TAPNM Dynamic Scanning LED Side Marker Lights

Contents

Dynamic Scanning LED Side Marker Lights User Manual

Model: Dynamic Scanning LED Side Marker Lights

Brand: TAPNM

Introduction

Thank you for choosing the Dynamic Scanning LED Side Marker Lights. These lights are designed to enhance the appearance and safety of your vehicle with their dynamic scanning and switchback Daytime Running Light (DRL) features. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your product.

Vehicle Compatibility

These side marker lights are compatible with the following vehicle models:

  • Chevy Camaro: LS, LT, SS, RS, ZL1 (2016-2023 models)
  • Cadillac CTS: (2014-2021 models)
  • Cadillac ATS: (2015-2021 models)

Replaces OEM Part Numbers: 23169181, 23169182, 20896549, 20896550.

Compatible Models and OEM Part Numbers
Image: Compatible vehicle models and corresponding OEM part numbers.

Installation Guide

The installation process is designed to be quick and straightforward, typically taking about 15 minutes. These lights feature a plug-and-play design, requiring no additional wiring or modifications to your vehicle's original housing.

Step-by-Step Installation:

  1. Remove Screws: Carefully remove any screws securing the existing side marker light assembly.
  2. Remove Retaining Clips: Detach any retaining clips that hold the OEM housing in place.
  3. Remove OEM Housing: Gently pull out the original side marker light housing.
  4. Remove Little Bulbs: Disconnect and remove the small bulbs from the OEM housing.
  5. Plug T10 Wire into Connector: Insert the T10 wire from the new LED side marker light into the vehicle's connector.
  6. Tidy Up & Tuck It Back In: Neatly arrange the wiring and tuck it back into the vehicle's fender well.
  7. Twist and Make Sure No Gap: Position the new LED side marker light, twisting it slightly to ensure a snug fit without any gaps.
  8. Plug In New Light: Securely plug the new LED side marker light into its designated slot.
  9. Test the Function: Turn on your vehicle's lights to verify that the new side marker lights are functioning correctly.
Installation Steps for Side Marker Lights
Image: Visual guide for the 9-step installation process.

Operation

These side marker lights feature a dynamic scanning sequence upon startup, followed by a steady Daytime Running Light (DRL) mode. The dynamic scan lasts approximately 5-10 seconds before transitioning to DRL.

Video: Demonstration of the dynamic scanning and DRL features upon vehicle startup.

The lights are equipped with 64 high-power SMD LED chips, providing 5500K white light output. They are designed to be 5 times brighter than standard OEM lights, while consuming 70% less energy.

Upgrade Version Features
Image: Highlights of the upgraded version, including dynamic animation, DRL, energy efficiency, extended lifespan, and increased light output.

Maintenance

These LED side marker lights are designed for ultra-durability and minimal maintenance. They feature an IP67 weather-sealed rating, ensuring resistance against water, dust, and shock. The robust ABS housing and PC smoke lens contribute to their long lifespan of over 55,000 hours.

IP67 Waterproof Feature
Image: Demonstrates the IP67 waterproof rating, indicating readiness for various weather conditions like light snow, sand, lightning, and general water exposure.

To clean the lights, simply wipe them with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the lens or housing.

Troubleshooting

The side marker lights are designed to be error-free and prevent flickering. If you encounter any issues, please refer to the following:

  • Lights not turning on: Double-check all connections to ensure they are secure and properly seated. Verify that the vehicle's lighting system is functioning correctly.
  • Flickering: Although designed to be flicker-free, if flickering occurs, ensure the electrical connection is stable and free from corrosion.
  • Inconsistent dynamic scan: Ensure the vehicle's electrical system is providing stable 12V power.

If problems persist after following these steps, please contact customer support for further assistance.

Specifications

Feature Detail
Voltage 12 V
Wattage 5 W
LED Count 64 high-power SMD LEDs
Light Color Temperature 5500K (White)
Housing Material ABS Plastic
Lens Material PC Smoke Lens
Lifespan 55,000+ hours
Waterproof Rating IP67 Weather-sealed
Certifications DOT/SAE Certified
Installation Plug & Play, Direct OEM Replacement

Dimensions:

Product Dimensions
Image: Detailed product dimensions for both front and rear lights, along with features like Plug & Play design and DOT/SAE certification.
  • Length: 180 mm (7.08 in)
  • Width: 166 mm (6.5 in)
  • Height: 39.5 mm (1.55 in)

Warranty and Support

For any defective products or issues, please contact our customer service. We are committed to providing a satisfactory solution and typically respond within 24 hours (excluding weekends and holidays).

User Tips

  • Ensure your vehicle's ignition is off before beginning installation to prevent electrical issues.
  • Test the lights immediately after installation to confirm proper function before fully reassembling your vehicle's components.
  • The plug-and-play design makes installation simple, but always double-check connections for a secure fit.
  • Enjoy the enhanced visibility and modern aesthetic provided by the dynamic scanning and DRL features.

© 2023 TAPNM. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.