RACBOX Passenger Armrest Trim LED Light

Contents

RACBOX Motorcycle LED Passenger Armrest Light

User Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your RACBOX Motorcycle LED Passenger Armrest Trim Lights. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Safety & Warnings

Important Safety Information:

  • Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
  • Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.

3. Product Information

The RACBOX Motorcycle LED Passenger Armrest Trim Light is designed as an auxiliary accessory for motorcycle lighting, specifically for turn signal functionality. It is intended for normal replacement and upgrade of original lights.

Product Overview:

RACBOX Motorcycle LED Passenger Armrest Lights, showing both red and smoked lens versions.

Image: RACBOX Motorcycle LED Passenger Armrest Lights, showing both red and smoked lens versions.

Package Contents:

Package contents including two LED lights and wiring accessories.

Image: Package contents including two LED lights and wiring accessories.

  • 1 Pair Passenger Armrest Trim LED Lights
  • Required wiring and connectors

4. Setup & Installation

Please ensure your motorcycle is compatible with this product before beginning installation. This product is compatible with Honda 2006-2017 Goldwing GL1800 models. It will NOT fit F6B Models.

Installation Steps:

  1. Power Off First: Turn off the motorcycle's power switch and unplug the negative terminal of the battery to prevent any short circuits during installation.
  2. Dismantling Old Lights: Carefully remove the original turn signal lights from the passenger armrest area. Disconnect or cut the corresponding wiring harness.
  3. Install New Lights: Align the fixed bracket of the new LED lights with the original mounting holes on your motorcycle. Securely tighten the turn signal screws.
  4. Wiring: Connect the wires of the new LED lights to the motorcycle's wiring harness. Ensure that wires of the same color are connected. Proper insulation and waterproofing of all connections are crucial. LED lights may require dedicated flashers for correct operation.
  5. Wiring diagram for the LED lights showing negative, red low brightness, and red high brightness connections.

    Image: Wiring diagram for the LED lights. Connect the black wire to Negative, blue wire to Red Low Brightness, and red wire to Red High Brightness.

  6. Testing Function: Reconnect the battery. Test both the left and right turn signals to confirm they flash normally.
  7. Comparison of low and high brightness modes of the LED light.

    Image: Comparison of low and high brightness modes of the LED light.

  8. Reinstall Casing: Once functionality is confirmed, carefully reinstall any removed casings or covers.

Note:

  • If the light does not turn on during testing, please reverse the plug polarity.
  • Requires bike-specific rear accessory harness for plug-n-play installation.

Installation Location:

Images showing the installation location on a Honda Goldwing GL1800 (passenger armrest area).

Image: Visual guide to the installation location on a Honda Goldwing GL1800 passenger armrest.

5. Operating Instructions

These LED lights function as turn signals and operate in conjunction with your motorcycle's existing turn signal switch. Once properly installed, activate your motorcycle's turn signal lever as you normally would to engage the lights.

6. Maintenance

  • Cleaning: Use a soft, damp cloth to clean the light lenses. Avoid abrasive cleaners that could scratch the surface.
  • Inspection: Periodically check the wiring connections to ensure they are secure and free from corrosion.
  • Damage: If any part of the light housing or wiring appears damaged, it is recommended to replace the unit to ensure safety and proper function.

7. Troubleshooting

  • Light Does Not Turn On:
    • Check all wiring connections for proper contact.
    • Ensure the plug polarity is correct; if not, reverse it.
    • Verify the motorcycle's turn signal system is functioning correctly.
  • Lights Flicker or Are Dim:
    • Check for loose or corroded wiring connections.
    • Ensure proper voltage supply from the motorcycle's electrical system.
  • Improper Flashing Speed:
    • LED lights may require a load equalizer or an LED-compatible flasher relay to correct hyper-flashing or no-flashing issues.

8. Specifications

BrandRACBOX
Item TypeTurn Signal Light
Model NamePassenger Armrest Trim LED Light
MaterialABS
Light ColorRed
FitmentCompatible with Honda 2006-2017 Goldwing GL1800 (NOT F6B Models)
Length240mm
Height65mm
Wire Length720mm
Battery IncludedNo
High-concerned chemicalNone
OriginMainland China
Package Weight0.34 kg
Package Dimensions26cm x 10cm x 7cm
Product dimensions diagram showing length 240mm, height 65mm, and wire length 720mm.

Image: Product dimensions diagram showing length 240mm, height 65mm, and wire length 720mm.

9. Warranty & Support

RACBOX Warranty Information:

RACBOX Warranty details: Standard Warranty and Warranty Period.

Image: RACBOX Warranty details: Standard Warranty and Warranty Period.

  • Standard Warranty: RACBOX represents and warrants to the end-user that the Product shall materially conform to RACBOX's published specifications in the user manual, subject to the terms and conditions below.
  • Warranty Period: One Year (12 Months) from the date a new product is first delivered to the End-User after being purchased.
RACBOX Warranty details: What is Covered, What is NOT Covered, How to Get Warranty Service.

Image: RACBOX Warranty details: What is Covered, What is NOT Covered, How to Get Warranty Service.

  • What is Covered: The Standard Warranty provides support from Racbox, as well as replacement parts and shipping costs during the Warranty Period. Customers will be covered for replacements, partial refunds, or full refunds in the Warranty Period on any product due to manufacturing defects of components or workmanship.
  • What is NOT Covered: The Warranty does not cover any damage due to abuse, wrong installation, neglect or misuse, extreme environment, unusual physical or electrical stress or interference, exposure to flooding, fire, or electrical problems associated with incoming power or other acts not the fault of Racbox. The Warranty does not cover accessory parts. Racbox is not responsible for damage arising from end-user error and failure to follow instructions relating to Product's use.
  • How to Get Warranty Service: If you have any questions or need to request a replacement part, please contact RACBOX customer support either by phone, email, or through their Live Support system.

© 2024 RACBOX. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.