Angel Wings LED Projector Angel Wings LED Projector

Contents

Motorcycle Angel Wings LED Welcome Light

LED Underbody Light Projector Decorative Atmosphere Light Accessories

Model: Angel Wings LED Projector

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your new Motorcycle Angel Wings LED Welcome Light. Designed to enhance the aesthetic appeal of your motorcycle, this LED projector creates a unique 'angel wings' light effect on the ground, serving as both a decorative element and a welcome light. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Safety Information

  • Always ensure the motorcycle's power is off before attempting any installation or wiring.
  • Incorrect wiring can cause damage to the product or your motorcycle's electrical system. If unsure, consult a professional.
  • Do not look directly into the LED light source when it is active, as it may cause eye strain.
  • Ensure the lights are securely mounted and do not obstruct any moving parts or critical components of the motorcycle.
  • Keep the product away from extreme heat, moisture, and corrosive substances.
  • This product is designed for decorative purposes and should not replace essential motorcycle lighting.

Package Contents

Verify that all items are present in your package:

  • 2 x LED Projection Lamps
  • 1 x Controller Unit
  • 2 x 3M Adhesive Pads
  • 4 x Mounting Screws
Product box and components including two LED projection lamps, a controller, adhesive pads, and screws.
Image: Contents of the Angel Wings LED Welcome Light package.

Specifications

Feature Specification
Product Type LED Underbody Light Projector / Welcome Light
Power Source Motorcycle Electrical System
Battery Included No
High-concerned chemical None
Origin Mainland China
Package Dimensions (approx.) 22cm (L) x 12cm (W) x 5cm (H)
Package Weight (approx.) 0.107 kg

Setup and Installation

Follow these steps to install your Angel Wings LED Welcome Light:

  1. Choose Mounting Location: Select a flat, clean surface on the underside of your motorcycle where the projection lamps can cast the 'angel wings' effect without obstruction. Ensure the location is protected from direct impact and excessive heat.
  2. Prepare Surface: Clean the chosen mounting area thoroughly to remove any dirt, grease, or debris. Allow it to dry completely.
  3. Mount Projection Lamps:
    • Attach the two 3M adhesive pads to the back of each projection lamp.
    • Carefully position and press the projection lamps onto the prepared surfaces.
    • For added security, use the provided screws to firmly attach the lamps to the motorcycle chassis.
  4. Connect Wiring: Refer to the wiring diagram below.
    • Connect the terminal heads of the two projection lamps to the corresponding connectors on the controller unit.
    • Identify the positive (+) and negative (-) wires from the controller.
    • Connect the positive (+) wire from the controller to a suitable 12V power source on your motorcycle (e.g., ignition switch, parking light circuit) that activates when the motorcycle is on.
    • Connect the negative (-) wire from the controller to a reliable ground point on the motorcycle chassis.
  5. Secure Controller: Find a safe, dry location to mount the controller unit, away from moving parts and excessive heat. Use additional adhesive or zip ties if necessary.
  6. Test Functionality: Once all connections are secure, turn on your motorcycle's power to test the lights. Ensure the 'angel wings' projection is clear and visible on the ground.
Wiring diagram showing two projection lamps connecting to a controller, with positive and negative electrodes for power connection, and adhesive pads and screws for mounting.
Image: Detailed wiring diagram for the Angel Wings LED Welcome Light.

For a visual guide on the product's appearance and effect, please watch the demonstration video:

Video: Demonstration of the Angel Wings LED Welcome Light in action on a motorcycle.

Operating Instructions

The Angel Wings LED Welcome Light is designed for simple operation:

  • Once properly installed and wired to an appropriate power source (e.g., ignition or parking light circuit), the lights will automatically activate when your motorcycle's power is turned on.
  • The lights will project the 'angel wings' pattern onto the ground, providing a decorative and welcoming effect.
  • To turn off the lights, simply turn off your motorcycle's power.

Maintenance

  • Cleaning: Periodically clean the lens of the projection lamps with a soft, damp cloth to ensure clear projection. Avoid abrasive cleaners.
  • Inspection: Regularly check the wiring connections for any signs of wear, corrosion, or looseness. Ensure the mounting screws and adhesive pads are still secure.
  • Protection: While designed for outdoor use, prolonged exposure to extreme weather conditions (heavy rain, snow, direct sunlight) may affect the product's lifespan.

Troubleshooting

Problem Possible Cause Solution
Lights do not turn on. No power, loose connection, incorrect wiring, faulty LED. Check all wiring connections (positive, negative, lamp terminals). Ensure the motorcycle's power is on. Verify the power source is active.
Projection is dim or unclear. Dirty lens, obstructed projection path, weak power. Clean the lens of the projection lamps. Ensure nothing is blocking the light path. Check power supply voltage.
Lights flicker. Loose wiring connection, unstable power supply. Inspect all wiring for loose connections. Ensure a stable 12V power supply.

User Tips

  • Consider wiring the lights to a separate switch for manual control, allowing you to turn them on/off independently of the motorcycle's ignition.
  • For optimal visibility of the projection, install the lights in a location that minimizes interference from other light sources.
  • Before permanent installation, temporarily connect the lights and test different mounting angles and positions to achieve the desired 'angel wings' effect.

Additional Resources

For further details and potentially more comprehensive instructions, you may refer to the official user manual PDF available here.

Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims or technical support, please contact the seller or retailer from whom you purchased the product. Keep your proof of purchase for warranty validation.

© 2023 Generic Motorcycle Accessories. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.