TIYPEOR 70mm LED Angel Eyes

Contents

TIYPEOR 70mm LED Angel Eyes Motorcycle Lights User Manual

Model: 70mm LED Angel Eyes

1. Product Overview

The TIYPEOR 70mm LED Angel Eyes are waterproof COB circle lights designed as logo backlights for BMW motorcycles. These lights offer both white and yellow illumination, with the yellow function typically serving as a turn signal. The product is designed for durability and visibility, enhancing the aesthetic and safety features of your motorcycle.

TIYPEOR 70mm Yellow/White Logo Light installed on a BMW motorcycle

Figure 1: TIYPEOR 70mm Yellow/White Logo Light installed on a BMW motorcycle.

Video 1: Product demonstration showing white and yellow light functions.

2. Package Contents

Please check the package for the following items:

  • 2 x TIYPEOR 70mm LED Angel Eyes Rings (White/Yellow)
  • 2 x Control Boxes/Drivers
  • Wiring Harness
  • Instruction Manual (PDF available online: User manual (PDF))
Product packaging and components including LED rings, control boxes, and wiring

Figure 2: Product packaging and components.

3. Setup and Installation

Installation requires basic electrical knowledge and tools. If you are unsure, it is recommended to seek professional assistance.

3.1 Wiring Diagram

Wiring diagram for RGB and Yellow/White versions of the LED lights

Figure 3: Wiring diagram for Yellow/White LED lights.

3.2 Connection Instructions (Yellow/White Version)

The Yellow/White version of the lights typically functions with your motorcycle's turn signal system.

  • Positive pole (White Light): Connect this wire to a constant 12V positive power source, or a circuit that activates when the motorcycle is on (e.g., parking light circuit).
  • Negative pole: Connect this wire to the motorcycle's chassis ground or a negative terminal.
  • Positive pole (Yellow light A): Connect this wire to the positive wire of your left turn signal.
  • Positive pole (Yellow light B): Connect this wire to the positive wire of your right turn signal.

Note: The cable length from the LED ring to the control box is approximately 60cm, and the main wiring harness from the control box is approximately 50cm.

3.3 Mounting

  1. Identify a suitable flat surface on your motorcycle's fairing where the 70mm LED ring can be securely mounted.
  2. Clean the mounting surface thoroughly to ensure good adhesion.
  3. Secure the LED ring in place. You may need to use adhesive or mounting brackets (not included) depending on your motorcycle model.
  4. Route the wiring harness safely, away from hot engine parts or moving components, and secure it with zip ties.
  5. Connect the wires as per the instructions above.
  6. Test the lights before fully reassembling any removed motorcycle parts.

4. Operating Instructions

Once properly installed and wired, the TIYPEOR 70mm LED Angel Eyes will operate in conjunction with your motorcycle's electrical system.

  • White Light: The white light will illuminate when its connected power source is active (e.g., when the motorcycle is turned on or parking lights are engaged).
  • Yellow Light (Turn Signal): The yellow light will activate and flash when the corresponding turn signal (left or right) is engaged, overriding the white light during its operation.

5. Maintenance

The TIYPEOR LED Angel Eyes are designed for durability with an IP68 waterproof rating, requiring minimal maintenance.

  • Cleaning: Periodically wipe the LED rings with a soft, damp cloth to remove dirt and debris. Avoid using abrasive cleaners or solvents.
  • Inspection: Regularly check the wiring for any signs of wear, fraying, or loose connections. Ensure the lights are securely mounted.

6. Troubleshooting

  • Lights not turning on:
    • Check all wiring connections to ensure they are secure and correctly matched (positive to positive, negative to negative).
    • Verify that the power source is active and providing 12V.
    • Check for any blown fuses in the motorcycle's electrical system related to the connected circuit.
  • Only one color working (e.g., only white, no yellow):
    • Ensure the specific wire for the non-working color is correctly connected to its intended signal (e.g., turn signal positive).
    • Inspect the wiring for any breaks or shorts.
  • Lights flickering:
    • Check for loose connections.
    • Ensure the power supply is stable and within the specified voltage range.

7. Specifications

FeatureSpecification
Brand NameTIYPEOR
OriginMainland China
Size70mm (Diameter)
Waterproof RatingIP68
CompatibilityFor BMW Motorcycles (verify logo diameter)
Battery IncludedNo
High-concerned chemicalNone

8. User Tips

  • Logo Compatibility: The original BMW emblem may not fit directly over the LED ring. Consider using flat adhesive logos or a thin (1mm) 70mm round acrylic sheet between the light and the logo for a better fit.
  • Enhanced Waterproofing: While rated IP68, some users recommend applying transparent silicone to the back of the LED strip for additional waterproofing, especially in harsh weather conditions.
  • Brightness: Users have noted the lights are very bright, providing excellent visibility.
  • Professional Installation: If you encounter difficulties with wiring or mounting, especially if cables do not reach intended connection points, consider consulting an offline repair shop for professional installation and wiring harness modification.

9. Frequently Asked Questions (FAQ)

Q: Do these lights function as turn signals in yellow?
A: Yes, these lights are designed with a steering function, meaning the yellow light can operate as a turn signal.
Q: Are these LEDs compatible with my BMW 1250 GS?
A: Compatibility depends on the diameter of your motorcycle's existing logo. Please measure your car logo's diameter first to ensure it matches the 70mm size of these lights. Some models might be better suited for a 60mm product if available.
Q: I'm having trouble with the wiring, especially reaching the rear turn signals.
A: If the cables do not reach or you are unsure about the installation, it is recommended to visit an offline motorcycle repair shop. They can assist with installation and may be able to add a custom wiring harness if needed.

10. Warranty and Support

10.1 TIYPEOR Warranty

TIYPEOR represents and warrants to the first end-user that the Product shall materially conform to TIYPEOR's published specifications in the user manual, subject to the terms and conditions below.

TIYPEOR Warranty information details

Figure 4: TIYPEOR Warranty Information.

  • Warranty Period: One Year (12 Months) from the date a new product is first delivered to the End-User after being purchased.
  • What is Covered: The Standard Warranty provides support from TIYPEOR, including replacement parts and shipping costs during the Warranty Period. Customers will be covered for

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.