diymore GBAA0158-001

Contents

Diymore Stepper Motor Controller Instruction Manual

Model: GBAA0158-001

1. Introduction

This document provides comprehensive instructions for the Diymore Stepper Motor Controller. This module is designed to generate control signals for stepper motor drivers, enabling precise control over stepper motor speed and direction. It supports both 12V and 24V power supplies, making it versatile for various stepper motor drive requirements.

Key features include:

  • Supports 12V/24V power supply.
  • Enables forward/reverse control for complex scenarios.
  • Integrated speed control module for precise motor speed adjustment.
  • Outputs stable and fast-response PWM pulse signals.
  • Comprehensive functionality suitable for various automation control applications.
Front view of the 12V/24V Stepper Motor Driver

Figure 1: Front view of the 12V/24V Stepper Motor Driver, highlighting its power supply compatibility.

2. Specifications

ParameterValue
Brand Namediymore
Model NumberStepper Motor Controller (GBAA0158-001)
Motor TypeStepper Motor
Power Supply12V / 24V
OriginMainland China
CertificationNONE
Dimensions (L x W x H)62mm x 35mm x 12mm (2.45in x 1.39in x 0.46in)

Frequency Options

The controller offers three low-frequency signal options, selectable via jumper settings:

  • High Frequency: 5.4 kHz to 160 kHz
  • Medium Frequency: 540 Hz to 16.6 kHz
  • Low Frequency: 80 Hz to 2.4 kHz

It can generate pulse signals or PWM signals, also selectable via jumper settings.

Dimensions of the stepper motor controller

Figure 2: Dimensions of the stepper motor controller: 62mm (2.45in) length, 35mm (1.39in) width, and 12mm (0.46in) height.

3. Setup

This module functions as a pulse generator for a stepper motor driver. A separate stepper motor driver must be installed to control the stepper motor. The basic control platform consists of this simple controller + stepper motor driver + stepper motor + DC power supply.

Connection Terminals

The board features terminals for VIN, GND, CLK, DIR, and EN. Note that different stepper drivers may use different labels for these signals:

  • EN: ENA (Enable) / FREE (Free)
  • PUL: PULS (Pulse) / CLK (Clock pulse)
  • DIR: CW (Clockwise) / CWW (Counter-clockwise direction)
Top-down view of the controller board with an overlay showing a common anode wiring diagram

Figure 3: Top-down view of the controller board with an overlay showing a common anode wiring diagram. This image also shows the labels for VIN, GND, CLK, DIR, EN terminals.

Common Anode Connection Method (A)

For drivers configured for common anode connection:

  • Connect EN+, PUL+, DIR+ from the driver to the common anode terminal.
  • Connect EN- from the driver to the EN terminal on the controller.
  • Connect PUL- from the driver to the CLK terminal on the controller.
  • Connect DIR- from the driver to the DIR terminal on the controller.
Detailed diagram illustrating the Common Anode Connection Method (A)

Figure 4: Detailed diagram illustrating the Common Anode Connection Method (A) for connecting the controller to a stepper motor driver.

Common Cathode Connection Method (B)

For drivers configured for common cathode connection:

  • Connect EN-, PUL-, DIR- from the driver to the common cathode terminal.
  • Connect EN+ from the driver to the EN terminal on the controller.
  • Connect PUL+ from the driver to the CLK terminal on the controller.
  • Connect DIR+ from the driver to the DIR terminal on the controller.
Controller board with text describing measurement frequency and connection methods

Figure 5: Controller board with text describing measurement frequency and connection methods (Common Anode and Common Cathode). It also lists alternative labels for EN, PUL, and DIR.

4. Operation

The module integrates a speed control function for precise adjustment of motor operating speed. Use the onboard potentiometer (knob) to adjust the output pulse frequency, thereby controlling the stepper motor's speed.

Angled view of the integrated speed control module

Figure 6: Angled view of the integrated speed control module, emphasizing its precise adjustment capability.

Frequency Selection

Adjust the jumpers on the board to select the desired frequency range (high, medium, or low) for the pulse signals. Refer to the 'Specifications' section for the exact frequency ranges.

Signal Type Selection

Use the appropriate jumper settings to select between generating pulse signals or PWM signals, depending on your application's requirements.

Forward/Reverse Control

The module supports forward and reverse rotation control. Utilize the dedicated direction control input (DIR) on the board to switch the motor's rotation direction.

5. Maintenance

To ensure the longevity and optimal performance of your stepper motor controller:

  • Keep the module clean and free from dust and debris.
  • Avoid exposing the module to excessive moisture or extreme temperatures.
  • Ensure all connections are secure and properly insulated to prevent short circuits.
  • Handle the board with care to avoid bending or damaging components, especially jumper pins.

6. Troubleshooting

  • Motor not responding: Verify all wiring connections are correct according to the common anode or common cathode method. Ensure the stepper motor driver is properly powered and connected.
  • Incorrect motor movement: Check the DIR signal connection. Ensure the frequency settings are appropriate for your stepper motor and driver.
  • No pulse output: Confirm the power supply (12V/24V) is correctly connected and providing stable voltage. Check jumper settings for pulse/PWM signal selection.
  • Labels on board are in Chinese: Refer to the 'Setup' section of this manual for English equivalents of common terminal labels (EN, PUL, DIR).
  • Bent jumper pins: Carefully straighten any bent jumper pins using fine-nose pliers if they are preventing proper connection.

7. User Tips

  • Remember a separate driver is needed: This module is a controller for a stepper motor *driver*, not a standalone motor controller. You will still need a stepper motor driver to interface with your motor.
  • Great for testing: This unit is highly effective for testing the axes of DIY milling machines or similar projects, saving the effort of building a custom control circuit.
  • Check physical condition upon arrival: While generally well-packaged, occasionally jumper pins might be bent during transit. Inspect the board carefully upon receipt.

8. Frequently Asked Questions (FAQ)

Q: What is the rated maximum continuous amperage?
A: The provided specifications indicate support for 12V/24V power supplies but do not specify a maximum continuous amperage for the controller itself. The current handling capability will primarily depend on the stepper motor driver it is paired with.

9. Warranty and Support

For any issues, questions, or support regarding your Diymore Stepper Motor Controller, please contact the seller or manufacturer directly. Ensure you provide your product model number (GBAA0158-001) and a detailed description of the issue for efficient assistance.

A user manual in PDF format may also be available for download from the seller's product page for additional reference.

© 2024 Diymore. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.