KEVANLY Round LED Tail Light Strobe Warning Light User Manual

1. Introduction

This manual provides essential information for the safe and effective installation, operation, and maintenance of your KEVANLY Round LED Tail Light Strobe Warning Light. This product is designed to be installed on vehicle side or rear, providing enhanced visibility and safety through its multi-functional lighting capabilities.

2. Safety & Warnings

Important Safety Information

• Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
• Keep the device and its cord out of reach of children under 3 years old.
• Keep away from children unless supervised by an adult.
• Do not use this product for purposes other than its intended use.
• Inspect the product before each use; do not use if damaged.
• Follow installation and operation guidelines to avoid injury.
• Do not expose to water or moisture (for electrical products).
• Handle with care to avoid cuts or injuries (for sharp/dangerous items).

Compliance Information: This product complies with LVD 2014/35/EU standards. This product must comply with all applicable safety and regulatory requirements in the market where it is sold. Sellers must assess which requirements and regulations apply based on the actual product type, function, and destination market.

3. Specifications

Diagram showing product dimensions (approx. 14.50cm/5.71inch width, 14.70cm/5.80inch height, 5.00cm/1.97inch depth) and key specifications.

The light features IP67 waterproofing, adapting to various weather conditions.

4. Installation

Applicable Range

Modifications for tire lug nuts on all types of motorcycles and scooters. Can be installed on both the car body and the rear of the car.

Installation Steps

1. Before installation, ensure the tire lug nut is clean, free of oil residue, and dry.
2. Screw the warning light clockwise onto the tire lug nut, ensuring a secure fit to prevent loosening from driving vibrations.
3. Test the sensor function by lightly tapping the light body: a slight vibration should activate the light, which will automatically turn off after a few seconds of inactivity—indicating normal operation.

Wiring Method

• Black wire: Negative ground
• Red wire: Connects to the brake light
• White wire: Connects to the reverse light
• Green wire: Connects to the driving lights

Detailed wiring diagram showing color-coded wires and their corresponding functions.

Examples of the light installed on the side and rear of a truck.

5. Operation

Usage Instructions

• The light automatically illuminates during vehicle vibration.
• It powers off when the vehicle is stationary after a few seconds of inactivity.
• No manual operation is required for basic functionality.

Light Show Modes

The light features various modes for enhanced visibility and signaling:

• Yellow Light: For turn signals.
• Brake Flash: Flashes when brakes are applied.
• Reverse White Light: Illuminates when reversing.
• Vehicle Traffic Flow: Dynamic flowing light for warning.

Visual representation of the light's different modes: yellow for turn, brake flash, reverse white, and dynamic traffic flow.

6. Charging

• When the built-in rechargeable lithium battery is depleted, connect the included charging cable to a standard USB port.
• The indicator light on the device will remain on during charging.
• The indicator light will turn off automatically when the battery is fully charged.
• After charging, disconnect the cable and securely replace the dust cap over the charging port to maintain the waterproof seal.

7. Maintenance

Precautions

• Before installation/removal, jack up the vehicle to lift the tires off the ground to prevent tipping during operation.
• Before driving, check the lamp's secure mounting and periodically tighten it to prevent detachment during high-speed travel.
• Avoid contact with strong acids/alkalis or sharp objects to prevent shell damage that could compromise waterproofing.
• Do not disassemble the lamp yourself to avoid damaging internal sensors and batteries.

Heat Dissipation

The light features an alloy lamp body with a metal backplane for faster cooling, allowing it to operate normally in environments from -40°C to 80°C.

8. Troubleshooting

If you encounter issues with your KEVANLY Round LED Tail Light, please consider the following:

• Light not activating: Ensure the battery is charged. Check for secure mounting and sufficient vibration to trigger the sensor.
• Intermittent operation: Verify all wiring connections are secure and free from corrosion. Ensure the dust cap is properly sealed after charging to prevent moisture ingress.
• Physical damage: If the shell is damaged, the waterproofing may be compromised. Avoid contact with harsh chemicals or sharp objects.
• Disassembly: Do not attempt to disassemble the light. Unauthorized disassembly will void the warranty and may cause further damage.

9. User Tips

To maximize the performance and lifespan of your LED Tail Light:

• Regularly check the tightness of the light's mounting, especially after driving on rough terrain or at high speeds.
• Keep the charging port clean and ensure the dust cap is always securely in place when not charging.
• For optimal visibility, ensure the light's surface is clean from dirt and debris.

10. Warranty & Support

Disassembly of the product by unauthorized personnel will void the warranty.

For further assistance or detailed information, please refer to the official user manual PDF available at: User Manual (PDF).

Manufacturer: Guangzhou Kejie Trading Co., Room 302, No. 10, Ou Gang North Street, Ke Mu Long West Road, Tianhe District, Guangzhou City, Guangdong Province, China.

EU Authorized Representative: SUCCESS COURIER SL, Calle de RIO TORMES 13A, oficina 1, Fuenlabrada, Madrid, 28947 Spain.