1. Introduction
This manual provides detailed instructions for the installation, operation, and troubleshooting of your new ANYFAR Wireless CarPlay Android Auto Interface. This device integrates seamlessly with your Audi's original MMI system, enabling advanced smartphone connectivity features such as Wireless CarPlay, Android Auto, MirrorLink, and AirPlay, while retaining original vehicle controls.
2. Safety Information
Please read and understand all safety instructions before installation and use. Improper installation or use can lead to damage to the product, vehicle, or personal injury.
- Ensure the vehicle's ignition is off and the battery is disconnected before beginning installation to prevent electrical shorts.
- If you are unsure about any part of the installation process, seek professional assistance.
- Do not obstruct airbags or other safety features during installation.
- Secure all cables and the interface module to prevent interference with vehicle operation or rattling noises.
- Operate the system responsibly and avoid distractions while driving.
3. Kit Contents
Verify that all components are present in your package:
- CarPlay Decoder Box
- Power Cable Harness
- LVDS Cable
- WiFi Antenna
- USB-AV Cable
- Gateway Cable
4. Setup and Installation
4.1. Compatible Models
This interface is compatible with various Audi models. Please verify your car's MMI system and screen size using the table below and the provided MMI version identification guide.
| Car Model | Years | Screen Inch |
|---|---|---|
| A4 | 2008-2016 | 6.5" / 7" |
| A5 | 2008-2016 | 6.5" / 7" |
| Q5 | 2010-2018 | 6.5" / 7" |
Note: Please contact support if you are unsure about your car's system compatibility.
4.2. Toggle Switch Setup (DIP Switches)
Locate the toggle (DIP) switches on the CarPlay decoder box. Adjust these switches according to your car's screen size to ensure proper display resolution.
4.3. Cable Connection Chart
Follow the wiring diagrams carefully for correct installation. The cables are designed for plug-and-play integration with your original system.
4.3.1. Transfer Gateway Connection
- A1/Q3 Transfer gateway from driver seat
- 10-11A6L Transfer gateway from passenger seat
- 10-15Q7 Transfer gateway from driver seat
- A4L/Q5 (HIGH) Transfer gateway from passenger seat
4.3.2. Transfer CAN from Air Condition Panel
- A8L/D4 Transfer CAN from air condition panel
- 12-15 A6L Transfer CAN from air condition panel
4.3.3. WiFi Antenna and USB-AV Cable Connection
4.4. Module Placement
The CarPlay interface decoder box should be installed in an appropriate space near or on the OEM head unit. Ensure it is secured and does not interfere with any moving parts or vehicle functions.
4.5. Switching Between Original MMI and CarPlay
After all cables are connected, you can switch between the original MMI3G interface and the CarPlay interface by long-pressing the "RETURN" button on your car's central console.
5. Operation
5.1. Functional Overview
The interface provides the following key functionalities:
- CarPlay / Android Auto: Seamless integration with iPhone (CarPlay) and Android phones (Android Auto) for navigation, music, calls, and voice control (Siri/Google Assistant). Supports both wired and wireless connections.
- Reversing Video Input: Smart module decodes video, allowing for rear-view camera input.
- Mirroring: Supports wired and wireless screen mirroring for both iPhone and Android phones.
- USB Video Playback: Automatic media playback from a USB disk for video and audio content.
5.2. Wireless CarPlay Connection Method
- On your iPhone, go to Settings > Bluetooth.
- Check for a Bluetooth device name starting with "CAR-xxxx" and select it.
- Turn on WiFi and keep it on. Return to Bluetooth to connect CarPlay.
- Select the Bluetooth device name (e.g., "CAR-BT-533d") and confirm pairing. A request window will pop up; select "Use CarPlay".
5.3. Apple Wireless Screen Mirroring
- On the interface menu, select "AirPlay".
- On your iPhone, connect to the device's WiFi network (e.g., "CAR-WIFI-XXX"). The password is typically 66668888.
- After successful WiFi connection, return to your iPhone's main interface, open the Control Center (shortcut menu), select "Screen Mirroring", and turn it on.
- From the list of devices, select "AirPlay" to complete the wireless screen mirroring.
5.4. Wireless Android Auto Connection Method
- On your Android phone, go to Settings > Bluetooth.
- Check for a Bluetooth device name starting with "CAR-xxx" and click on it.
- A pairing request will pop up; click "Pairing".
- After successful Bluetooth pairing, follow the Android Auto connection process on your phone screen. The system will connect automatically.
5.5. Android Wireless Screen Mirroring
- On the interface menu, switch the WIFI Auto Link to "ON" in the Settings page.
- On your Android phone, scan the QR code provided in the Auto Link app or download the Auto Link app from your browser.
- Open the Auto Link software, search for "CAR-WIFI-XXXX" and connect. Then click "START NOW" on the phone prompt box.
- The media sound for AutoLink will need to connect with Bluetooth.
6. Audio Settings
To adjust audio settings and resolve echo issues, follow these steps:
6.1. Call Echo Cancellation
If you experience echo during phone calls:
- Navigate to Settings > Audio > AEC Delay.
- Click the "Start Auto AEC" button. This will generate a beep.
- While correcting the echo, ensure the car is quiet.
- Set the volume to a moderate position.
- Click "Start Auto AEC" again.
- Wait 20 seconds for the estimation to complete.
7. Troubleshooting
- No Sound/Audio Issues:
- Ensure your car's original MMI system is set to AUX as the audio source.
- Check the audio settings within the interface for correct volume levels.
- If using an external audio output, ensure it is correctly selected on the original MMI.
- Phone Call Issues (No Sound/Microphone):
- Activate the vehicle's Bluetooth mode in the original MMI settings for call sound to work.
- Ensure the mic out cable is bridged with the mic in cable in the unit's wiring during installation to use the car's microphone.
- Verify phone call settings are enabled within the interface.
- Disconnections or Crashes (iPhone/Android):
- Ensure stable WiFi and Bluetooth connections.
- Check for any available firmware updates for the interface module.
- Restart both your phone and the car's infotainment system.
- Difficulty with Installation:
- Refer to online tutorials or videos for step-by-step guidance if the provided diagrams are unclear.
- Double-check all cable connections according to the diagrams.
8. User Tips
- DIY Installation: Many users successfully install this module themselves, saving significant costs compared to professional installation. A second pair of hands can be helpful.
- Plug and Play: The system is largely plug-and-play, requiring no cutting of original wires.
- Future Upgrades: The supplied cables are often pre-wired for parking sensors and reversing cameras, making future additions easier.
- Seamless Integration: The interface maintains original steering wheel controls and the car's microphone.
- Module Placement: Secure the module properly to prevent rattling noises while driving. Consider using a socket wrench for glovebox screws if hiding the unit there.
- Performance: The hardware is generally fast and responsive, with easy switching between screens.
9. Specifications
| Feature | Detail |
|---|---|
| Brand Name | ANYFAR |
| Origin | Mainland China |
| High-concerned chemical | None |
| Package Length | 26 cm |
| Package Width | 19 cm |
| Package Height | 13 cm |
| Package Weight | 1.063 kg |
| Processing Time | 7 days |
10. Warranty and Support
For detailed warranty information and further support, please refer to the official product documentation. A comprehensive user manual in PDF format is available for download, which may contain additional diagrams and troubleshooting steps.
You can access the PDF user manual here.
When contacting support, please be prepared to provide the following information:
- Your order ID
- Car model and year
- Screen size of your car's MMI system
- Current toggle switch setup
- Pictures of your LVDS cable connection
- The software version of the CarPlay decoder (found in the CarPlay decoder menu under Settings > System Version)