1. Introduction
The KuWFi Outdoor Wireless Bridge is designed to transmit and receive wireless signals over long distances, effectively acting as a wireless Ethernet cable. This device is ideal for extending network coverage for applications such as IP cameras, CCTV systems, and general long-range WiFi extension.
It operates on the 2.4GHz band with a maximum rate of 300Mbps and supports point-to-point (PTP) and point-to-multipoint (PTMP) connections up to 1KM under optimal conditions. The device features an IP65 waterproof, dustproof, and sunscreen housing, making it suitable for various outdoor environments. It also supports 24V passive PoE for flexible power options.
Essential Usage Rules
- Not a WiFi Router: The bridge itself does not broadcast a WiFi signal for direct connection by phones or laptops. An external Access Point (AP) or Router is required at the receiving end to provide WiFi access.
- Pre-Paired at the Factory: Your bridge kit comes pre-configured. Avoid changing the WiFi SSID or password unless necessary, as this will disconnect the devices.
- Avoid Settings Modification: Modifying factory settings can lead to automatic disconnection. If this occurs, manual re-pairing will be required.
2. Package Contents
Please check the package for the following items:
- 2x 2.4GHz CPE Bridge Units
- 2x POE Power Supply Adapters
- 2x Network Cables
- 1x Quick Setup Manual (PDF available online)

3. Setup
3.1 Device Overview


3.2 Initial Connection for Configuration
It is recommended to use a wired connection for initial setup and configuration.
Method 1: Wired Connection
- Connect one end of the network cable to the POE port of the POE adapter.
- Connect the other end of the network cable from the POE adapter's LAN port to your PC's network port.
- Connect the CPE Bridge to the POE port of the POE adapter.

Method 2: Wireless Connection (for initial access if wired is not feasible)
On your PC, search for the CPE's WiFi SSID: 'Wireless XXXX' (where XXXX are the last four digits of the device's unique identification number).
3.3 Configuring PC IP Address for Web UI Access
To access the device's web management interface, you need to set a static IP address on your PC.
- Find the network icon in the lower right corner of your screen and click 'Open Network and Internet Settings'.
- Select 'Ethernet' and click 'Change adapter options'.
- Right-click on your active network connection and select 'Properties'.
- Double-click 'Internet Protocol Version 4 (TCP/IPv4)'.
- Select 'Use the following IP address:' and enter:
- IP address:
192.168.1.10 - Subnet mask:
255.255.255.0
- IP address:
- Click 'OK' to confirm.

3.4 One-Touch Automatic Pairing
The bridges are pre-paired, but if a connection is lost or for initial setup, you can re-pair them:
- Power on both bridge units.
- Set Modes: Move the toggle switch on one CPE to the 'A' position (Master AP) and the other CPE to the 'C' position (Slave AP).
- Simultaneously press the RST buttons on both the Master AP and Slave AP for 1 second.
- Wait briefly; the devices will automatically search and pair with each other.

3.5 Switch Master/Slave Bridge Mode
The A/C switch on the device determines its role:
- A (AP Mode): When the toggle switch is positioned on the side marked 'A', this outdoor CPE functions as the Master AP (Transmitter).
- C (Client Mode): When the toggle switch is positioned on the side marked 'C', this outdoor CPE functions as the Slave AP (Receiver).

4. Operating Instructions
4.1 Accessing the Web Management Interface (WEB UI)
Open a web browser (Google Chrome recommended) and enter one of the following IP addresses:
- Master AP:
192.168.1.88 - Slave AP:
192.168.1.89
The default password is admin.

4.2 Checking Device Status
After logging in, you can view the bridge's status and operating mode on the home page.

4.3 Wireless Settings
Users can modify the SSID name and password for the wireless bridge, and switch to alternative encryption methods.

4.4 Advanced Wireless Settings
Configure region, wireless transmission power, channel, and bandwidth for optimal performance.

4.5 Network Settings
The CPE supports dynamic and static IP addresses. No additional configuration is required under normal circumstances.

4.6 Cloud Settings
The CloudAC platform allows for centralized management of your devices, including gateways, billing, and CloudAP. You can view and manage your devices in the cloud, check device running status, and modify configurations.

4.7 Ping Watchdog Settings
This feature monitors network connectivity by sending ping packets to a target IP/domain. If no response is received, it can trigger alerts or preset actions (e.g., device restart) to help resolve connectivity issues.

4.8 Scheduled Reboot Settings
Scheduling reboots for CPE equipment helps clear cached files and ensures correct device operation. It is strongly recommended to configure scheduled reboots.

5. Maintenance
5.1 System Settings
The System settings page allows users to upgrade firmware, back up current configuration files, and reboot the device.

5.2 Physical Maintenance
The KuWFi CPE Bridge features an outdoor ABS plastic shell with professional lightning protection and IP65 water-proof and dust-proof ratings. This design ensures suitability for multiple harsh environments. Regular visual inspection for physical damage is recommended.
5.3 Safety Precautions
- Do not use incorrect or unauthorized chargers.
- Do not use metallic objects to contact short circuit electrodes.
- Do not get the device wet.
- Do not expose to excessive heat, humid, or corrosive environments.
- It is recommended to use the device under the guidance of professionals or with adequate professional knowledge.

6. Troubleshooting
6.1 Re-pairing Devices
If the connection is lost due to misconfiguration, use one of the following two methods to restore it:
Method 1: One-Key Reset (Quickest)
- Power on both bridge units.
- Press the Reset button on both devices simultaneously for 1 second.
- The units will automatically search and pair with each other.
Method 2: Manual - Web Backend Setup
If you prefer using the management interface:
- Master Bridge (Transmitter): Set the mode to 'AP Mode'.
- Slave Bridge (Receiver): Set the mode to 'Repeater/Client Mode'.
- Connection: In the Slave Bridge settings, use the "Scan" function to find the Master Bridge's SSID and click "Connect" to complete the pairing.
6.2 Frequently Asked Questions (FAQ)
- Q1: How to pair Bridges?
- A1: Set one Bridge as Master ('A' switch) and the other as Slave ('C' switch). Simultaneously press the 'RST' button on both Bridges for one second. They will automatically pair.
- Q2: I cannot access the WEB UI page for IP Address configuration.
- A2: Ensure your computer is connected to the bridge and has a static IP address set (e.g., 192.168.1.10, Subnet mask: 255.255.255.0). Then open a browser and input 192.168.1.88 (for AP) or 192.168.1.89 (for Repeater). Remember to restore your PC's original network settings after configuration.
- Q3: Outdoor Wi-Fi bridge range is less than described distance?
- A3: Transmission distance is affected by many factors like local network conditions, buildings, trees, etc. Ensure a clear line of sight and avoid obstacles as much as possible during installation.
- Q4: The bridge Wi-Fi signal is weak or transmission distance is short?
- A4: Adjusting the WiFi protocol and bandwidth of the bridge can affect network speeds and transmission distances. Continuous debugging may be needed to find the best state for your specific environment and requirements.
- Q5: Does the bridge support 360-degree signal transmission?
- A5: No, the bridge uses panel antennas and does not support 360-degree transmission. For optimal stability, install the two Bridges face-to-face.
- Q6: Can't find a Wi-Fi signal?
- A6: Different countries support different WiFi channels. Log into the WEB UI page to change the country region of the WiFi signal or try another channel.
- Q7: Outdoor Wi-Fi bridge is not powered.
- A7: Ensure the product's WAN or POE port is correctly connected to the adapter's POE port. If still unpowered, try changing the adapter and RJ45 LAN cable.
7. Specifications
| Feature | Description |
|---|---|
| Brand Name | KuWFi |
| Model | B403 |
| Type | Wireless |
| Application | Outdoor |
| Wi-Fi Supported Frequency | 2.4G (2.412 GHz ~ 2.484GHz) |
| Wi-Fi Transmission Standard | 802.11b/g/n |
| 2.4G Wi-Fi Transmission Rate | 300 Mbps (Max. LAN Data Rate: 300Mbps) |
| Wired Transfer Rate | 10/100Mbps |
| LAN Ports | LAN1: 1x 10/100Mbps, LAN2: 1x 10/100Mbps (Supports 24V POE) |
| WAN Ports | 2 x10/100Mbps |
| Antenna Type | Built-in Panel Antenna |
| Point to Point Distance | Up to 1KM (Test under optimal conditions) |
| Power Supply Method | POE 24V/0.5A or DC 12V/1A (DC Power not included) |
| Encryption | WPA/WPA2, WPA-PSK/WPA2-PSK |
| Operating Temperature | -30°C to 55°C |
| Storage Temperature | -40°C to 70°C |
| Humidity | 5% to 95% (Non-Condensing) |
| IP Grade | IP65 Outdoor Waterproof |
| Max Power Consumption | < 5W |
| Function | Firewall |
| Supports WPS | No |
| Supports WDS | No |
| Support Mesh | Not Supported |
| Certification | CE, FCC ID: 2AX9H-25126, RoHS |
8. User Tips
- PC IP Configuration: When accessing the web management interface, remember to set a static IP address for your PC (e.g., 192.168.1.10) and revert it to its original settings after configuration to ensure normal internet access.
- Optimal Performance: Adjust WiFi protocol and bandwidth settings in the WEB UI to optimize network speed and transmission distance for your specific environment.
- Line of Sight: For the best signal strength and stability, ensure there are no obstacles (trees, walls, buildings) between the two bridge units.
- Channel Selection: If you cannot find a WiFi signal, check and adjust the country region and WiFi channel settings in the WEB UI, as supported channels vary by region.
- Power Connection: Always ensure the product's WAN or POE port is correctly connected to the POE port of the adapter for proper power supply.
9. Warranty and Support
For any problems during use, please contact customer support. The installation of this device may require some network knowledge. If you are unable to install it, please reach out for assistance.
Customer Service
Email: support@kuwfi.com
Mobile/WhatsApp: +8618002530681
Manufacturer Information
Shenzhen HuaXuFeng Technology Development Co., LTD
Address: Room 1102, Youcheng Building, Minzhi Street, Longhua District, Shenzhen 518111, Mainland China
TEL: 86-0755-28010121
Certifications
This product is certified with CE, FCC ID: 2AX9H-25126, and RoHS compliance.

Additional Resources
A detailed User Manual in PDF format is available for download: View User Manual (PDF)