RACBOX 010-03

Contents

RACBOX 12V Bi LED Projector Lens Fog Light User Manual

Model: 010-03

Brand: RACBOX

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your new RACBOX 12V Bi LED Projector Lens Fog Lights. This product is designed as an auxiliary accessory for automotive lighting, intended for normal replacement and upgrade of original car lights. It is crucial to read and understand all instructions before use to ensure proper function and safety.

RACBOX Bi LED Projector Fog Lights installed on a car, showing their 3-inch size.
RACBOX Bi LED Projector Fog Lights installed on a car, showing their 3-inch size.
Video demonstrating the RACBOX Bi LED Projector Fog Lights, showing product rotation and high/low beam patterns.

2. Safety & Warnings

Important Safety Information

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Do not expose to water or moisture.

3. Specifications

Diagram showing detailed product parameters and dimensions of the RACBOX Bi LED Projector Fog Light.
Detailed product parameters and dimensions.
AttributeValue
Item TypeFog Lamp Assembly
Size3.0 Inch (97.7mm/3.84" diameter, 136.2mm/5.36" length)
Color Temperature6000K White
PowerHigh Beam 45W / Low Beam 35W
Luminous Flux10000LM
Waterproof RatingIP67
MaterialsAluminum Housing (High quality 6063 aluminum)
Lifespan≥50000 Hours
Working Voltage12V-15V DC
OriginMainland China
Image illustrating the die-cast aluminum heat sink design of the RACBOX Bi LED Projector Fog Light.
Die-cast aluminum heat sink design for efficient cooling.

4. Setup (Installation Instructions)

Follow these steps carefully for proper installation:

  1. Turn off the vehicle engine and disconnect the power supply to avoid short circuit.
  2. Locate the mounting position of the original fog light.
  3. Remove the fixing screws or clips that hold the stock light assembly.
  4. Unplug the power connector and remove the original fog light.
  5. Install the new fog light assembly into the mounting position.
  6. Secure the light assembly with screws or clips to ensure stable installation.
  7. Connect the power plug correctly. If the light does not work, reverse the plug polarity.
  8. Test all light functions to ensure normal operation.
  9. Recheck all screws and connections to make sure they are firm and reliable.
Wiring diagram for the RACBOX Bi LED Projector Fog Light, showing connections for high beam negative and positive, and the H11 plug.
Wiring diagram: Connect high beam negative and positive, and use the original H11 plug.
Image demonstrating the adjustable nuts for height adjustment of the RACBOX Bi LED Projector Fog Light, with examples of light beam adjustment.
Adjustable nuts allow for precise height adjustment of the light beam.

5. Operating Instructions

The RACBOX Bi LED Projector Lens Fog Lights feature both low beam and high beam functions. Once installed and wired correctly, they operate in conjunction with your vehicle's existing fog light and high beam controls.

  • Low Beam: Activates when your vehicle's fog lights are turned on. Provides a wide, flat beam pattern to illuminate the road directly in front of the vehicle without blinding oncoming traffic.
  • High Beam: Activates when your vehicle's high beams are engaged. Provides a more focused and intense light output for maximum visibility at longer distances.
Image showing the low beam and high beam light patterns projected by the RACBOX Bi LED Projector Fog Lights.
Comparison of low beam (left) and high beam (right) patterns.

6. Maintenance

To ensure the longevity and optimal performance of your fog lights, follow these maintenance guidelines:

  • Cleaning: Regularly clean the lens with a soft, damp cloth to remove dirt and debris. Avoid abrasive cleaners that could scratch the lens.
  • Inspection: Periodically check the mounting hardware and wiring connections to ensure they are secure and free from corrosion or damage.
  • Damage: If the product becomes damaged, discontinue use immediately and replace it.

7. Troubleshooting

Light Not Working

  • Check Power Connection: Ensure the power plug is securely connected. If the light does not work, try reversing the plug polarity.
  • Vehicle Power: Verify that your vehicle's fog light circuit is receiving power. Check fuses if necessary.
  • Wiring: Inspect all wiring for any cuts, pinches, or loose connections.

Improper Beam Pattern

  • Adjustment: Use the adjustable nuts on the light assembly to fine-tune the height of the light beam.
  • Mounting: Ensure the light assembly is securely mounted and not loose or misaligned.

8. User Tips

  • Compatibility Check: Before purchasing or installing, always verify compatibility with your specific vehicle model and year. For example, while these lights are compatible with many Honda models like the Fit, Jazz, and City, it's best to confirm for newer models (e.g., Honda City 2025) with the seller or a professional.
  • Professional Installation: If you are not comfortable with automotive electrical work, it is recommended to have the fog lights installed by a qualified professional.
  • Beam Adjustment: After installation, take the time to properly adjust the beam height to maximize visibility and avoid dazzling other drivers.

9. Warranty & Support

For detailed warranty information and customer support, please refer to the official product documentation or contact the seller directly. A comprehensive user manual in PDF format is available for download:

View User Manual (PDF)

Manufacturer: Guangzhou Bai Ji Tun Trading Co., Ltd

EU Authorized Representative: APEX CE SPECIALISTS LIMITED, UNIT 3D NORTH POINT HOUSE, NORTH POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P, IRELAND

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.