Solar Power PWM Solar Charge Regulator Controller

Contents

PWM Solar Charge Regulator Controller User Manual

Models: 10A, 30A, 50A, 100A

1. Introduction

Thank you for choosing the Solar Power PWM Solar Charge Regulator Controller. This device is designed to manage the power flow from your solar panel to your battery and DC load, ensuring efficient charging and protecting your battery from overcharge and over-discharge. It features a clear LED display, dual USB ports for charging devices, and a built-in timer function for load control.

PWM Solar Charge Controller with LED screen and dual USB ports

Image 1: Front view of the PWM Solar Charge Controller highlighting its LED screen, dual USB, and protection features.

2. Key Features

  • PWM Charging: Efficiently charges your battery using Pulse Width Modulation technology.
  • LED Display: Provides real-time display of system status, including battery voltage, charging status, and load status.
  • Dual USB Ports: Conveniently charge mobile phones, tablets, and other USB-powered devices (5V output).
  • Built-in Timer: Programmable timer function for controlling the DC load.
  • Multiple Protection Functions:
    • Overcurrent protection
    • Reverse connection protection
    • Short circuit protection
    • Overcharge protection
    • Overdischarge protection
  • MCU Control: Microcontroller unit for intelligent management.
  • Settable Voltage: Adjustable charge and discharge parameters.
Solar Controller with LCD and dual USB, listing features

Image 2: Solar Controller highlighting its LCD, dual USB, and various current ratings (10A-100A).

3. Safety Precautions

  • Ensure proper ventilation around the controller.
  • Connect the controller to the battery first, then the solar panel, and finally the load. Disconnect in reverse order.
  • Use appropriate wire gauges for your system's current to prevent overheating.
  • Do not expose the controller to water or excessive humidity.
  • Ensure all connections are tight and secure to prevent loose contacts and sparks.
  • This controller is designed for lead-acid batteries (OPEN, AGM, GEL). Do not use it with other battery types unless specified.

4. Installation and Wiring

4.1 Mounting

Mount the controller vertically on a wall or panel in a well-ventilated area, away from direct sunlight, high temperatures, and water. Ensure there is sufficient space around the controller for air circulation.

4.2 Wiring Diagram and Connection Order

Follow the wiring diagram carefully. Incorrect wiring can damage the controller and other components. Always connect in the following order:

  1. Connect the Battery: Connect the battery to the controller's battery terminals (marked with a battery symbol). Ensure correct polarity (+ to + and - to -).
  2. Connect the Solar Panel: Connect the solar panel to the controller's solar panel terminals (marked with a solar panel symbol). Ensure correct polarity.
  3. Connect the DC Load: Connect the DC load to the controller's load terminals (marked with a light bulb symbol). Ensure correct polarity.
Wiring diagram for solar charge controller with dimensions

Image 3: Wiring diagram showing connections for solar panel, battery, and load. Dimensions are approximately 133.5mm (width) x 70mm (height).

Note: To disconnect the system, reverse the order: first disconnect the load, then the solar panel, and finally the battery.

5. Operating Instructions

5.1 Display Interface

The LED display shows various parameters. Use the buttons to navigate through the display modes and adjust settings.

5.2 Button Functions

  • MENU Button: Short press to cycle through display modes (e.g., battery voltage, charging current, load status). Long press to enter parameter setting mode.
  • UP Button: In setting mode, increases the value of the selected parameter.
  • DOWN Button: In setting mode, decreases the value of the selected parameter.

5.3 Parameter Settings

To enter parameter setting mode, long press the MENU button. Use UP/DOWN buttons to adjust values and short press MENU to confirm and move to the next parameter. Long press MENU again to exit setting mode.

Commonly Adjustable Parameters
ParameterDescriptionTypical Range
Battery TypeSelect battery type (B01=OPEN, B02=GEL, B03=AGM)B01, B02, B03
Charge VoltageOvercharge protection voltage13.0V - 15.0V (for 12V system)
Discharge ReconnectVoltage at which load reconnects after low voltage disconnect11.0V - 13.0V (for 12V system)
Discharge Cut-offLow voltage disconnect voltage9.0V - 11.0V (for 12V system)
Load ModeLoad control mode (e.g., 24H=always on, 0-23H=timer)0-24

5.4 USB Output

The dual USB ports provide a 5V output for charging compatible devices. These ports are active when the controller is powered.

6. Maintenance

  • Periodically check all wire connections to ensure they are tight and free from corrosion.
  • Keep the controller clean and free from dust and debris. Use a dry cloth for cleaning.
  • Ensure proper ventilation is maintained around the controller.

7. Troubleshooting

Common Issues and Solutions
ProblemPossible CauseSolution
Controller display is offNo power from battery or reverse polarityCheck battery connections and polarity. Ensure battery voltage is above minimum operating voltage.
Battery not chargingSolar panel not connected, low sunlight, or reverse polarityCheck solar panel connections and polarity. Ensure sufficient sunlight. Check for open circuit in solar panel wiring.
Load not workingLoad disconnected, low battery voltage, or load mode settingCheck load connections. Charge battery. Adjust load mode settings (e.g., timer).
USB ports not workingController not powered or device incompatibleEnsure controller is powered. Check if the device requires more current than USB can provide.

8. Specifications

Technical Specifications
ParameterValue
System Voltage12V/24V Auto-detect
Max. Charge/Discharge Current10A, 30A, 50A, 100A (model dependent)
Max. Solar Input Voltage<50V
USB OutputDual USB, 5V/2A (Max)
Standby Current<10mA
Operating Temperature-35°C to +60°C
Dimensions (approx.)133.5mm x 70mm (Width x Height)
ProtectionOvercurrent, Reverse Polarity, Short Circuit, Overcharge, Overdischarge

9. Warranty and Support

For any issues not covered in this manual, please contact your retailer or seller for support. Keep your purchase receipt for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.