HORACO HC-SWTGW218AS

Contents

HORACO 2.5GbE Managed Switch User Manual

Model: HC-SWTGW218AS

HORACO 2.5GbE Managed Switch with 8 RJ45 ports and 1 SFP+ port

HORACO 2.5GbE Managed Switch with 8x 2.5G RJ45 ports and 1x 10G SFP+ uplink port.

1. Introduction

1.1 Foreword

This manual is designed for installers and system administrators responsible for network installation, configuration, and maintenance. It assumes the user has a foundational understanding of network communication, management protocols, technical terms, and practical skills related to networking devices.

1.2 Manual Convention

Throughout this manual, specific conventions are used to highlight important information:

  • Interpretation: Describes operations and provides necessary information.
  • Notice: Reminds the user of cautions. Improper operations may result in data loss or equipment damage.

2. Safety Information

Please read and understand all safety instructions before installing or operating the device. Keep this manual for future reference.

  • Ensure the power supply matches the device's requirements (DC 12V 1A).
  • Do not expose the device to water or excessive humidity.
  • Avoid placing the device in areas with high temperatures or direct sunlight.
  • Ensure proper ventilation to prevent overheating. The fanless design relies on ambient airflow for cooling.
  • Do not open the device casing; doing so may void the warranty and expose you to electrical hazards.
  • Use only the provided power adapter or a compatible replacement.
Fanless heat sink design of the switch

The switch features a fanless heat sink design for silent operation and efficient heat dissipation.

3. Package Contents

Verify that your package contains the following items:

  • HORACO 2.5GbE Managed Switch (Model HC-SWTGW218AS)
  • Power Adapter (EU Adapter, other adapters may be included based on region)
  • User Manual (PDF version available online)

If any items are missing or damaged, please contact your vendor.

4. Setup and Physical Installation

4.1 Physical Installation

The switch is designed to be compact and can be placed on a desktop or mounted in a network cabinet.

  • Placement: Choose a stable, flat surface. Ensure adequate space around the switch for airflow.
  • Power Connection: Connect the provided DC 12V 1A power adapter to the switch's power input and then to a power outlet.
  • Network Connections:
    • Connect your network devices (computers, servers, other switches) to the 2.5G RJ45 ports using Ethernet cables.
    • For high-speed uplinks or fiber connections, insert a compatible 10G SFP+ module into the SFP+ slot and connect the appropriate fiber or copper cable.
Dimensions of the HORACO 2.5GbE Managed Switch

The switch measures 160mm (length) x 90mm (width) x 35mm (height).

Switch installed in a network cabinet

Example of the switch installed in a network cabinet.

Switch installed in a network box

Example of the switch installed in a network box.

5. Web Page Login

To access the web management interface for configuration, follow these steps:

  1. Connect your PC: Ensure your computer is connected to one of the switch's RJ45 ports.
  2. Configure PC IP: Set your PC's IP address to be in the same network segment as the switch but with a different IP address. For example, if the switch's default IP is 192.168.2.1, set your PC's IP to 192.168.2.x (where x is between 2 and 254, not 1) and the subnet mask to 255.255.255.0.
  3. Open Browser: Open a web browser (e.g., Chrome 23.0+, Firefox 20.0+, or IE 9.0+).
  4. Enter IP Address: Type the default switch IP address http://192.168.2.1 into the browser's address bar and press "Enter".
  5. Login: A login window will appear.
    • Default Username: admin
    • Default Password: admin
    Click "Log in" to access the switch system.
Web Network Management Interface showing VLAN, Port Mirroring, Port Aggregate, and DHCP Snooping settings

The web management interface provides access to various network configuration options.

6. Operating Instructions (Web Management)

The web management interface allows you to configure and monitor various aspects of the switch. The navigation bar on the left provides access to different menu items, each with submenus for specific settings.

6.1 Home: Device Information

The "Home" section displays basic system information, including device name, model, IP address, MAC address, system uptime, and firmware version.

Web UI showing Device Info and Port Status

Device Information and Port Status as seen in the web interface.

6.2 Switch Monitor

This section provides real-time monitoring of the switch's performance and status.

6.2.1 MAC Address Table

Displays the MAC address table, which is dynamically updated. Entries are aged out if not refreshed. Proper aging time is crucial for switch performance.

6.2.2 Port Statistics

View statistics for each port, including link status, transmitted/received packets, and bytes.

Web UI Port Status table showing link status, duplex status, negotiation speed, and flow control

Example of Port Status table in the web interface.

6.3 Switch Configuration

This section allows detailed configuration of the switch's ports and features.

6.3.1 Port Setting

Configure individual Ethernet ports. You can enable/disable ports, set speed/duplex modes (10M/Half, 10M/Full, 100M/Half, 100M/Full, 1000M/Full, 2500M/Full), and enable/disable flow control.

6.3.2 Port Mirror

Copies traffic from a source port to a destination port for network monitoring and troubleshooting. Supports Rx, Tx, and Both directions.

6.3.3 Port Isolation

Separates message traffic between specified ports to prevent broadcast, multicast, or unicast floods.

6.3.4 Port Rate Limit

Restricts the transmission and reception rate on physical interfaces. Configurable for inbound (ingress) and outbound (egress) traffic.

6.3.5 Port Aggregate (LAG/LACP)

Bundles multiple physical interfaces into a single logical interface (Eth-Trunk) to increase bandwidth and reliability. Supports both static mode and LACP (Link Aggregation Control Protocol) mode.

  • Static Mode: Manual configuration of Eth-Trunk. All active links share traffic.
  • LACP Mode: Dynamic aggregation/disaggregation of links based on IEEE 802.3ad. Provides redundant backup and uninterrupted data transmission.

6.3.6 Static MAC

Manually configure static MAC address entries that do not age out.

6.4 VLAN Configuration

VLANs (Virtual Local Area Networks) segment a physical LAN into logical networks, improving broadcast domain management and security. The switch supports 802.1Q VLANs.

6.4.1 VLAN Setting

Configure VLAN IDs (1-4094) and names.

6.4.2 Port VLAN

Assign ports to VLANs, setting port types (Access, Trunk) and PVID (Port VLAN ID) for native VLANs.

6.5 Loop Configuration

Manages network loops to prevent broadcast storms and ensure network stability.

6.5.1 Loop Protocol

Enables loop detection packets to identify and alert about network loops. Options include Off, Loop Detection, and Spanning Tree.

6.5.2 STP Global / STP Port

Configures Spanning Tree Protocol (STP) or Rapid Spanning Tree Protocol (RSTP) globally and per port to eliminate physical loops in the data link layer.

6.6 QoS Configuration

Quality of Service (QoS) allows prioritizing network traffic to ensure performance for critical applications by managing bandwidth, delay, and packet loss.

6.6.1 Port to Queue

Sets processing priorities for different tags of data frames (e.g., 802.1p priority, DSCP).

6.6.2 Queue Weight

Configures the weight for queues, determining how traffic is prioritized (strict priority or weighted cyclic scheduling).

6.7 Advanced Settings

6.7.1 DHCP Snooping

Records user IP addresses and MAC addresses, and prevents unauthorized DHCP servers by dividing ports into Trust and Untrust ports.

Diagram illustrating DHCP Snooping networking

Typical Networking of DHCP Snooping.

6.7.2 Storm Control

Prevents network storms caused by excessive broadcast, unknown multicast, or unknown unicast messages by suppressing them based on configured packet rates.

6.7.3 IGMP Snooping

Manages and controls multicast groups on Layer 2 devices by analyzing IGMP messages and mapping ports to MAC multicast addresses.

6.7.4 Jumbo Frame

Configures the Maximum Transmission Unit (MTU) of the ports to support larger Ethernet frames, which can improve network efficiency for certain applications.

6.8 System Management

This section covers general device management functions.

6.8.1 IP Setting

Change the management IP address of the switch.

6.8.2 User Management

Modify the username and password for accessing the web management interface.

6.8.3 Device Reboot

Restart the switch.

6.8.4 Save Configuration

Important: Always save your configuration after making changes to ensure they persist after a reboot.

6.8.5 Backup Configuration

Backup the current configuration to a file for restoration if needed.

6.8.6 Firmware Upgrade

Upgrade the switch's firmware. Ensure you use the correct firmware version for your model. Do not power off the device during the upgrade process.

Firmware compatibility table for HORACO Switches

Firmware compatibility table. Ensure to use the correct firmware version (e.g., V200.2.4 for HC-SWTGW218AS).

6.8.7 Restore Factory

Restore the switch to its default factory settings.

7. Maintenance

  • Regular Cleaning: Keep the switch clean and free of dust. Use a soft, dry cloth.
  • Firmware Updates: Periodically check for new firmware versions on the official HORACO website to ensure optimal performance and security.
  • Configuration Backup: Regularly back up your switch configuration, especially before major changes or firmware upgrades.
  • Environmental Control: Ensure the operating environment remains within specified temperature and humidity ranges to prolong the device's lifespan.

8. Troubleshooting

8.1 Common Issues and Solutions

  • Cannot access Web UI:
    • Verify your PC's IP address is in the same subnet as the switch (e.g., 192.168.2.x for switch IP 192.168.2.1).
    • Ensure the Ethernet cable is securely connected.
    • Try a different browser or clear browser cache.
    • If the IP address was changed, try the new IP. If forgotten, a factory reset might be necessary.
  • No network connectivity:
    • Check link status LEDs on the switch and connected devices.
    • Verify cable integrity.
    • Check port settings (speed/duplex) in the web UI. Ensure they match connected devices or are set to Auto-negotiation.
    • If VLANs are configured, ensure devices are in the correct VLANs or that trunk ports are properly set up.
  • Slow network speed:
    • Check port statistics for errors or high utilization.
    • Ensure connected devices support 2.5GbE or 10GbE speeds.
    • Verify cable quality (Cat5e or higher for 2.5G, Cat6a or higher for 10G over copper).
    • Check for network loops (refer to Loop Configuration).
    • Review QoS settings if traffic prioritization is enabled.
  • Configuration lost after reboot:
    • Always click "Save Configuration" in the System Management section after making changes.
Screenshot of a network switch dashboard showing port status and traffic statistics

A network switch dashboard can help monitor port status and traffic.

iperf3 command line output showing network bandwidth test results

iperf3 is a useful tool for testing network bandwidth and identifying performance issues.

9. User Tips

  • Save Configuration: Always remember to save your configuration changes in the System Management section, otherwise, they will be lost after a reboot.
  • Firmware Updates: Users have reported successful firmware upgrades to V200.2.4. Ensure you download the correct firmware for your model from the official source.
  • Power Adapter: If you need a replacement power adapter, look for a 12V 1A adapter with a 5.5 * 2.1mm barrel connector. Note that some regional plugs might come with an adapter.
  • Web UI: The web interface is generally easy to use, though some minor typos may be present. It offers comprehensive features for a managed switch.
  • Performance: The switch runs cool and performs well, delivering expected 2.5GbE and 10GbE speeds.
  • VLANs and Link Aggregation: These advanced features are confirmed to work effectively, providing robust network management options.
  • RJ45 Shielding: Note that the RJ45 ports are not shielded.

10. Specifications

Feature Description
Brand Name HORACO
Model Number HC-SWTGW218AS
Switch Type Gigabit Switch
Ports 8*2.5G RJ45 ports, 1*10G SFP+ ports
Transmission Rate 10/100Mbps/1G/2.5G/10Gbps (2000 Mbps Full Duplex)
Switch Capacity 60Gbps
Communication Mode Full-Duplex & Half-Duplex
MAC Address Table 4K
Forwarding Mode Store and forward
Network Protocol IEEE802.3, IEEE802.3u, IEEE802.3x, IEEE802.3ab, IEEE802.3bz
Function LACP, VLAN Support
VLAN No (Refers to no hardware VLAN, but web-managed VLAN is supported)
Input Voltage DC 12V 1A
Power Consumption ≤12W
Working Environment Temperature: 0-40°C; Humidity: 10%-90%, non-condensing
Storage Environment Temperature: -40-70°C; Humidity: 5%-95%, non-condensing
Certification CE, FCC, RoHS
Package Dimensions 20cm x 15cm x 8cm
Package Weight 0.528 kg

11. Warranty and Support

For detailed warranty information and technical support, please refer to the official HORACO website or contact your vendor.

A comprehensive user manual in PDF format is available for download:

View User Manual (PDF)

This PDF document provides additional in-depth information regarding the switch's features and configuration.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.