Ezonetronics RW-PCD026-L

Contents

Ezonetronics 5" Touch Screen Motorcycle CarPlay Screen User Manual

Model: RW-PCD026-L

Ezonetronics 5-inch Motorcycle CarPlay Screen with water droplets, showing CarPlay interface, dual cameras, and mounting bracket.

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Ezonetronics 5" Touch Screen Motorcycle CarPlay Screen. This device offers wireless CarPlay and Android Auto functionality, dual camera recording, and an IP67 waterproof rating, enhancing your riding experience with navigation, music, and safety features.

Important Safety Information

  • Ensure all wiring connections are secure and correctly polarized to prevent damage to the device or your motorcycle's electrical system.
  • Do not connect the smart screen's power wire (Red ACC+12V) to a power supply greater than 12V, as this will burn out the smart screen.
  • Avoid using a high-pressure water gun to rinse the screen, cameras, or tire pressure monitor, as this may cause damage despite the IP67 rating.
  • Always prioritize safe riding practices. Do not operate the device in a way that distracts you from the road.

Package Contents

Verify that all items are present in your package:

  • Ezonetronics 5" Touch Screen Display Unit
  • Dual Front and Rear Cameras (1080P)
  • Mounting Bracket and Accessories (for 12-28 cm handlebars)
  • Power Wiring Harness
  • Tools (Wrench, Hex Keys, Screwdriver)
  • User Manual (PDF available online)
Diagram showing the dimensions of the 5-inch screen, mounting bracket, wiring harness, and included tools.

Specifications

Feature Detail
Screen Size 5 inches
Display Type HD Touch Screen
Connectivity Wireless CarPlay, Android Auto, Bluetooth
Camera Resolution 1080P Dual Front and Rear Cameras
Waterproof Rating IP67 (fully dustproof, shrugs off rain and splashes)
Recording Loop-Cycle Recording (TF/SD Card support)
Power Supply Motorcycle ACC+12V (recommended)
Dimensions (Screen) 137mm x 80mm
Comparison image showing the product's HD 5-inch screen with reduced bezels versus a general screen.

Installation Guide

1. Mounting the Bracket

  1. Twist the ball head onto the back clip of the display unit until tightened.
  2. Use the variable diameter handle set to attach the bracket to your motorcycle's handlebars. This set supports 12-28 cm original handlebars.
  3. Install the main display unit onto the bracket. Adjust its position according to your vehicle model for optimal viewing, then tighten all screws to secure the installation.
User image showing the screen mounted on a motorcycle handlebar. User image showing the screen mounted on a motorcycle handlebar, displaying the Android Auto interface. User image showing the screen mounted on a motorcycle handlebar, displaying a map.

2. Wiring Diagram (Power & Cameras)

Follow the diagram and precautions carefully for electrical connections:

  • Power Wire (Red ACC+12V): Connect to your motorcycle's ACC+12V. Do NOT connect to the battery's constant power (B+) if you want the screen to turn off with ignition.
  • Negative Wire (Black): Connect to the negative terminal of your motorcycle's battery.
  • Cameras: Connect the front and rear cameras to their respective waterproof cable connectors on the main unit.
Detailed wiring diagram for the motorcycle CarPlay screen, showing connections for front and rear cameras, power (red to ACC+12V, black to negative battery terminal), and the main screen unit. Diagram showing dual high-definition front and rear cameras with 140-degree view angles, capturing road ahead and behind.

3. Optional TPMS Installation (Tire Pressure Monitoring System)

If you have purchased the optional TPMS sensors:

  1. On the screen, navigate to the Tire Pressure settings.
  2. Set the desired tire pressure unit (Bar or Psi) and alarm values. The screen will display a red warning if pressure is too low or too high.
  3. Pair the sensors: 'A' corresponds to the front wheel, 'B' to the rear wheel. Install the 'A' sensor on the front wheel and activate it, then install and activate the 'B' sensor on the rear wheel.

Note: If the tire pressure value is not displayed, please pair again. If replacing a sensor, unpair the old one before pairing the new sensor.

Diagram illustrating the installation of a tire pressure sensor on a motorcycle wheel and its pairing with the display unit.

Initial Setup

1. Powering On/Off

Once correctly wired, the device should power on with your motorcycle's ignition (if connected to ACC+12V). It features a fast boot time, ready to navigate in approximately 3 seconds.

2. Connecting to Mobile Phone (CarPlay/Android Auto)

  1. On the display, tap on the CarPlay or Android Auto icon, then select "WiFi Video".
  2. Scan the QR code displayed on the screen to download the companion APP to your mobile phone.
  3. Turn on the WiFi on your phone and connect to the display's WiFi network. The default password is 12345678.
  4. After a successful connection, your mobile phone's screen will be mirrored on the display, enabling CarPlay or Android Auto.

Note: Android phones can download videos to local storage, while Apple phones can only download to iCloud.

User image showing the screen displaying a multi-widget interface, likely for CarPlay or Android Auto.

3. Bluetooth Audio Setup

Bluetooth earphones and helmets connect to your mobile phone, not directly to the smart screen. After enabling CarPlay or Android Auto via the screen's Bluetooth, ensure your phone is connected to your Bluetooth earphones or helmet. This routes audio from your phone through your Bluetooth device.

Diagram illustrating Bluetooth pairing: phone connects to screen, then phone connects to helmet/headset for audio output.

Operation

1. Driving Recorder Operation

The driving recorder interface provides the following functions:

  • Recording Time: Displays the current recording duration.
  • Homepage: Returns to the main screen.
  • Video Playback: Access recorded videos.
  • Stop/Start Recording: Toggles recording on or off.
  • Swap Recordings: Switches between front and rear camera views during recording.
  • Take a Photo: Captures a still image.
Image showing the screen displaying a road view, with a filmstrip graphic indicating continuous loop-cycle recording.

2. Replay Interface Functions

When reviewing recorded footage, the replay interface offers:

  • Video Playback
  • Video Recording (from playback)
  • Function Settings
  • Homepage
  • Unlocked Video/Photo
  • Locked Video
  • Photo
  • Play/Pause
  • Lock a Video
  • Full Screen
  • Switch between Front and Rear Screen Recording
  • Checklist
  • Delete the Checklist

3. Online Navigation & Music

Utilize CarPlay or Android Auto for online navigation with the latest maps and enjoy online music playback directly on the screen.

Image of the screen displaying a navigation map on a motorcycle, highlighting online navigation capabilities. Image of the screen displaying a music player interface, indicating support for online music.

Maintenance

  • Clean the screen and camera lenses regularly with a soft, damp cloth. Avoid abrasive cleaners.
  • Ensure all cable connections remain tight and free from corrosion.
  • Periodically check the mounting bracket for security, especially after riding on rough terrain.
  • The device is IP67 waterproof, meaning it is protected against dust and temporary immersion in water. However, avoid prolonged submersion or high-pressure water jets.
Image of the screen being splashed with water, demonstrating its IP67 waterproof capability. Comparison image showing the screen in a desert environment and submerged in water, reinforcing its durability and waterproof nature.

Troubleshooting

  • Screen does not turn on: Check power connections. Ensure the red wire is connected to ACC+12V and the black wire to the negative terminal. Verify your motorcycle's battery is charged.
  • Screen does not turn off with ignition: This indicates the red power wire is connected to a constant power source (B+) instead of ACC+12V. Re-wire to ACC+12V if automatic shut-off is desired.
  • Tire pressure not displayed: Re-pair the TPMS sensors as per the installation guide. If replacing a sensor, ensure the old one is unpaired first.
  • Unstable USB power supply: It is recommended to connect the device directly to the motorcycle's ACC+ (12V) for stable power.
  • Difficulty connecting CarPlay/Android Auto: Ensure your phone's WiFi is on and connected to the device's WiFi network (password: 12345678). Restart both the device and your phone if issues persist.

User Tips

  • The 5-inch screen size is generally considered optimal for motorcycles, providing necessary information without obstructing view.
  • The device supports a wide range of languages, including Japanese, for broader accessibility.
  • The image quality of the front and rear cameras is clear, providing good recording for safety and documentation.
  • When mounting, ensure the plastic clamp is sufficiently tightened to prevent movement on bumpy roads. Consider alternative mounting solutions if stability is an issue.
  • For night riding, a brightness modulator for the screen could enhance visibility, though the display is generally visible in daylight.

Warranty and Support

For detailed warranty information and further technical support, please refer to the official user manual PDF available online. This document contains comprehensive guides and contact information for customer service.

A PDF version of the user manual is available for download: View User Manual (PDF)

© 2024 Ezonetronics. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.