1. Important Safety Information
WARNING: Electric bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle. It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists.
1.1 Product Safety Notice
- Always wear a helmet when riding your electric bike.
- Keep the two keys properly. If the unique keys are lost, you will not be able to turn on the bike or replace the battery. If necessary, you should get more spare keys.
- Make sure your electric bike has a full battery before taking it out to ride.
- Always be aware of local road laws, and follow them.
- Do not ride the bike under the influence of drugs or alcohol.
- Always respect pedestrians.
- Do not ride under wet conditions. The electric bike may slide from under your feet causing injury. Wet conditions may damage the electronics and void the warranty.
1.2 Warning Message
- Avoid water - The electric bike is not waterproof. The electronics may be damaged due to water and water damage is not covered by our warranty. Riding in wet conditions is also very dangerous and may result in injury.
- Avoid prolonged exposure to sun or rain and avoid storage in places with high temperatures or corrosive gas.
- Abuse - We do not cover physical damage due to negligent care and extreme riding.
- Whenever you ride the Electric Bike, you risk severe injury or even death from loss of control, collisions, and falls. Use caution and ride at your own risk.
- Do not modify the product from manufacturer's original design.
- Do not exceed the posted speed limit and obey all traffic laws.
- Avoid touching the charging port directly and do not let it make contact with a metal object.
- Keep hands and all body parts away from moving parts while operating the electric bike.
- Before riding - be sure to check the electric bike over and make sure the electric bike is operating correctly before each use.
- Before riding - be sure to check that the braking system is functioning properly; also be sure to check that all safety labels are in place and you understand the safety warnings.
- Before riding - be sure that any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition.
- Before riding - be sure to check that the tires are in good condition, inflated properly, and have sufficient tread remaining.
- The electric bike should never be used by children under the age of 18.
- Make note that additional insurance may be required to cover situations you encounter while riding an electric bike. It is recommended that you contact an insurance company or broker for advice and consultation.
- To conserve electricity, use assist mode, and avoid zero starting, frequent braking, driving against the wind, carrying heavy loads including other people and riding with insufficient air pressure.
1.3 Disclaimer
⚠️ Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
2. Product Overview
2.1 Package Contents
Carefully check package contents. If anything is missing or damaged, please contact customer service.
Unpack the bike. Open the bike box and remove the small box inside. With the help of another person capable of safely lifting a heavy object, remove the bike from the bike box. Carefully remove the packaging material protecting the bike frame and components. Please recycle packaging materials, especially cardboard and foam, whenever possible. Open the small box and carefully set out all contents.

2.2 Parts Identification

3. Assembly
The following assembly steps are a general guide. If you are unable to install after reading the instructions, contact customer service for assistance.
3.1 Front Fork and Wheel Assembly
- Remove the front wheel and install it on the front fork.
- Then install the front wheel anti-spin hook and nut, and tighten them.

3.2 Fender & Headlight Assembly
- Take out the fender, remove the nut, washer, and bolt at the top of the front fork.
- Fix the headlight and fender to the fixed position on the front fork with screws.
- Use a cross screwdriver to loosen the screw at the rear mudguard clip position, then separate the clip by hand and hook it under the saddle tube clamp.
- Adjust to the proper position and tighten the screws with a cross screwdriver to secure the mudguard.
- Locate the headlight wiring harness and the main wiring harness, which have arrow markings. Align them with the arrows and insert them into the harness, then confirm that they are securely plugged in.
- Then, secure the mounting brackets on both sides with screws.
3.3 Stem Assembly
- Loosen the screws to remove the front fork sleeve.
- Take out the stem and insert it into the front frame.
- Tighten the screws to fix the stem in place.
- After making sure the stem is aligned with the direction of the tire, tighten the clamping screws below the stem to fix the direction.
3.4 Kickstand Assembly
- First, you need a screwdriver to fix the screws on the kickstand.
- Secure the kickstand to the designated position of the bike.
- Fasten the screws on the right.
- Finally, fix the screws on the left side, making sure they are locked to prevent them from falling off during riding.
3.5 Pedals Assembly
- Locate the right-side / left-side pedal, which is marked "R," "L," should have an "R"/"L" sticker attached.
- Thread the right pedal onto the right crank gently by hand, turning clockwise. Then tighten pedal by allen wrench.
- Thread the left pedal onto the left crank gently by hand, turning counter-clockwise. Then tighten pedal by allen wrench.
- Check the chain alignment. Rotate the right pedal and crank toward the back of the bike as though pedaling backward. Watch the chain and ensure the chain runs through the drivetrain (the rear cog, chain tensioner, and around the front chain ring) smoothly.
Note: If the pedal/chain doesn't run smoothly or something seems misaligned, please contact Electric Bike Support at support@ride-ebike.com.
3.6 Seat Assembly
- Loosen the quick-release screws on the saddle clamp to install the seat post.
- Move the seat up and down by sliding the seat post in or out of the seat tube.
- Tighten the screws to fix the seat post in place.
- After making sure the stem is aligned with the direction of the tire, tighten the clamping screws below the seat post to fix the direction.
Positioning the seat at the right height is important for better pedaling, safety, and overall riding comfort. The rider's leg length is used to determine the seat's position. When you pedal, your hips should remain level and your legs should be almost fully extended at the bottom of the pedal stroke, but not over-extended.
To determine the right seat height, sit on the eBike with one pedal at its lowest point and place the ball of your foot on the pedal. Your leg should be almost fully extended (not locked out) with a slight bend at the knee.
3.7 Rear Rack and Seat Bag Installation
Adding a rear rack depends on whether you have one or not.
- Locate the taillight, loosen the taillight screws, and remove the taillight.
- Unscrew all four screws on the back.
- Then place it in the rear shelf, align the holes, and tighten the screws on both sides.
- Locate the taillight wiring and tie it up with the cable ties that come with the vehicle.
- Place the rear seat bag as shown in the picture, then tighten the fixing screws above the rear fender.
4. Operation
4.1 Battery Removal and Installation
- Insert the key and turn it counterclockwise to the left; the battery will pop out.
- Then remove the battery and lift it upwards.
When Removing the Battery:
Be careful not to drop or damage the battery once it is loose from the bike. Avoid damaging the exposed connector terminals and keep them clear of debris.
When Installing the Battery:
Ensure the battery is turned off before sliding it into the frame mount receptacle. Do not force the battery onto the receptacle. Slowly align and push the battery down into place. Before each use, ensure the battery has been properly secured by carefully pulling upwards on it with both hands to test the attachment.

4.2 Charging Your E-Bike
Before using the electric bike, you must fully charge the battery.
- Ensure the battery is off, by rotating the key to align with the off icon.
- Remove the rubber cover on the charging port on the opposite side of the battery from the key switch.
- Plug the charger into the battery's charging port. With the battery on or off the bike, place the charger in a flat, secure place, and connect the DC output plug from the charger to the charging port on the side of the battery.
- Plug the charger into a power outlet. Charging should initiate and will be indicated by the LED charge status lights on the charger turning red. Once fully charged, the charging indicator light turning green. Unplug the charger from the wall outlet first and then remove the charger output plug from the battery charging port.

Attention:
Before charging, make sure that the charger light faces upwards; full charge normally takes 3-7 hours; charge the battery in a clean and safe place and do not overcharge.

4.3 Instrument Usage and Speed Adjustment
The instrument panel provides essential information and controls for your electric bike.

Instrument Operating Instructions:
- Power on/off: Press and hold the [Power button] for 2 seconds to power on or off.
- Gear shifting: Double-click the [Function Key] to cycle through gears 1-3.
- Kilometers/miles switch: Triple-click the function key to switch between kilometers/miles and public miles.
- Zero/Non-Zero Startup: Five presses of the [Function Key] button to switch between zero and non-zero startup.
- Parameter Setting: Simultaneously press the [Function Key] and [Power Key] for 5 seconds to enter parameter setting mode.
Setting Menu Operations:
To access general settings: Press and hold both the [+ button] and [- button] simultaneously to enter the general settings menu.
- Switch setting items: In the settings menu, press the [Power button] briefly to toggle between options.
- Adjust setting parameters: Press the [+ button] or [- button] briefly to modify parameters.
- Confirm: Press and hold the [Power button] to save changes and return to the previous level.
- Return to home page: Press and hold the [- button] to exit without saving and return to the main interface, or remain inactive on the page for 60 seconds to automatically exit the settings menu and return to the home page.
SETTING MENU Options:
- SET 1: Wheel Diameter (Adjustable range: 16-29 inches, default: 26 inches. Not adjustable by default.)
- SET 2: Speed Limit (Select any value within the adjustable range (1-99), default: 25 km/h. Not adjustable by default.)
- SET 3: Unit (Options: Metric (KM/H) or Imperial (blank), default: KM/H.)
- SET 4: Screen Brightness (Adjustable range: 1-3 levels, default: Level 3.)
- SET 5: Auto Sleep Time (Adjustable range: 1-60 minutes, default: 10 minutes.)
- SET 6: Single Trip Auto Reset (Options: Set to "y" to clear the single trip mileage on startup, or set to "n" to retain the single trip mileage on startup.)
4.4 Brake Adjustment
Before aligning the mechanical disc brake, make sure that the brake cable is properly inserted into the lock lever. If the disc rotor is bent or damaged, replace the rotor first.
Brake Noise Adjustment:
- Prepare tools and locate: Locate the disc brake caliper (the metal part that holds the brake disc). You will see two vertical screws on the caliper (usually an M6 Allen wrench is used). Prepare the appropriate tools.
- Loosen the screws: Use an M6 Allen wrench to slightly loosen these two screws. Note: Only loosen them by one to one and a half turns, allowing the caliper to move slightly left and right. Do not completely remove the screws!
- Alignment Position: Gently straighten the wheel with your hand, ensuring it is centered on the frame. Now, use your hand to slightly adjust the position of the brake caliper, moving it left and right. Your goal is to align the brake disc exactly in the center of the two brake pads, with even clearance on both sides. While adjusting, gently rotate the wheel with your other hand, judging by the sound. The optimal position is when it rotates smoothly without any friction noise.
- Keeping the clamp in the optimal position, alternately and gradually tighten the two loosened screws. Do not tighten one screw completely at once, as this can easily cause the position to shift again.
After the screws are fully tightened, quickly rotate the wheel one last time to confirm that there are no abnormal noises. If there is still slight friction, repeat steps 2-3.
4.5 Gear Operation
Multi-speed bicycles can have internal or derailleur gear systems. Improper shifting can result in the chain jamming or becoming derailed, leading to loss of control or a crash. Always be sure the chain is fully engaged in the desired gear before pedaling hard.
Avoid shifting while standing up on the pedals or under load.
To shift properly, pedal the bicycle with little pressure on the pedals, and move the shifter one gear at a time, ensuring that the chain is fully engaged in that gear before applying more pressure on the pedals. For bicycles with 3 front chain rings, avoid "Cross Chaining," which is the position when the chain is in the smallest cog in the rear combined with the inner or smallest chain ring in the front or the largest cog in the rear and the outer or largest chain ring in the front. These gear positions put the chain at the most extreme angle and can cause premature wear to the drivetrain. Bicycles with 3 front chain rings have enough gear "overlaps" that these gears are not needed.

5. Maintenance
Regular inspection and maintenance are key to ensure bikes function as intended, and to reduce wear and tear on their systems. Recommended service intervals are meant to be used as guidelines. Real-world wear and tear, and the need for service, will vary with conditions of use. We generally recommend inspections, service, and necessary replacements be performed at the time or mileage interval that comes first.
5.1 Daily Care and Maintenance
Cleaning and Storage:
- If you see stains on the bike body, wipe them off with a damp cloth. If the stains won't scrub off, put on some toothpaste, and brush them with a toothbrush, then wipe them off with a damp cloth.
- Do not clean the bike with alcohol, gasoline, kerosene, or other corrosive and volatile chemical solvents to prevent dire damage. Do not wash the bike with a high-pressure water spray. During cleaning, make sure that the bike is turned off, the charging cable is unplugged, and the rubber flap is closed, as water leakage may result in electric shock or other major problems.
- When the bike is not in use, keep it indoors where it is dry and cool. Do not put it outdoors for a long time. Excessive sunlight, overheating, and overcooling accelerate the battery pack's lifespan.
Battery Maintenance:
- Use original battery packs; use of other models or brands may bring about safety issues.
- Do not touch the contacts. Do not dismantle or puncture the casing. Keep the contacts away from metal objects to prevent short circuits which may result in battery damage or even injuries and deaths.
- Use original power adapter to avoid potential damage or fire.
- Mishandling of used batteries may do tremendous harm to the environment. To protect the natural environment, please follow local regulations to properly dispose of used batteries.
- After every use, fully charge the battery to prolong its lifespan.
Storage and Disposal:
- Please try to store the bike in a cool and dry place between 50°F-77°F (10°C-25°C). In extremely humid environments, the interior of the bike may suffer condensation or even water accumulation, which may damage the battery rapidly. Devices are not intended for use at elevations greater than 2000m above sea level. Prolonged exposure to UV rays, rain, and the elements may damage the enclosure materials; store indoors when not in use.
- In daily use, try to avoid recharging the bike after completely exhausting the battery. If the battery is low, charge it as soon as possible.
- Please charge the bike every other month to preserve the battery.
5.2 Recommended Service Intervals
| Interval | Inspect | Service | Replace |
|---|---|---|---|
| Weekly (100-200 mi / 160-321 km) | Check drivetrain for proper alignment and function. Check wheel trueness and for quiet wheel operation. Check condition of frame for any damage. | Clean frame by wiping with damp cloth. Use barrel adjuster(s) to tension derailleur/brake cables if needed. | Any components confirmed damaged by Product Support or a certified mechanic. |
| Monthly (250-750 mi / 402-1207 km) | Check bike is shifting properly. Check chain stretch. Check brake and shifter cables for corrosion or fraying. Check spoke tension. Check accessory mounting. | Check crankset and pedal torque. Clean brake and shift cables. True and tension wheels if loose spokes are discovered. Balance the battery. | Brake and shift cables if necessary. Brake pads if necessary. |
| Every 6 Months (750-1250 mi / 1207-2011 km) | Inspect drivetrain. Inspect all cables and housings. | Standard tune-up by certified mechanic. Grease bottom bracket. | Brake pads. Tires if necessary. Cables and housings if necessary. |
6. Troubleshooting
6.1 Basic Troubleshooting
| Symptoms | Possible Causes | Most Common Solutions |
|---|---|---|
| The bike does not work | 1. Insufficient battery power 2. Faulty connections 3. Battery not fully seated in tray 4. Improper turn on sequence 5. Brakes are applied | 1. Charge the battery 2. Clean and repair connectors 3. Install battery correctly 4. Turn on bike with proper sequence 5. Disengage brakes |
| Irregular acceleration and/or reduced top speed | 1. Insufficient battery power 2. Loose or damaged throttle 3. Misaligned or damaged magnet ring | 1. Charge or replace battery 2. Replace throttle 3. Align or replace magnet ring |
| The motor does not respond when the bike is powered on | 1. Loose wiring 2. Loose throttle 3. Loose motor plug wire | 1. Repair and or reconnect 2. Tighten throttle 3. Secure motor plug wire. |
| Reduced range | 1. Low tire pressure 2. Low or faulty battery 3. Driving with too many hills, headwind, braking, and/or excessive load 4. Battery discharged for long period of time without regular charges, aged, damaged, or unbalanced 5. Brakes rubbing | 1. Adjust tire pressure 2. Check connections or charge battery 3. Assist with pedals or adjust route 4. Balance the battery; contact tech support if range decline persists 5. Adjust the brakes |
| The battery will not charge | 1. Charger not well connected 2. Charger damaged | 1. Adjust the connections 2. Replace |
| Wheel or motor makes strange noises | 1. Loose wheel spokes or rim 2. Loose motor wiring | 1. Tighten, repair, or replace 2. Reconnect motor. |
You can contact the customer service of the platform you purchased from.
6.2 Fault Code Comparison Table
When a fault occurs, the red fault indicator on the instrument panel lights up. The instrument interface will flash the fault information as a reminder and display the "Error" prompt.
| No. | Data Status | Meaning | Instrument Display |
|---|---|---|---|
| 1 | 0x21 | Controller Fault | 21 |
| 2 | 0x22 | Throttle Fault | 22 |
| 3 | 0x23 | Motor Phase Loss | 23 |
| 4 | 0x24 | Hall Sensor Fault | 23 |
| 5 | 0x25 | Undervoltage Protection | 25 |
| 6 | 0x26 | Brake Lever Fault | 26 |
| 7 | 0x30 | Communication Fault | 30 |
7. Specifications
This user manual is a general version, using a 48V 10Ah battery capacity as an example (specific parameters may vary depending on the product you purchase).
7.1 General Specifications
| Item | Specifications |
|---|---|
| Model | M10/M12 |
| Product Dimensions | 135*22*72 (cm) |
| Package Dimensions | 168*23*98 / 168*25*104 (cm) |
| E-Bike Weight | 50.7lb (23kg) / 55.1lb (25kg) |
| Battery | 48V 10Ah |
| Charger | 54.6V 2A |
| Charging Time | 3-6 Hours |
| Tire Pressure | 40-65 PSI |
| Bell/Horn | Electric Horn Installed |
| Frame Material | High Carbon Steel |
7.2 Detailed Parameters
| Category | Item | Parameters |
|---|---|---|
| Basic parameters | Dimensions | 107*20*58.5 CM |
| Wheel dimension | 14" | |
| Frame material | Iron | |
| Load capacity | 120KG | |
| Scooter weight | 25.6KG | |
| Max. speed | 20MPH/H | |
| Performance Parameters | Max. gradient | 9-10° |
| Front derailleur | Three-speed | |
| Rear derailleur | NA | |
| Working temperature | -10°C~55°C | |
| Battery parameters | Rated voltage | 48V |
| Battery capacity | 15/17.5AH | |
| Motor parameters | Rated power of motor | 500W P≤740w |
| Motor type | Brushless hub motor | |
| Input voltage | 110-260V DC | |
| Input current | ≤2.8A | |
| Charger parameters | Output voltage | 54.6V |
| Output current | 2A | |
| Charging time | 5-7H | |
| Other parameters | Instrument | LCD instrument |
| Brake | Front and rear wheels: Disc brake | |
| Anti-vibration mounting | Four shock absorbers | |
| Car light | Front and rear lamps and brake taillight | |
| Package weight | 33KG |
8. Warranty and Support
8.1 After-Sales Services
| Category | Components | Warranty period |
|---|---|---|
| Power system | Battery | 12 months |
| Motor | 12 months | |
| Electrical system | Controller | 12 months |
| Instrument | 6 months | |
| Power-off brake handle | 6 months | |
| Key switch | 6 months | |
| Headlamp | 6 months | |
| Variable speed system | Left and right thumb shifters | 6 months |
| Fluted disc | 6 months |
Notice:
Consumables and gift items are not included in the after-sales service. Warranty provisions cease to apply to any of the following conditions, which are not quality problems:
- Faults caused by operation not in accordance with the user manual.
- Normal wear, accident, abuse, neglect, improper assembly, or improper maintenance of parts, and improper use of accessories by any user.
- Parts that are subject to natural wear under normal use, or the circumstances inapplicable to the above warranty policy.
- Failure of correct change and maintenance or faults and damage of other parts due to wear of consumables.
- The warranty card does not match the scooter model or the scooter model is changed.
- Damage caused by overloading, riding over obstacles (including but not limited to going down steps and falling), extreme sports, etc.
- Damage caused by force majeure (such as fire, earthquake, lightning strike and flood).
- Within the range of warranty policy, but beyond the warranty date.
- Generally, a fully charged battery will endure 90 days in standby mode. Charge the battery after using every time. Depletion of battery power may damage battery permanently and the electronic device inside the battery will record the charge and discharge of the battery. Damage caused by over-discharge or under-discharge is not covered by warranty service.
- Damage caused by collision during the use of the product and its parts.
For any questions, please feel free to contact us. We will send you a reply and solve the problem within 24 hours. Email: upleeshop@outlook.com
9. User Tips
- The product you receive should match the images and description provided.
- For extended battery life and range, utilize assist mode, avoid frequent braking, and maintain proper tire pressure (35-65 PSI).
- If using the bike for transportation, especially if you have health considerations, ensure you are comfortable with its operation and adhere to all safety guidelines.
- Always check tire pressure before riding; sufficient pressure is crucial for safety and performance.
- To conserve electricity, use assist mode, and avoid zero starting, frequent braking, driving against the wind, carrying heavy loads including other people and riding with insufficient air pressure.