support.

Troubleshooting

Symptoms Possible Causes Most Common Solutions
The bike does not work
  1. Insufficient battery power
  2. Faulty connections
  3. Battery not fully seated in tray
  4. Improper turn on sequence
  5. Brakes are applied
  1. Charge the battery
  2. Clean and repair connectors
  3. Install battery correctly
  4. Turn on bike with proper sequence
  5. Disengage brakes
Irregular acceleration and/or reduced top speed
  1. Insufficient battery power
  2. Loose or damaged throttle
  3. Misaligned or damaged magnet ring
  1. Charge or replace battery
  2. Replace throttle
  3. Align or replace magnet ring
The motor does not respond when the bike is powered on
  1. Loose wiring
  2. Loose throttle
  3. Loose motor plug wire
  1. Repair and or reconnect
  2. Tighten throttle
  3. Secure motor plug wire.
Reduced range
  1. Low tire pressure
  2. Low or faulty battery
  3. Driving with too many hills, headwind, braking, and/or excessive load
  4. Battery discharged for long period of time without regular charges, aged, damaged, or unbalanced
  5. Brakes rubbing
  1. Adjust tire pressure
  2. Check connections or charge battery
  3. Assist with pedals or adjust route
  4. Balance the battery; contact tech support if range decline persists
  5. Adjust the brakes
The battery will not charge
  1. Charger not well connected
  2. Charger damaged
  1. Adjust the connections
  2. Replace
Wheel or motor makes strange noises
  1. Loose wheel spokes or rim
  2. Loose motor wiring
  1. Tighten, repair, or replace
  2. Reconnect motor.

You can contact the customer service of the platform you purchased from for further assistance.

Error Codes:

Code Description
E0 Communication Error
E4 Accelerator Error
E5 Brake Error
E6 Hall Sensor Error
E7 Undervoltage Error
E8 Overvoltage Error

Specifications

Item Specifications
Model M10/M12
Product Dimensions 135*22*72 (cm)
Package Dimensions 168*23*98 / 168*25*104 (cm)
E-Bike Weight 50.7lb (23kg) / 55.1lb (25kg)
Battery 48V 10Ah (standard, other capacities available)
Charger 54.6V 2A
Charging Time 3-6 Hours
Tire Pressure 40-65 PSI
Bell/Horn Electric Horn Installed
Frame Material High Carbon Steel (Aluminum alloy also available)
Max Speed 30 - 50 KM/H (25 MPH)
Range per Power 31 - 60 km (45 Miles)
Wattage > 500w (1000W Peak Motor)
Voltage 48V
Power Source Lithium battery
Folded No
Motor Type Brushless
Wheel Size 26 inches (26x2.125)
Rated Passenger Capacity One Seat
Certification CE, UL2849

User Tips

  • Derailleur Adjustment: The derailleur may require adjustment upon arrival. If you experience issues with gears 1, 6, or 7, or any other gears, a fine-tuning adjustment will likely resolve this.
  • Brake Pad Adjustment: Brake pads might rub the disc initially. This is normal and can be adjusted. Refer to the 'How to adjust abnormal brake noise on a bicycle' section for detailed steps.
  • Tire Size: The tire size for the M10 model is 26x2.125 inches. This information is useful for future replacements.
  • Headlight/Horn Control: The control unit for the headlight and horn may sometimes arrive with minor cracks. These can often be fixed with a small amount of super glue.
  • Front Axle: Note that the front axle is a sturdy 10mm thick bolt, not a slim quick-release. The nut fits a 15mm socket.

Frequently Asked Questions (FAQs)

Q1: What if the e-bike arrived missing an accessory or a broken part?
A1: Please take a photo and send it to the Electric Bike Support Team by sending an email to ebikesservice@outlook.com. The team will reply to you soon and send the correct accessory or part replacement.
Q2: Will my bike arrive assembled?
A2: Your bike will arrive mostly assembled. We will also provide the tools and a comprehensive assembly video for the remaining parts.
Q3: What can I do if something goes wrong with my e-bike during the warranty?
A3: We believe that communication is the best way to solve the problem. Please contact us in time. To help you solve the problem as quickly as possible, please describe the problem in detail and provide photos/videos with your order ID to ebikesservice@outlook.com.
Q4: What is the autonomy (range) of the bike?
A4: The range per power is typically 31-60 km (approximately 45 miles), depending on factors like battery capacity (e.g., 10Ah, 15Ah, 17.5Ah), terrain, rider weight, and assist mode usage.
Q5: Does the bike support two batteries?
A5: The standard configuration is for one battery. The manual does not specify support for a second battery. Please contact customer service for specific modifications or dual battery options.

Warranty & Support

This user manual is a general version, using a 48V 10Ah battery capacity as an example. Specific parameters may vary depending on the product you purchase.

For any questions, please feel free to contact us. We will reply and solve the problem for you within 24 hours.

Email: ebikesservice@outlook.com

Your cables, spokes, and chain will stretch after an initial break-in period of 50-100 mi (80-160 km), and bolted connections can loosen. Always have a certified, reputable bike mechanic perform a tune-up on your bike after your initial break-in period of 50-100 mi (80-160 km) (depending on riding conditions such as total weight, riding characteristics, and terrain). Regular inspections and tune-ups are particularly important for ensuring that your bike remains safe and fun to ride.

Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.