BMW BMW Welcome Light Projector

Contents

BMW LED Car Door Logo Projector Lamps User Manual

Model: BMW Welcome Light Projector

1. Product Overview

The BMW LED Car Door Logo Projector Lamps are designed to enhance your vehicle's ambiance by projecting a clear, high-definition BMW logo onto the ground when the car door is opened. These welcome lights are a direct replacement for your original door lights, offering easy installation and a durable design.

BMW Projection Welcome Light with various BMW logos and the LED projector unit.

This image displays the LED projector unit alongside several BMW logo designs, highlighting the 'HD projection' and 'refuse to fade' features.

2. Safety & Warnings

  • ATTENTION: Not suitable for children under 36 months.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.
  • Ensure the vehicle's power is off before attempting installation to prevent electrical hazards.

3. Setup and Installation

Before first use, remove all protective films from the product lenses. This product is designed for direct installation as a replacement for your existing door lights.

Installation Steps:

  1. Remove Original Door Lights: Use appropriate tools (e.g., a plastic pry tool or screwdriver) to carefully remove the original door light assembly from its housing.
  2. Disconnect Wiring: Disconnect the electrical connector from the original door light.
  3. Connect New Projector Light: Connect the wiring harness of the new LED projector lamp to the vehicle's door power supply connector. Ensure a secure connection.
  4. Insert New Projector Light: Carefully insert the new LED projector lamp into the door light housing.
  5. Secure in Place: Push the projector light firmly until it clicks into place, ensuring it is flush with the door panel.
  6. Test Functionality: Open the car door to verify that the logo projects clearly onto the ground.
Four-step diagram showing easy installation of the car door welcome light.

Step-by-step guide for installation: 1. Remove original light. 2. Connect new light to power. 3. Insert new light. 4. Secure new light.

4. Operating Instructions

Once installed, the BMW LED Car Door Logo Projector Lamps operate automatically. When you open your car door, the integrated sensor will activate the projector, displaying the high-definition BMW logo onto the ground. The light will turn off automatically when the door is closed.

BMW car with doors open, showing projected M Performance and BMW roundel logos on the ground.

An installed welcome light projecting the 'M Performance' and BMW roundel logos onto the ground from an open car door.

5. Maintenance

These projector lamps are designed for durability and minimal maintenance. The ABS resin shell provides fast heat dissipation and high temperature resistance, while the 4-layer HD lens ensures clear and bright projection that resists fading over time.

  • Cleaning: If the projection appears dim or unclear, gently wipe the lens with a soft, dry, lint-free cloth. Avoid using abrasive cleaners or solvents.
  • Inspection: Periodically check the projector for any physical damage or loose connections.
Detailed view of the LED projector lamp showing ABS resin shell and HD 4-layer lens components.

Close-up of the projector lamp highlighting its ABS resin shell for heat dissipation and a 4-layer HD lens for clear projection.

6. Troubleshooting

Common Issues and Solutions:

  • No Projection / Light Not Turning On:
    • Check the electrical connection to ensure it is secure and properly seated.
    • Verify that the car door is fully open to trigger the light.
  • Unclear or Blurred Projection:
    • Gently clean the projector lens with a soft, dry cloth to remove any dust or smudges.
    • Ensure the projector unit is correctly installed and fully seated in its housing.
    • This product uses imported nano glass lenses and 10x HD patterns to prevent common issues like blurring and fading often seen in inferior products. If issues persist after cleaning, contact support.
Comparison image showing a clear BMW logo projection from 'My products' versus an unclear, blurred projection from 'Products on the market'.

Visual comparison demonstrating the superior clarity of the product's projection (real shot display, imported nano glass lenses, 10x HD patterns) against inferior market products (blurred, prone to fever, unclear).

7. Specifications

FeatureDetail
Product TypeLED Car Door Logo Projector Lamps / Welcome Light
CompatibilityFor BMW E90, E91, E92, E93, E60, E61, F10, F07, E63, E64, F12, F13, F30, E87, F20 (Please verify with your specific model and year)
Sticker PlacementDoor Interior
Item Diameter6 cm
Shell MaterialABS Resin (Fast heat dissipation, high temperature resistance)
Lens TypeHD Lens (4 layers, imported nano glass)
Package DimensionsLength: 18 cm, Width: 15 cm, Height: 5 cm
Package Weight0.12 kg
High-Concerned ChemicalNone
OriginManufactured in China

8. User Tips

  • Compatibility Check: Always verify compatibility with your specific BMW model and year before purchasing and installing. Refer to the specifications section for a list of compatible models.
  • Gentle Installation: Use non-marring tools (e.g., plastic pry tools) when removing original lights to avoid damaging your car's interior trim.
  • Lens Care: For the clearest projection, keep the projector lens clean and free of dust or fingerprints.

9. Frequently Asked Questions (FAQ)

Q: Is this product compatible with my BMW [specific model, e.g., F36, X3 2026, F25, F23]?

A: Please refer to the detailed compatibility list provided in the 'Specifications' section of this manual. If your specific model is not listed, or if you are unsure, it is recommended to consult your vehicle's manual or contact the seller for confirmation before purchase.

10. Warranty & Support

For any product-related inquiries, technical support, or warranty claims, please contact the manufacturer or their authorized representative:

  • Manufacturer: Guangzhou Rongjiao Business Service Co., Ltd.
  • Manufacturer Email: bb65356802@163.com
  • EU Authorized Representative: JXGO SARL
  • EU Representative Address: 79 rue de Patay 75013 Paris, FR (France)
  • EU Representative Email: jxeurep111@hotmail.com

Please retain your proof of purchase for warranty purposes.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.