XIAOMI M30S D103CN

Contents

Xiaomi Mijia M30S Omnipotent Robot Mop Vacuum Cleaner D103CN User Manual

Model: M30S D103CN | Brand: XIAOMI

1. Safety Instructions

Please read these instructions carefully and keep them properly before using the product.

1.1. Service Restrictions

  • This product is intended for floor cleaning in domestic settings only. Do not use it outdoors, on non-floor surfaces, or in commercial or industrial environments.
  • This product must not be used by persons with physical, sensory, or intellectual disabilities, or by individuals without relevant experience and knowledge (including children), unless supervised or guided by a guardian to ensure safe use of this product.
  • Do not let children use this product as a toy. Keep children and pets away from the main unit when it is in operation.
  • Do not place children or pets and any items on a stationary or running host.
  • Do not let people or pets approach the main unit while the earth machine is in operation to avoid injury.
  • If the wire assembly is damaged, it must be replaced with a dedicated wire assembly provided by the manufacturer or its service agent.
  • Do not use in a suspended environment without guardrails.
  • Do not place the excavator upside down for extended periods. When handling the main unit, always use the LDS laser sensor protective cover, excavator top cover, and impact buffer plate as handles.
  • Use this product in an environment above 0°C and below 40°C, and ensure the floor is free of any liquids or viscous substances.
  • Do not install, charge, or use the product outdoors, in the bathroom, or around swimming pools.
  • Before use, organize and store all electrical wires in your home. Using them on power lines may cause hazards.
  • Remove fragile items and debris from the floor to prevent damage to valuables during the host's operation.
  • Do not use to sweep any burning objects.
  • Do not let the host inhale hard or sharp objects.
  • Before cleaning and maintaining the host and universal base, turn off the power and unplug the power cord.
  • Do not wipe or rinse the main unit or universal base with wet cloths or liquids. For washable components, ensure they are thoroughly dried after daily cleaning before installation.
  • To transport the product, ensure the main unit is powered off and use the original packaging box.
  • Please use this product in accordance with the instructions in the manual. Any loss or injury resulting from improper use shall be borne by the user.

1.2. Batteries and Charging

  • Do not use any third-party batteries, wiring components, or bases. This product is exclusively compatible with the 1Z2401 universal base.
  • Do not disassemble, repair, or modify the battery or universal base without authorization.
  • Do not place the universal base near heat sources.
  • Do not wipe or clean the rechargeable battery of the universal base with a wet cloth or wet hands. Do not discard used batteries carelessly; they should be handed over to professional recycling institutions for disposal.
  • If the product is not used for an extended period, fully charge it, then turn off the main unit and store it in a cool, dry place. Charge it at least once every 3 months to prevent battery over-discharge.

1.3. Laser Information Security

  • This laser sensor complies with IEC60825-1:2014 Class 1 laser product standards. Avoid direct eye exposure during use.

2. Product Presentation

The Xiaomi Mijia M30S Omnipotent Robot Mop Vacuum Cleaner D103CN is an all-in-one sweeping and mopping robot designed for comprehensive home cleaning. It features a main engine (robot vacuum) and a universal base station for automatic dirt disposal, self-cleaning, and water replenishment.

Xiaomi Mijia M30S Robot Vacuum and Base Station
Figure 2.1: Robot vacuum and its universal base station.

2.1. Main Engine (Robot Vacuum)

The main engine is equipped with various sensors for navigation and cleaning. It performs sweeping, mopping, and suction functions.

Robot vacuum with laser navigation
Figure 2.2: Robot vacuum demonstrating laser navigation for mapping and obstacle avoidance.
Underside view of robot vacuum showing brushes and mop pads
Figure 2.3: Underside view of the robot vacuum, highlighting the main brush, side brush, and rotating mop pads for effective cleaning.

2.1.1. Host and Sensors

The robot vacuum includes:

  • LDS Laser Sensor Protective Cover: Protects the laser sensor.
  • LDS Laser Sensor: For precise navigation and mapping.
  • Linear Laser Sensor: Assists in obstacle detection.
  • Collision Cushion: Absorbs minor impacts.
  • Edge Sensor: Detects edges and prevents falls.
  • Top Cover: Provides access to the dust box.
  • Dust Collection Port: Where dirt is transferred to the universal base.
  • Reset Key: Long press for 3 seconds to restore factory settings.
  • Automatic Water Supply Port for Charging Electrode: Connects to the universal base for water management.
  • Omni-directional Wheel: For smooth movement.
  • Main Brush Cover: Protects the main brush.
  • Main Brush Cover Release Key: For easy access to the main brush.
  • Main Wheel: Drives the robot.
  • Mop Holder Mounting Hole: Where the mop assembly attaches.

2.1.2. Controls and Indicators

The main engine features a central button and indicator light:

  • Heart Button: Long press for 3 seconds to power on/off. Short press to clean or pause. Press and hold to pause/resume charging.
  • Pilot Lamp:
    • White on: Working/Completed/Charging
    • White flashing: Recharging/Repositioning/Upgrading firmware
    • White breathing: Charging (medium to high battery level)
    • Orange always on: Network disconnected
    • Orange flashing: Host status is abnormal
    • Orange breathing: Charging (low battery)
    • Blue flashing: Wi-Fi is connecting
    • Blue Breath: Connecting to Wi-Fi
    • Blue light on for 2 seconds: Wi-Fi connection established

2.2. Universal Base

The universal base is a multi-functional station that handles dirt disposal, mop cleaning, and water management.

Robot vacuum docking with base station
Figure 2.4: The robot vacuum automatically docks with the universal base for charging and self-maintenance.

2.2.1. Components of the Universal Base

  • Sewage Tank: Collects dirty water from mop cleaning.
  • Clear Tank: Holds clean water for mop cleaning and replenishment.
  • Loam Cake: A component related to water management.
  • Handle: For easy carrying of tanks.
  • Cleaning Tray: Where the mop is cleaned.
  • Water Tank Clip: Secures the water tanks.
  • Waterpipe: For water transfer.
  • Rosebox Float/Floater: Sensors for water levels.
  • Dust Collection Bin Cover: Access to the dust bag.
  • Power Interface: For connecting the power cord.

2.2.2. Universal Base Indicators

  • Pilot Lamp:
    • White always on: All-in-One Base in normal status.
    • Orange flashing: All-in-One Base status is abnormal.

2.3. Accessories

The product comes with various accessories to enhance its functionality:

  • Hair and Bristle Integrated Brush
  • Dust Box
  • Side Brush
  • Power Cord Component
  • Automatic Hair Trimmer with Anti-Tangle Brush
  • Mop Holder
  • Mop
  • Base Ramp Extension Pad

3. Setup

3.1. Remove Protective Gear

Before first use, remove all protective covers from both sides of the robot vacuum.3.2. Install Brush and Mop Components

Install the edge brush and mop components into their designated positions until a 'click' sound is heard, indicating successful installation. The replaceable glue-fiber integrated main brush can be used.

3.3. Place the Universal Base

Place the all-in-one base against a wall on a hard, flat surface near a power outlet and in an area with good Wi-Fi signal (such as a floorboard or tile). Ensure a space with height greater than 0.82m, length greater than 1.93m, and width greater than 0.44m is reserved around the base.

3.4. Install Base Ramp Extension Pad

Install the base ramp extension pads on the universal base as shown in the diagram. After installation, the base ramp extension pad should be flush with the bottom of the universal base, with no protrusions.

3.5. Plug In

After properly installing the universal base, connect the electrical components and power it on. When powered on, the indicator light stays white. Excess power cords can be stored in the cable tray to prevent the main unit from dragging them, which might cause the all-in-one base to shift or lose power.

3.6. Host Charging

Before first use, long press the power button on the main unit for 3 seconds to power it on. After powering on, align the charging electrode of the host with the charging spring of the universal base. When the voice announcement confirms charging, the host has successfully connected to the universal base. It is recommended to fully charge the device before the first use. If the battery runs out and the device won't turn on, manually align and place the main unit on the universal charging dock for a while. If the host is charging, it will automatically start and cannot be turned off.

3.7. Fill the Water Tank

Fill the clear water tank to the highest water level. For better cleaning results, you can add an officially certified cleaner, such as "Daily Elements Floor Cleaner", which can be used after gently shaking to mix. Do not exceed the MAX water level when filling. Do not fill the tank with hot water, as it may cause deformation. Do not shake vigorously after adding the detergent. The "Daily Element Floor Cleaner" must be purchased separately from official channels, and should be mixed with water in a 1:100 ratio.

4. Operating Instructions

4.1. Connect to Mi Home App

This product is integrated with Mi Home, allowing control via the Mi Home app and seamless interoperability with other devices.

  1. Scan the QR code (if available in the original manual) to download and install the Mi Home app. Users who already have the Mi Home app installed will be directed to the device connection page. Alternatively, search for "Mi Home" in the app store and download and install the Mi Home app.
  2. Open the Mi Home app homepage, tap in the top-right corner, and add devices as prompted by the app.

Note: This product connects to the Mi Home app and is compatible with Android 9.0 or iOS 5.12.0 and later. It supports only Wi-Fi networks on the 2.4 GHz band. Due to updates to the Mi Home app, actual operations may differ slightly from the above description. Please follow the current app instructions.

4.2. Power On/Off

  • Press and hold the power button for 3 seconds to power on the device. The indicator light will illuminate, and the device will enter standby mode.
  • When the host is not charged and is temporarily off, hold the button for 3 seconds to power off.

Note: If the host is charging, it will automatically start and cannot be turned off.

4.3. Quick Map

After the first connection, the host will build the map quickly according to the APP instructions, but will not clean it. After the host automatically returns to the All-in-One Base, the map is created and saved automatically.

Important:

  • Ensure the robot's main unit has sufficient power and starts from the universal base.
  • Before mapping, clear loose items on the floor, open the room door, and block areas where the host cannot enter.
  • Do not follow, move, or interrupt the host while building the map. Do not move the universal base.
  • After creating the map, set up virtual walls or restricted zones in areas unsuitable for console access, such as Yikakun Gangteng. Also, set up virtual walls or restricted zones in areas with long-haired or fringed carpets to prevent console entanglement.
  • Before mopping, set up a virtual wall or restricted area in the carpet zone to prevent wetting the carpet.

4.4. Suspend

To pause the host during operation status check, press any key on the host briefly.

Note: During the Xiting period, avoid lifting or moving the host to prevent positioning errors that may cause the host to fail to recharge or lose its map.

4.5. Dormancy

If the pause exceeds 10 minutes, the host will automatically enter sleep mode, and the indicator light will turn off. Press any key on the host to wake it up.

Note: The host will shut down automatically if the sleep time exceeds 12 hours.

4.6. Continue Scan from Breakpoint

When the battery level is too low during cleaning, the host will automatically return to the All-in-One Base for charging. Once charged to the appropriate level, the host will resume cleaning from the last paused point.

4.7. Scan and Sync (Sweep-Drag Synchronization)

  1. Start Work: Ensure the host has installed components such as the mop assembly and the water tank is filled with water. In the app, select the scan-and-slip sync mode, then either use the app or press the power button on the host to initiate cleaning. The host will operate from the universal base, executing cleaning tasks based on the optimal cleaning plan generated by the built map.

Important: The host will dampen the mop before departure. Please wait patiently. Before starting, ensure the All-in-One Base is powered on and the host is connected to it. To ensure the host can return smoothly to the universal base after completing the sweeping and mopping operation, it is recommended to start from the universal base. During operation, avoid moving the universal base, water tank, sewage tank, or cleaning tray. You can enable the hot water mop function in the app. After enabling it, do not touch the mop outlet on the base to avoid burns.

4.8. Child Lock Settings

Long press the power button on the host for 3 seconds to turn the child lock on or off.

Note: When the child lock is enabled, the host buttons will not function. Use the app instead.

4.9. Dust Collection Function

Once the host completes the sweep-drag synchronization, first-sweep-and-drag mode, and dedicated sweeping tasks with automatic recharge, the All-in-One Base will automatically initiate dust collection.

Important:

  • When the host returns midway to clean the mop, the universal base will not automatically collect dust.
  • If the automatic dust collection feature is disabled in the app, the All-in-One Base will not automatically collect dust.
  • You can adjust the dust collection frequency in the app, and the universal base will clean dust at the set frequency.

4.10. Automatic Midwash

During the cleaning process, the host automatically returns to the universal base to clean the mop and replenish the water tank based on the cleaned area, then resumes the cleaning task.

4.11. Scan First, Then Drag (Mop)

  1. Ensure the host has installed components such as the mop assembly and the water tank is filled with water.
  2. In the app, select the "Scan First, Drag Later" mode. Then, either use the app or press the heart button on the host to initiate cleaning. The host will lift the mop assembly to start the cleaning process.

After cleaning, the All-in-One Base automatically collects dust and moistens the mop, then lowers the mop assembly to start mopping.

4.12. Just Sweep the Floor

In the app, select the floor-only mode, then use the app or press the button on the host to start cleaning. The host will lift the mop assembly and initiate cleaning from the universal base. After completing the cleaning task, it will return to the universal base. Dynamic dust collection.

4.13. Just Mop the Floor

  1. Ensure the host has installed components such as the mop assembly and the water tank is filled with water.
  2. In the app, select the floor-only mode and initiate cleaning either through the app or by pressing the power button on the host. The host will first automatically moisten the mop, then begin sweeping from the universal base.

After completing the floor-cleaning task, return to the universal base to clean and dry the mop.

4.14. Automatic Water Supply and Drainage System (Optional)

This product can be used with an automatic water supply and drainage system to achieve fully automatic water replacement. This device needs to be purchased separately. If you have purchased it, scan the QR code on its packaging to schedule a door-to-door installation service.

4.15. More APP Features

4.15.1. Map Function

The APP plugin home page displays the current scan-and-drag map. You can set the areas to avoid in the restricted area settings, and edit the current map in map management.

4.15.2. Clean and Cleaning Settings

In the cleaning settings, you can adjust the cleaning mode, suction level, and water flow for mopping based on the floor's dirtiness and your needs.

4.15.3. Base Setting

The base can be configured to perform dust collection and mop cleaning. In the dust collection settings, you can enable or disable the automatic dust collection feature, or adjust the dust collection frequency. Adjust the wash frequency in the mop settings.

Note: Complete the initial mapping when using the selection/district cleaning and map editing features. For more features, please refer to the APP. Specific details of each feature are subject to the APP.

4.16. Firmware Upgrade

The main card firmware can be upgraded via the Mi Home app. Before upgrading, ensure the host is on the All-in-One Base and has over 15% battery remaining.

4.17. Restart the Host

If the button is unresponsive or the device won't shut down, hold the power button for 15 seconds to force a shutdown, then press and hold it for 3 seconds to power on.

4.18. Factory Data Reset

If the host still cannot be used normally after restarting, press and hold the reset button for 3 seconds until the voice prompt starts restoring factory settings. The host will return to factory settings.

5. Maintenance and Care

To keep the host in good condition, regular maintenance is essential. Refer to the table below for daily maintenance frequency.

5.1. Component Maintenance Schedule

ComponentClean FrequencyChange Frequency
Sewage TankClean after each use-
Clear TankClean once every 2 weeks-
Cleaning TrayClean once every 1-2 weeks-
Hair and Bristle Integrated BrushClean once every 2 weeks6 months
Automatic Hair Trimmer with Anti-Tangle BrushClean once every 2 weeks6 months
Brush (Side Brush)Clean once every 2 weeks3-6 months
Dust BoxClean as needed-
Filter (installed in dust box)Clean once every 2 weeks3-6 months
Mop-1-3 months
Omni-directional Wheel--
Edge Sensor--
LDS Laser PickoffClean once a month-
Linear Laser Sensor--
Cliff Sensor--
Charging Electrode Sheet for Host--
Collision Buffer--
Host Dust Collection Port--
Automatic Water Supply Port of Host--
Bottom of the HostClean once a month-
All-in-One Base Unit--
Universal Base Dust Collection Port--
All-Purpose Base Charging Projectile--
All-Purpose Base Station Signal Transmitting Area--
Dust Bag-Approximately 2.5 months, subject to actual conditions

Note: The replacement frequency is for reference only. Replace damaged parts promptly to maintain cleaning effectiveness. To move or mail the product, empty both the wastewater and clean water tanks to prevent machine damage during transport.

5.2. Clean the Base Plate

  1. Turn on the self-cleaning function of the base in the APP. The host will automatically exit the all-in-one base.
  2. Remove the cleaning tray. The all-in-one base will automatically fill water into the base chassis, and clean the base chassis and cleaning tray with a cloth or brush.
  3. Wait 3 minutes for the universal base to automatically drain wastewater. Clean the base chassis and cleaning tray with a dry cloth, then reinsert the cleaning tray. After cleaning the base chassis, return it to the main unit.

Note: Do not tilt the universal base during daily use and cleaning. If water accumulates on the base, wipe it dry with a cloth.

5.3. Clean the Water Tank and the Sewage Tank

  1. Remove the clean water tank and the sewage tank separately. Open the upper blue cover, and drain the water inside.
  2. Rinse thoroughly with clean water and wipe off any remaining water stains on the exterior of the two water tanks, then reattach them to the universal base.

Note: The floats in the clear water tank and sewage tank are moving parts. Avoid excessive force during cleaning to prevent functional impairment.

5.4. Replace the Dust Bag

  1. After dust accumulation, pull the dust collection chamber cover outward from the handle, then grasp the dust bag handle to remove and discard it. Tip: Pull the handle of the dust bag to seal it, effectively preventing dust leakage.
  2. Wipe the dust and other dirt on the filter screen with a dry cloth.
  3. Install the new dust bag and slide the handle into the slot to secure it in place.
  4. Reassemble the dust collection bin cover until the 'click' sound is heard, ensuring it is properly installed.

5.5. Clean the Dust Box and Filter Screen

  1. Open the host cover, press and hold the dust box release button to remove the dust box.
  2. After opening the dust box cover, remove the filter screen, gently tap the filter frame to shake out the dirt, and empty the dust box.
  3. Rinse the dust box and filter screen with clean water. Do not add any detergent.
  4. Ensure the dust box and filter are completely dry before reinstallation.

Note: Do not clean the filter with brushes or fingers.

5.6. Clean and Coat the Main Brush

  1. Place the host upside down, press the release button on the main brush cover to remove it.
  2. Remove the integrated brush with the bristles, detach the side end caps, and clean the brush shaft.
  3. Cut the tangled hair with scissors and remove the debris.
  4. The main brush and the brush cover are installed and fastened together.

Note: Do not pull the bristles too hard when they are tightly entangled, as this may damage the integrated brush. The brush bristles can be removed for individual cleaning, but the main brush shaft is not water-washable.

5.7. Clean Automatic Hair Removal Brush with Anti-Tangle Design

  1. Remove the main brush cover and the automatic hair-cutting anti-entanglement brush.
  2. Pull off the detachable end cap.
  3. Remove the hair and clean it.
  4. Clean the gaps between the comb teeth with appropriate tools.
  5. After reinserting the hair strip and end cap, install the automatic hair-cutting anti-tangle main brush and its cover, then secure them firmly.

If the automatic hair cutting and anti-wrapping brush is seriously entangled with hair, check whether the dust box and dust bag are full, empty the dust box and replace the dust bag in time to ensure the normal function of the automatic dust collection.

5.8. Clean the Side Brush

  1. Flip the main unit, pull out the side brush, and clean it.
  2. Install the edge brush back into the host.

5.9. Clean the Swivel Wheels

  1. Flip the main unit and pull out the casters.
  2. Clean the hair and dirt on the wheel body and axle.
  3. Reinstall the swivel wheel and press it tight.

Note: If necessary, use a small screwdriver or similar tool to pry the axle off the caster for cleaning, but avoid excessive force. Rinse with tap water, dry thoroughly, and reinstall.

5.10. Change the Mop

Remove the mop from the mop stand and replace it.

5.11. Clean the Sensor, Charging Electrode, and Dust Collection Port

Clean the sensors, charging electrodes and dust collection ports on the main unit and universal base with a soft dry cloth.

5.12. Battery Maintenance

The host features a high-performance lithium-ion battery pack. To maintain battery performance, keep the host charged during daily use. If not used for an extended period, fully charge and store the device. Charge at least once every three months to prevent battery damage from over-discharge.

6. Troubleshooting

If you encounter any issues with your robot vacuum, refer to the table below for possible causes and resolutions.

Fault PhenomenonPossible ReasonsResolvent
Cannot bootThe main engine is underpowered.
The ambient temperature is either too high or too low.
Charge before use.
Use in an environment above 0°C and below 40°C.
Cannot chargeThe universal base is not powered or has poor contact.Check that both ends of the All-in-One Base Wire Assembly are properly connected.
Clean the charging debris from the universal base and the charging electrode of the main unit, then align and place them properly.
Failed to connectInvalid Wi-Fi password.
5GHz networks and enterprise routers are not supported.
The Wi-Fi signal is weak.
The host may not be in the pending connection state.
Enter the correct Wi-Fi password.
Switch to the 2.4 GHz network to connect.
Keep the host in an area with strong Wi-Fi signal.
Close the app, reset the host Wi-Fi, and reconnect to the network.
The host cannot find the All-in-One Base location, so it cannot return to the All-in-One Base.There are too many obstacles near the universal base.
The signal transmission area may be contaminated.
The universal base is not powered on.
The all-purpose base is moved when the host is external.
The recharging route is blocked, such as when the door is closed.
The host is out of place and cannot be located.
The All-Power Base is too far away to recharge.
Place the universal base in an open area.
Wipe the signal transmission area of the universal base to prevent dust or dirt accumulation.
Connect the All-in-One Base Power Supply.
Manually place the host back into the universal dock to charge.
The host is stuck in front of the All-in-One Base, preventing it from returning.There are too many obstacles near the universal base.
The recharging route is blocked, such as when the door is closed.
Slippery ground causes the main engine to slip.
The universal base is tilted or uneven.
Place the universal base in an open area.
Manually place the host back into the universal dock to charge.
We recommend manually cleaning the waterlogged floor.
Install the universal base and try again.
The host cannot be shut downDry charging state of host unitThe host must be unplugged before shutting down. Move the host away from the universal dock and hold the power button for 3 seconds to power off.
The device cannot be shut down after the previous step. Press and hold the power button for 15 seconds to force a shutdown. If the issue persists, contact customer service.
Cannot charge or charging is slowThe main engine power is too low.
The ambient temperature is either too high or too low.
The charging spring or charging electrode may be contaminated.
The main unit charges from low to full power in approximately 6.5 hours under normal conditions.
When operating in extreme temperatures, the device automatically reduces charging speed to extend battery life, which is a normal feature.
Wipe the charging spring and charging electrode with a dry cloth.
Brush bristles falling offThe brush is not installed properly.
Foreign body detachment caused by brush entanglement.
Reinstall the edge brush. You will hear a click sound indicating installation completion. Clean the floor of debris before use.
The mop has fallen off.The mop became entangled with a foreign object and subsequently detached.Remove debris from the floor before use.
The system is running at high volume during operationThe trash bin is full.
Foreign objects have entered the brush, main brush, or dust box.
The host suction level is high.
Clean the dust tray.
Check and confirm before cleaning.
The host suction setting can be adjusted to the standard or quiet mode.
Disorganized walking routes during workScattered ground objects affect the normal operation of the host.
Slippery ground causes the main engine to slip.
The linear laser sensor may be contaminated.
It is recommended to tidy up the floor before use.
We recommend manually cleaning the waterlogged floor.
Wipe the main unit's line laser sensor with a clean soft cloth to keep it clean and unobstructed.
Some rooms were not scanned.The cleaning path is obstructed, such as when the door is closed or the room threshold is higher than 2 cm. The room entrance is relatively slippery, causing the host to slip and malfunction.Ensure all doors are fully open. If this product cannot climb over high thresholds or steps, manually clear water from the floor.
The host frequently enters restricted areas or virtual wallsMap error.
The virtual wall or restricted zone boundary settings need optimization.
View the map in the app. If there is an exception, select the app's historical map or rebuild the map in the map list.
When setting up virtual walls or restricted areas, adjust the boundaries according to your home environment and include all areas prone to trapping (such as sunken steps, under furniture, etc.)
Scheduled cleaning does not workThe main engine is underpowered.The cleaning service will only activate when the battery level drops to 15%. Please charge your device promptly.
The host unexpectedly interrupted the current task during operationMain engine power exhausted.
The universal base is not powered on. The host cannot charge in the universal base.
Manually place the host back into the universal dock to charge.
Check if the power supply is properly connected.
If the issue persists, contact customer service.
The battery is low during cleaning. Charge again but do not continue scanning.The host is in Do Not Disturb mode.
The host is manually recharged (either by placing it back into the universal base or by initiating the task through the app or host buttons).
Do not disturb mode or manual recharging will not continue scanning.
The universal base indicator light is flashing orangeInsufficient water in the clear tank.
The empty or sewage tank is not installed, and the sewage tank is full.
Fill the water tank with water promptly.
Install the clean water tank and sewage tank in place.
Clean the sewage tank.
Misreport of water volume in the water tankThe float in the clear water tank is missing or stuck.Reset the float manually.
If the issue persists, contact customer service.
Abnormal water level in the base chassisThere may be blockage around the base and chassis.
The sewage tank is not properly installed.
The tank seal ring is loose.
Clean the base plate and the cleaning tray.
Reinstall the sewage tank.
Install the sewage tank seal properly.
If the issue persists, contact customer service.
Automatic dust collection without effortDust bag is full.
Dust collection port is blocked.
Replace the dust bag.
If the dust bag is not full, check and clean all dust collection ports.
The dust collection time has increased.After using the All-in-One Base for some time, the dust collection time may be extended to ensure stable operation, which is a normal phenomenon.-

7. Specifications

7.1. Main Engine Specifications

AttributeValue
Product NameSmart Vacuum Cleaner
ModelD103CN
SizeΦ350×97mm
Battery Capacity4800mAh (rated capacity), 5200mAh (nominal capacity) Li-ion
Charging IntervalAbout 6.5 hours
Net Weight of Host4.1kg
Support SystemAndroid 9.0 or iOS 12.0 and later
Wireless ConnectionsWi-Fi IEEE 802.11b/g/n 2.4GHz, Bluetooth 4.2
Rated Voltage14.4V
Charging Voltage20V
Power Rating80W
FunctionMopping & Sweeping & Suction Type
Dust Box Capacity (L)0.6-1 L
Liquid Tank Volume>3L
Dust Storage TypeCyclone Dust Bucket
Cleaning RoutePlanned Type
Number of Operating Modes3-4
Cord Length (m)Wireless
Timing ReservationYes
Remote ControlYes
InstallationRobot
CertificationCE
OriginMainland China
Weight>10 kg
High-concerned chemicalNone

7.2. Universal Base Specifications

AttributeValue
ModelJZ2401
Size457×340×588mm
Rated Input220V~50Hz
Rated Output20V-1A
Power (Dust Collection State)1000W
Power (Hot Water Cleaning Mode)1040W
Power (Drying + Charging State)76W

Note: The power (hot water cleaning mode) is determined by the typical period power value (with water temperature at 15°C). The power (drying and charging states) is determined by the full-load power value.

7.3. Package Dimensions and Weight

AttributeValue
Length44 cm
Width41 cm
Height67 cm
Weight15.6 kg

8. Warranty and Support

The M30S Mi Home all-in-one sweeping and mopping robot provides a three-guarantee service (repair, replacement, and refund) strictly compliant with China's Consumer Rights Protection Law and Product Quality Law.

8.1. Warranty Period

  1. Within 7 days after you sign for the product, if the product has the performance failure listed in the Mi Home All-in-One Robot M30S Product Performance Failure Table, you can enjoy free return or exchange service after the Xiaomi after-sales service center checks and confirms.
  2. Within 8 to 15 days after you sign for the product, if the product has performance faults listed in the Mi Home All-in-One M30S Product Performance Fault Table, you can enjoy free replacement or maintenance service after the Xiaomi after-sales service center checks and confirms.
  3. If any performance issues specified in the 'Mijia All-in-One Mopping & Sweeping Robot M30S Product Performance Fault List' occur within 24 months from the day after your receipt, the product will be repaired free of charge upon verification by Xiaomi's After-sales Service Center.

8.2. Warranty Coverage

TypeWarranty ContentWarranty Period
Main EngineHost (excluding consumables), universal base2 years
AppendixWire assembly2 years
Quick-wear PartCell1 year

Note: The main brush cover, integrated bristle brush, automatic hair-cutting anti-tangle brush, filter screen, edge brush, mop, and dust bag are consumables included with the product and are not covered by the warranty.

8.3. Non-Warranty Regulations

  1. Unauthorized repair, misuse, collision, negligence, abuse, liquid intrusion, accident, modification, incorrect use of non-Tai product accessories, or tearing or altering labels and anti-counterfeiting marks.
  2. The warranty period has expired.
  3. Damage caused by force majeure.
  4. The product fails to meet the performance criteria specified in the 'Mijia All-in-One Mopping & Sweeping Robot M30S Product Performance Failure Table'.
  5. This product and its accessories may develop performance failures as listed in the 'Mijia All-in-One Mopping & Sweeping Robot M30S Product Performance Failure Table' due to human factors.

8.4. Support Information

9. User Tips

  • Region Setting: For optimal functionality and to ensure the robot works correctly, some users have found it helpful to select the region as 'Mainland China' in the Mi Home app settings during initial setup.
  • Dual Functionality: This device is an all-in-one robot that performs both vacuuming (sweeping and suction) and floor mopping.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.