ZEFIORA V10

Contents

ZEFIORA V10 Electric Bike User Manual

Model: V10

1. Important Safety Information

WARNING:

Electric bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle. It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists. Please properly keep this manual and the product certificate of the vehicle.

  • Always Wear A Helmet: Helmets significantly reduce the rate of head injuries. Always wear a helmet that complies with your state laws when riding the E-bike. Check with your local police department for requirements in your community. Make yourself more visible by wearing bright reflective clothing. Keep your reflectors clean and eye protection. Also check your state laws concerning other protective gear that may be required when riding the E-bike.
  • Know Your E-bike: Your new E-bike incorporates many features and functions that have never been built into a bicycle before. Read this manual thoroughly to understand how those features enhance your riding pleasure and safety.
  • Ride Within Your Limits: Take it slow until you are familiar with the riding conditions that you encounter. Be especially careful in wet conditions as traction can be greatly reduced and brakes becoming less effective. Never ride faster than conditions warrant or beyond your riding abilities. Remember that alcohol, drugs, fatigue and inattention can significantly reduce your ability to make good judgement and safely.
  • Keep Your E-bike In Safe Condition: For your safety and enjoyment, and to insure a long life for your E-bike. Inspect and maintain your E-bike regularly. Follow the inspection and maintenance guidelines. Check critical safety equipment before each and every ride.

Disclaimer:

⚠️Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

2. Parts Identification

Familiarize yourself with the main components of your ZEFIORA V10 Electric Bike:

Diagram showing labeled parts of the ZEFIORA V10 Electric Bike, including handlebar, seat, bike frame, light, controller, rear fender, bike motor, derailleur, tire, chain, crank, pedals, battery, front fork, disc brake rotor, LED headlight, front fender, power button, speed mode, and gear adjustment.
Figure 2.1: Main Components of the ZEFIORA V10 Electric Bike
  • Display: Shows speed, battery level, mileage, and gear.
  • Handlebar: Steering control.
  • Bike Frame: Structural support.
  • Seat: Rider's seating.
  • Light: Front and rear illumination.
  • Controller: Manages electrical functions.
  • Rear Fender: Protects from splashes.
  • Bike Motor: Provides electric assistance.
  • Disc Brake Rotor: Part of the braking system.
  • Tire: 20" Fat Tires for various terrains.
  • Derailleur: Manages gear changes.
  • Battery: Power source (48V 15Ah/17.5Ah).
  • Front Fork: Suspension component.
  • Chain: Connects pedals to rear wheel.
  • Crank: Connects pedals to chainring.
  • Pedals: Footrests for propulsion.
  • LED Headlight: Front illumination.
  • Front Fender: Protects from splashes.
  • Power Button: To turn the bike on/off.
  • Speed Mode: Controls power output.
  • Gear Adjustment: Controls mechanical gears.

3. Specifications

Key specifications for the ZEFIORA V10 Electric Bike:

Item Name Product Specification
Model NumberV10
Brand NameZEFIORA
Vehicle Size164*68*115 (CM)
Packing Size136*27*85 (CM)
ColorBlack
Frame MaterialSteel, Aluminum alloy
Net Weight38kg (83.77lb)
Gross Weight46kg (101.41lb)
Max. Support Weight150kg (330lb)
Max Speed>50km/h
Range per Power> 60 km
Wattage> 500w (2000W)
Inner Tire Pressure20PSI / 140KPA
ChargerAC-DC 54.6V 2A 100-240V AC DC5.5X2.1
Battery48V 15Ah / 48V 17.5Ah (Lithium battery)
Brake SystemFront and rear disc brake
Tire Size20x4.0 inch
PedalAluminum alloy pedal
MotorBrushless
Rated Passenger CapacityOne Seat
FoldedNo
CertificationCE

4. Assembly Instructions

The following steps provide a general guide for assembling your electric bike. We recommend consulting a certified bike mechanic for assistance if needed.

4.1. Unpacking and Inventory

Carefully unpack the e-bike from its carton and lay out all contents. Remove all packaging materials protecting the bike frame and components. Please recycle packaging materials appropriately.

Ensure all pieces are included in the package:

  • V10 E-bike
  • Manual(s)
  • Assembly Tool kit
  • Front fender
  • Front Wheel
  • Handlebar
  • Handlebar holder
  • Charger
  • Pedals (marked left and right)
  • Battery Keys (two, identical with number)

4.2. Vehicle Installation Guide

  1. Check whether the outer carton is complete and unpack it.
  2. Take out the bicycle frame.
  3. Take out the accessories and tooling kit.
  4. Use the M5 Allen wrench to unscrew the screw.
  5. Unscrew the screw and remove the trim cover.
  6. Pull out a fixed shelf.
  7. Put the steering in front.
  8. Install retainer and top cover and tighten all screws.
  9. Loosen the screws and remove the lid.
  10. Install the front and tighten all the screws.
  11. Take out the wheels and accessories.
  12. Install the wheels and pay attention to the order of the accessories.
  13. Tighten the screws on both sides.
  14. Install the fender and tighten all the screws.
  15. Identify R for Right Pedal and L for Left Pedal.
  16. Install the pedal and tighten the screw.
  17. Fill the tires with air.
  18. Install the dashboard and tighten all screws.
  19. Connect the ports of cables according to the direction of the arrow.
  20. Press the power button for approximately 3 seconds to turn it on.

Note: It is suggested to check other screws in the frame. If they are loose, you need to tighten them with tools.

Series of images illustrating the assembly steps of the electric bike, including unpacking, installing handlebars, wheels, fenders, pedals, and connecting cables.
Figure 4.1: Visual Guide to Electric Bike Assembly

5. Operating Instructions

5.1. Display Screen Recognition

The display provides crucial information about your ride. Refer to the table below for icon explanations.

Important: Do not set the display without consulting the seller!

Image of the electric bike's display screen showing speed, battery level, and other indicators.
Figure 5.1: Electric Bike Display Interface
Icon Explanation
HeadlampsCurrent state, long press to turn headlights off, long press again to turn headlights on.
BatteryThe battery has a total of ten cells. When the battery decays to one cell and flashes, it needs to be charged.
ErrorThe error icon lights up when there are errors in the vehicle; it does not light up when there are no errors.
SpeedReal-time display of current speed.
WalkWhen this icon lights up, it indicates pedestrian cart mode (max speed 6km/h).
Cruise controlWhen this icon lights up, it indicates the vehicle is in cruise mode.
Gear positionOn the current interface, press the appropriate key to increase or decrease the gear position.
OdometerTotal mileage. Press to switch between single mileage, voltage, and current.

5.2. Gears Operation

Multi-speed bicycles can have internal or derailleur gear systems. Improper shifting can result in the chain jamming or becoming derailed, leading to loss of control or a crash. Always ensure the chain is fully engaged in the desired gear before pedaling hard.

AVOID SHIFTING WHILE STANDING UP ON THE PEDALS OR UNDER LOAD.

To shift properly, pedal the bicycle with little pressure on the pedals, and move the shifter one gear at a time, ensuring the chain is fully engaged in that gear before applying more pressure. For bicycles with 3 front chain rings, avoid "Cross Chaining" (smallest cog in the rear combined with the inner or smallest chain ring in the front, or largest cog in the rear and the outer or largest chain ring in the front). These gear positions put the chain at the most extreme angle and can cause premature wear to the drivetrain. Bicycles with 3 front chain rings have enough gear "overlaps" that these gears are not needed.

Diagram illustrating proper and improper gear chain positions on a bicycle, highlighting 'AVOID THESE GEARS!' for cross-chaining.
Figure 5.2: Gear Operation Diagram, showing gears to avoid (cross-chaining).

5.3. Charging Procedure

Follow these steps to charge your ZEFIORA V10 Electric Bike battery:

  1. Remove the rubber cover on the charging port on the opposite side of the battery from the key switch.
  2. With the battery on or off the bike, place the charger in a flat, secure place, and connect the DC output plug from the charger (round barrel connector) to the charging port on the side of the battery.
  3. Plug the charger into the outlet, then the charging port. Connect the charger input plug (100-240-volt plug) to the power outlet. Charging should initiate and will be indicated by the LED charge status light on the charger turning red.
  4. Unplug the charger from the outlet, then the charging port. Once fully charged (indicated by the charging indicator light turning green), unplug the charger from the wall outlet first and proceed to remove the charger.
Images showing the electric bike battery charging port and the charger unit with indicator lights.
Figure 5.3: Battery Charging Setup

Attention:

Before charging, ensure the charger light faces upwards. A full charge normally takes 3-7 hours. Charge the battery in a clean and safe place and do not overcharge.

  • Red light means the battery is charging.
  • Green light means the battery is fully charged.

Always charge your battery in temperatures between 50°F - 77°F (10°C - 25°C) and ensure the battery and charger are not damaged before initiating charge. If you notice anything unusual while charging, discontinue charging and use of the bike, then contact for help. Do not charge the battery for more than 12 hours at a time or leave a charging battery unattended.

Always charge in dry, indoor locations away from direct sunlight, dirt, or debris. Charge in a clear area away from potential to trip on the charging cords or for damage to occur to the bike, battery, or charging equipment. Do not use with the charger inverted, which can inhibit cooling and reduce charger lifespan.

The battery should be recharged after each use. There is no memory effect, so charging the battery after short rides will not cause damage. Ensure the battery is turned off whenever it is being removed or off the bike. Avoid damaging the exposed connector terminals and keep them clear of debris. Do not touch the "+" and terminal contacts on the bottom of the battery when the battery is removed from the bike.

6. Maintenance

To ensure safe riding conditions and prolong the life of your bike, follow these basic maintenance guidelines:

  1. Properly maintain batteries by keeping them fully charged when between uses of up to two weeks apart. Refer to the manual for long-term battery storage information.
  2. Never immerse or submerge the bike or any components in water or liquid as the electrical system may be damaged.
  3. Periodically check wiring and connectors to ensure there is no damage and that connectors are secure.
  4. To clean, wipe the frame with a damp cloth. If needed, apply a mild non-corrosive detergent mixture to the damp cloth and wipe the frame. Dry by wiping with a clean, dry cloth.
  5. Store under shelter; avoid leaving the bike in the rain or exposed to corrosive materials. If exposed to rain, dry your bike afterwards and apply anti-rust treatment to chain and other unpainted steel surfaces.
  6. Riding on the beach or in coastal areas exposes your bike to salt, which is very corrosive. Wipe down your bike frequently and apply anti-rust treatment. Damage from corrosion is not covered under warranty.
  7. If the hub and bottom bracket bearings have been submerged in water or liquid, they should be taken out and re-greased to prevent accelerated bearing deterioration.
  8. If the paint has become scratched or chipped in the metal, use touch-up paint to prevent rust. Clear nail polish can also be used as a preventative measure.
  9. Regularly clean and lubricate all moving parts, tighten components, and adjust as required.

6.1. Pre-Ride Safety Checklist

Before every ride, and after every 25-45 miles, we advise following this pre-riding safety checklist:

Safety Check Basic Steps
1. Brakes
  • Ensure front and rear brakes work properly.
  • Check brake pads for wear and ensure they are not over-worn.
  • Ensure brake pads are correctly positioned in relation to the rims.
  • Ensure brake control cables are lubricated, correctly adjusted, and display no obvious wear.
  • Ensure brake control levers are lubricated and tightly secured to the handlebars.
  • Test brake levers are firm and that brake, motor cutoff functions, and brake light are functioning properly.
2. Wheels and Tires
  • Ensure tires are inflated to within the recommended limits displayed on the tire sidewalls and holding air.
  • Ensure tires have good tread, no bulges or excessive wear, and are free from any other damage.
  • Ensure rims run true and have no obvious wobbles, dents, or kinks.
  • Ensure all wheel spokes are tight and not broken.
  • Check axle nuts and front wheel quick release skewer is correctly tensioned, fully closed, and secure position.
3. Steering
  • Ensure handlebar and stem are correctly adjusted and tightened and allow proper steering.
  • Ensure the handlebar is set correctly in relation to the forks and the direction of travel.
4. Chain
  • Ensure the chain is oiled, clean, and runs smoothly.
  • Extra care is required in wet, salty/otherwise corrosive, or dusty conditions.
5. Bearings
  • Ensure all bearings are lubricated, run freely, and display no excess movement, grinding, or rattling.
  • Check headset, wheel bearings, pedal bearings, and bottom bracket bearings.
6. Cranks and Pedals
  • Ensure pedals are securely tightened to the cranks.
  • Ensure the cranks are securely tightened and are not bent.
7. Derailleurs
  • Check that the derailleur is adjusted and functioning properly.
  • Ensure shifter and brake levers are attached to the handlebar securely.
  • Ensure all brake and shift cables are properly lubricated.
8. Frame, Fork, and Seat
  • Check that the frame and fork are not bent or broken. If either is bent or broken, they should be replaced.
  • Check that the seat is adjusted properly and the seat post quick release lever is securely tightened.
9. Motor Drive Assembly
  • Ensure hub motor is spinning smoothly and motor bearings are in good working order.
  • Ensure all power cables running to hub motor are secured and undamaged.
  • Make sure the hub motor axle bolts are secured and all torque arms and torque washers are in place.
10. Battery
  • Ensure battery is charged before use.
  • Ensure there is no damage to battery.
  • Lock battery to frame and check to see that it is secured.
  • Charge and store bike and battery in a dry location, between 50°F-77°F.
  • Let bike dry completely before using again.
11. Electrical Cables
  • Look over connectors to make sure they are fully seated, free from debris or moisture.
  • Check cables and cable housing for obvious signs of damage.
  • Ensure headlight, taillight, and brake light are functioning and adjusted properly, and unobstructed.
12. Accessories
  • Ensure all reflectors are properly fitted and not obscured.
  • Ensure all other fittings on bike are properly secured and functioning.
  • Inspect helmet and other safety gear for signs of damage.
  • Ensure rider is wearing helmet and other required riding safety gear.
  • Ensure mounting hardware is properly secured if fitted with a rear rack.
  • Ensure taillight and taillight power wire are properly secured if fitted with a rear rack.
  • Ensure fender mounting hardware is properly secured if fitted with fenders.
  • Ensure there are no cracks or holes in fenders if fitted with fenders.

Your cables, spokes, and chain will stretch after an initial break-in period of 50-100 miles (80-160km), and bolted connections can loosen. Always have a certified, reputable mechanic perform maintenance on your E-bike after this initial break-in period. Regular inspections and tune-ups are particularly important for ensuring that your bike remains safe and fun to ride.

7. Troubleshooting

Refer to the table below for common issues and their solutions:

Symptoms Possible Causes Most Common Solutions
It doesn't work
  • Insufficient battery power
  • Faulty connections
  • Battery not fully seated in tray
  • Improper turn on sequence
  • Brakes are applied
  • Charge the battery
  • Clean and repair connectors
  • Install battery correctly
  • Turn on bike with proper sequence
  • Disengage brakes
Irregular acceleration and/or reduced top speed
  • Insufficient battery power
  • Loose or damaged throttle
  • Charge or replace battery
  • Replace throttle
When powered on the motor does not respond
  • Loose wiring
  • Loose or damaged throttle
  • Loose or damaged motor plug wire
  • Damaged motor
  • Repair and or reconnect
  • Tighten or replace
  • Secure or replace
  • Repair or replace
Reduced range
  • Low tire pressure
  • Low or faulty battery
  • Driving with too many hills, headwind, braking, and/or excessive load
  • Battery discharged for long period of time without regular charges (aged or damaged)
  • Brakes rubbing
  • Adjust tire pressure
  • Check connections or charge battery
  • Assist with pedals or adjust route
  • Replace the battery
  • Adjust the brakes
The battery won't charge
  • Charger not well connected
  • Charger damaged
  • Battery damaged
  • Wiring damaged
  • Adjust the connections
  • Repair or replace
Wheel or motor makes strange noises
  • Damaged motor bearings
  • Damaged wheel spokes or rim
  • Damaged motor wiring
  • Replace
  • Repair or replace
  • Repair or replace motor
Sensor Issue
  • Sensor loose
  • Sensor or cable broken/damaged
  • Adjust the connections
  • Repair or Replace
Pre-load and turn off bike suddenly
  • Battery or motor over heat protection
  • Battery or controller cable loose
  • Battery or controller cable damaged
  • Wait 1-3 minutes to restart e-bike
  • Adjust the connections
  • Repair or Replace

8. User Tips

No specific user tips were available from reviews or Q&A content for this product at this time. Always refer to the safety and maintenance guidelines for optimal performance and longevity.

9. Warranty & Support

For detailed warranty information, return policies, and customer support, please refer to the official user manual PDF provided by the seller. This document contains comprehensive details regarding product guarantees and service procedures.

You can view the official user manual PDF here.

Key service commitments include:

  • Fast Delivery: Expect timely delivery.
  • Delivery Guarantee: A $1.00 coupon code if delivery is delayed, refund if the package is lost, and refund if items are damaged or not delivered within 20 days.
  • Return & Refund Policy: Refer to the seller's specific return and refund policy for details.
  • Security & Privacy: Your personal details are protected and not shared with third parties without consent.

10. Compliance & Disclaimer

Disclaimer: ⚠️Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.