Introduction
Dear users: In order to enable you to use this product correctly, please read this manual carefully before use.
Product Features
- Lightweight in size, light in weight, high in efficiency, low in working noise, and reasonable in design.
- Adopting efficient SPWM Pulse Width Control Technology.
- Adopting multiple high-tech and intelligent driver chips.
- SMT Chip Mounting Technology, precise control, high reliability, and low failure rate.
- High efficiency conversion rate, strong load capacity, and wide application range.
- Multiple intelligent security protection with complete protection functions.
Main Components
The inverter features a clear layout for easy operation and monitoring.
- Indicator Light: Green for normal operation, Red for protection status.
- Universal Shaped Socket: For AC output.
- Independent Switch: Power ON/OFF control.
- Input Terminal Positive Terminal (Red): For positive DC input connection.
- Input Negative Terminal (Black): For negative DC input connection.
- Efficient Cooling Fan: For temperature control and heat dissipation.
Setup and Connection
How to Connect to Battery
Attention: When directly connected to the battery for use, the general car battery is 12V. It is necessary to choose a battery with the same input voltage as the power inverter for use, and multiple batteries can be used in parallel.
Connection Method for Car Cigarette Lighters
Attention:
- Choose a power inverter equipped with a car-mounted cigarette lighter model to use this method.
- The cigarette lighter output can only carry electrical appliances with a load of less than 150W. If it exceeds 150W, please follow the direct battery connection method.
Connection Method of Electric Motorcycle
Attention: Generally, the voltage of four batteries of an electric motorcycle is 48V, and that of five batteries is 60V. The specific voltage shall be subject to the voltage marked on the electric motorcycle, and then the inverter with the same voltage as the electric vehicle shall be selected for use.
Operating Instructions
- Place the inverter switch in the OFF position, then connect the inverter to the battery and ensure good contact.
- Confirm that the power of all electrical appliances is within the rated power range (50% of the peak power marked by the inverter), and that the peak power of inductive load electrical appliances does not exceed the peak power marked by the inverter. Then, plug the electrical plug into the 110V output socket of the inverter.
- Turn on the switch of the power inverter, and the green indicator light is on, indicating normal operation.
- The red indicator light on indicates that the inverter is turned off due to overvoltage, undervoltage, overload, and overheating.
- In many cases, due to the limited output of the vehicle cigarette lighter socket, the normal inverter alarms or shuts down. In this case, as long as the vehicle is started or the power consumption is reduced, normal operation can be restored.
Requirements for the Usage Environment
Based on safety and performance considerations, the installation environment should meet the following conditions:
- Dry: Do not immerse in water or rain.
- Temperature Conditions: A cool place with a temperature between 0°C and 40°C.
- Space Conditions: Do not use the power inverter in a narrow space, do not cover the machine for use, and pay attention to good ventilation!
Matters Needing Attention
- When the refrigerator compressor, motor, and other appliances reach their peak power during startup, although the inverter can withstand the nominal peak power, the peak power of some appliances that meet the requirements may exceed the peak output rate of the inverter, causing overload protection, output being turned off, and driving multiple appliances simultaneously. This situation may occur. Therefore, at this time, the electrical switch should be turned off first, the inverter switch should be turned on, and then the electrical switches should be turned on one by one, and the highest peak electrical appliance should be turned on first.
- During use, the battery voltage begins to decrease. Taking a 12V battery as an example, if the voltage at the DC input end of the inverter drops to 10.4-11.0V, the alarm will sound a buzzing sound. At this time, the computer or other sensitive electrical appliances should be turned off in a timely manner and the alarm sound should be ignored. The inverter will stop outputting current when the voltage drops to 9.7-10.3V, and the red indicator light will light up.
- The vehicle should be started or the battery should be charged in a timely manner to prevent battery depletion from affecting the start and battery life of the vehicle.
- Although the power inverter design has the ability to protect against overvoltage, taking a 12V battery as an example, it is still possible to damage the power inverter when the input voltage exceeds 16V.
- After continuous use of the power inverter, the surface temperature of the machine casing will rise to 60°C. It is necessary to ensure smooth airflow and keep away from objects susceptible to high temperature noise.
- This power inverter is prohibited for use by minors!
Safety Protection Functions
Main Technical Parameters
| Parameter | Value |
|---|---|
| Rated Power | 1000W - 6000W (model dependent) |
| Input Voltage (DC) | 10-15V / 22-30V / 40-60V / 60-80V (model dependent) |
| Output Voltage (AC) | AC 220V±10% |
| Output Frequency | 50Hz / 60Hz |
| Current Waveform | Corrected Sine Wave or Pure Sine Wave |
| Conversion Efficiency | >90% (0.9) |
| No-load Current | <0.3A |
| Built-in Fuse | 10A / 15A / 20A / 40A / 70A / 120A / 240A (model dependent) |
| Under Voltage Alarm | 10.4-11.0V / 20.5-22V / 42-45V / 54-57V |
| Low Pressure Shutdown | 9.7-10.3V / 19.4-20.6V / 39-42V / 48-52V |
| Overpressure Shutdown | 14.5-15.5V / 29-31V / 58-62V / 74-80V |
| Socket Type | Universal |
| Certification | CE |
| High-concerned chemical | None |
| Voltage (Safety/Category) | 50V AC / 75V DC and above |
Common Problems & Solutions
| Abnormal Phenomenon | Reason | Resolution Method |
|---|---|---|
| Indicator Light Is Not On, Electrical Appliance Is Not Working | Cause of malfunction by battery | Check if output voltage of battery is consistent with voltage marked on machine, and replace if necessary. |
| Reverse connection of positive and negative poles | Check battery connection. The power inverter may be damaged and need replacement or return for warranty. | |
| Poor contact at the wiring | Check connecting wires and connections, and tighten the wiring terminals. | |
| Indicator Light Is Red, Electrical Appliance Is Not Working | Power of electrical appliance exceeds continuous power of inverter, causing overload shutdown | Use electrical appliances with power lower than the continuous power of the power inverter. |
| Power of electrical appliance is less than continuous power, but peak power is too high | The peak power of electrical appliances used should be within the peak power range of the power inverter. | |
| Battery discharged (alarm) | Charge or replace the battery. | |
| Poor ventilation, causing overheating shutdown | Turn off machine, cool down for 15 minutes, remove items around fan and converter, place inverter in cool place, reduce use of electrical appliances as required, and restart. | |
| Input voltage too high | Check the working status of the charging system. | |
| Detected Output Voltage of Inverter Is Too Low | Measured output voltage of voltmeter is too low | Output data of the correction wave inverter should be measured using a "True RMS Multimeter" to obtain accurate data. |
| Power Inverter Emits A Buzzing Alarm Sound | Undervoltage or over temperature protection | Shorten or use thicker wires to connect the battery, lower the temperature of the machine, improve ventilation conditions around the machine, place the machine in a cool place, and reduce the use of electrical appliances as required. |
| Power Inverter Can Only Be Used For Low-power Appliances | When current passes through a wire, the voltage decays | Reduce the length of the wire and use thicker wires. |
| Electrical power consumption is greater than the rated power of the power inverter | Using a larger capacity battery. | |
| Battery Usage Time Is Too Short | Poor or damaged battery health | Replacing the battery. |
| Electricity stored after being fully charged is still insufficient | The charger cannot fully charge the appliance, replace it with a better intelligent charger. | |
| Current decays as it passes through a wire | Reduce the length of the wire and use thicker wires. |
User Tips
- Actual Power Output: Be aware that the actual continuous power output may be lower than the advertised peak power. For example, a 3000W inverter might deliver around 1200W-1500W continuously before protection modes activate. Plan your load accordingly.
- Overheat Protection: The inverter may enter overheat protection mode with sustained high loads (e.g., over 2kW for a 4kW model). Ensure adequate ventilation and avoid covering the unit to prevent premature shutdowns.
- Input Voltage Compatibility: Always verify that the input voltage of your inverter (e.g., 48V, 72V) precisely matches your battery system's voltage to prevent damage and ensure proper operation.
- Battery Capacity: For optimal performance, especially with higher wattage models or prolonged use, ensure your battery system has sufficient Amp-hour (Ah) capacity to support the intended load.
Warranty & Support
Warranty Terms
In order to ensure the after-sales service of the product is intact and better, customers must strictly follow the instructions when receiving the product. This product has a three-year warranty!
- Product Exchange Application: The accessories must be complete and not affect secondary sales. (Missing relevant accessories will be deducted based on the factory price).
- Product Warranty Application: If the machine encounters quality problems without opening or modifying the original packaging, it will be repaired, replaced, or sent back to the manufacturer for free repair, no charge for repair. If the product encounters quality problems due to unauthorized opening or modification, it will be paid maintenance.
- If the machine casing is too dirty or old and used in harsh environments, resulting in product damage, it will be paid maintenance.
- For high-power machine casings that are severely scratched, dirty or old, they should be returned to the factory for repair. After being repaired within the warranty period, the machine will be returned to the customer in its original condition and will be repaired for free. For machines that have been modified or unpacked without permission, any malfunctions will be paid maintenance. Please contact customer service for specific costs.
- After receiving the relevant fees, we will promptly handle the after-sales service and deliver the product to the customer by express delivery.
Return and Exchange Registration
Please contact customer service to obtain the return address and phone number for returns and exchanges. A detailed Return and Exchange Registration Form is available in the full user manual.
For a complete and detailed manual, including the Return and Exchange Registration Form, please refer to the official PDF document: CHANTOWER Power Inverter User Manual (PDF).