KKMOON PPR Welding Machine

Contents

Cordless PPR Water Pipe Melter Plastic Welding Machine

Model: PPR Welding Machine (TT-E22917)

1. Product Information

This manual provides instructions for the safe and efficient use of your Cordless PPR Water Pipe Melter Plastic Welding Machine.

  • Product Name: Water Pipes Melting Device PPR Welding Machine Temperature Adjustment Plastic Pipe Welding Tool
  • Model: TT-E22917
  • Batch/Serial Number: ALI0807543473
  • Brand: KKMOON

2. Safety Information

Please read all safety warnings and instructions carefully before using this device to prevent electric shock, fire, or serious injury.

  • WARNING: To avoid danger of suffocation, keep any plastic packaging away from babies and children.
  • Ensure the work area is well-ventilated.
  • Wear appropriate personal protective equipment, including heat-resistant gloves and eye protection.
  • Do not touch the hot ironing heads during or immediately after use to avoid burns. The anti-scald heat insulation heads are designed to reduce risk, but caution is still required.
  • Ensure the embedded switch design is used to prevent accidental contact and eliminate safety hazards.
  • Do not expose the device to rain or wet conditions.
  • Store the device in a dry, secure place out of reach of children.

3. Setup

Follow these steps to prepare your PPR Water Pipe Melter for use:

  1. Install the Battery: Insert a compatible 21V lithium battery (not included) into the battery slot at the base of the machine. Ensure it clicks securely into place.
  2. Select and Install Welding Heads: The device comes with 20mm, 25mm, and 32mm ironing heads. Choose the appropriate size for your pipe.
    • Put the screw into the hole of the hot head screw.
    • Connect the hot head to the other end.
    • Tighten the screws with a hex wrench to secure the head.
Installation method for welding heads
Figure 1: Step-by-step installation of welding heads.

The device is designed for cordless operation, providing convenience and flexibility without being limited by power supplies.

4. Operating Instructions

This device features a high-power design for quick and efficient heating with uniform and stable heat conduction.

  1. Power On: Press the power button. The digital display will illuminate.
  2. Set Temperature: Use the temperature adjustment buttons to set the desired temperature between 350°C and 450°C. The intelligent temperature control chip ensures uniform heating.
  3. Close-up of temperature adjustment buttons and digital display
    Figure 2: Digital display and temperature adjustment controls.
  4. Preheat: Allow the device to preheat until it reaches the set temperature.
  5. Welding Process: Once heated, the baking paint ironing heads are ready for use. They are designed not to stick to pipes and prevent leakage, offering significant thermal conductivity.
    • The device is suitable for PPR, PE 20#, 25#, 32# hot and cold water pipes.
    • Refer to the following melting points for common pipe materials:
    • PPR: 260 ± 10 °C
    • PB: 240 ± 10 °C
    • PE: 220 ± 10 °C
  6. Precise temperature regulation (350-450°C) and melting points for PPR, PB, PE pipes
    Figure 3: Temperature regulation and pipe material compatibility.
  7. Power Off: After use, turn off the device and allow it to cool completely before handling or storing.
Product in use, showing welding process
Figure 4: Example of the welding machine in operation.

5. Maintenance

Proper maintenance ensures the longevity and performance of your welding machine.

  • Cleaning: After the device has cooled down, wipe the ironing heads and the body of the machine with a clean, dry cloth. Do not use abrasive cleaners or solvents.
  • Storage: Store the device and its accessories in a dry place, away from direct sunlight and moisture.
  • Battery Care: If using a rechargeable battery, follow the battery manufacturer's instructions for charging and storage. Remove the battery if the device will not be used for an extended period.

6. Troubleshooting

If you encounter issues with your welding machine, consider the following:

  • Device not turning on: Ensure the battery is properly inserted and fully charged.
  • Insufficient heating: Verify the temperature setting is correct for the pipe material. Allow sufficient time for preheating.
  • Poor weld quality: Check that the ironing heads are clean and correctly installed. Ensure the pipe ends are clean and properly prepared.

For persistent issues, please contact customer support.

7. Specifications

Feature Specification
Name Water Pipes Melting Device
Material Plastics
Color Black + Blue
Rated Power 350-450W
Rated Voltage 21V
Clamping Size / Tube Diameter 20-32mm
Replacement Heads Size φ20mm / 25mm / 32mm
Dimensions (Item Size) 278 * 116 * 76mm / 10.94 * 4.56 * 2.99in
Weight 530g / 1.17lb
Power Source AC (via battery, not included)
Use Pipes Melting Welding
Origin Mainland China
Product specifications diagram with dimensions
Figure 5: Dimensional specifications of the welding machine.

8. User Tips

  • Battery Compatibility: This device is sold as 'Body without battery'. Ensure you purchase a compatible 21V lithium battery for cordless operation.
  • Ergonomic Design: The anti-slip rubber design and ergonomic soft handle provide a comfortable grip, reducing fatigue during extended use.
  • Versatile Positioning: The welding head can be rotated 360 degrees, allowing for flexible operation in various angles and tight spaces.
  • 360-degree view of the welding machine, highlighting its rotational capability
    Figure 6: The welding machine's 360-degree rotational capability.

9. Manufacturer & Support

Manufacturer Information:

  • Company Name: Dongguan Donggao Electronic Technology Co., Ltd.
  • Full Address: No. 808, Building A, Dingfeng International Plaza, No. 19 Dongtai Dongguan Avenue, Dongcheng District, Dongguan City
  • Email: b229sumaitn2956@163.com
  • Telephone: 86-13376659356

EU Authorized Representative:

  • AR Company Name: SOLID AUTHORITY LIMITED
  • Full Address: IE-51 Bracken Road, Sandyford, Dublin 18, D18 CV48, Ireland
  • Email: phoebe8706@gmail.com
  • Telephone: 353-761441379

A more detailed user manual is available in PDF format for download: User Manual (PDF).

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.