HITBOX ARC200E

Contents

HITBOX ARC200E 3-in-1 Welder User Manual

Model: ARC200E

1. Safety Information

WARNING: Welding is dangerous and can cause harm to you and others. Always protect yourself when welding. Refer to the Operator Safety Guide for Compliance with Manufacturer Accident Prevention Requirements for more information.

Important Safety Considerations:

  • Professional Training: Operation requires professional training. Use labor protection welding supplies authorized by the state security department. The operator must have a valid "Metal Welding (OFC) Operation" certificate.
  • Power Disconnection: Always cut off power before maintenance or repair.
  • Electrical Shock: Never touch a charged area with bare skin or wet gloves/clothing. Ensure insulation from the ground and workpiece. Confirm your work location is safe.
  • Fumes and Gases: Keep your head away from smoke and gases. Use exhaust or ventilation equipment to ensure a well-ventilated working environment.
  • Fire and Explosion: Welding sparks can cause fires. Ensure no combustible materials are nearby. Have fire extinguishers readily available and know how to use them. Container welding is strictly prohibited. Do not use for powder spray thawing.
  • High Temperature Workpieces: Avoid direct contact with hot workpieces. Allow the torch to cool during continuous use.
  • Pacemakers: Individuals with pacemakers should stay away from the solder joint area and consult medical attention.
  • Moving Parts: Keep hands, hair, and tools away from moving parts like fans. Ensure all doors, panels, and lids are closed during operation.
  • Machine Failure: If difficulties arise during installation or operation, consult this manual. If issues persist, contact your supplier's service center.
Diagram illustrating safety features of the HITBOX ARC200E welder, including electrical protection, VRD, overload protection, and IP21S water rating.
Figure 1: Safe & Reliable Features (Electrical Protection, VRD, Overload, IP21S Water Rating)

2. General Instructions

The HITBOX ARC200E supports MMA, Gasless MIG, and Lift TIG welding. It features an IGBT power supply unit with a unique control mode for enhanced reliability and a high duty cycle for extended welding times. The closed-loop feedback control ensures stable operation within 15% of the supply voltage.

Adjustable welding voltage and current provide excellent welding characteristics. The MIG mode offers a stable arc, minimal spatter, beautiful beads, and high welding efficiency, including tip ball removal, high no-load voltage, slow wire feeding, and high arc-triggering success rate.

For MMA welding, the machine provides stable current and excellent arc initiation, suitable for various electrodes. The high switching frequency significantly reduces the size and weight of the machine, improves welding efficiency, and saves energy by reducing magnetic and resistance losses. Noise pollution is virtually eliminated as the switching frequency is beyond the audio range.

Image showing three welding processes: Stick, Lift TIG, and Flux MIG, highlighting the 3-in-1 capability of the welder.
Figure 2: Three Welding Modes (Stick, Lift TIG, Flux MIG)

3. Product Overview and Panel Description

The ARC200E features a user-friendly interface with a large LED display for clear operation data.

Front and back panel diagram of the HITBOX ARC200E welder with numbered components.
Figure 3: Front and Rear Panel Components

Front Panel Components:

  1. Current Display
  2. 0.8/1.0 Indication (for wire diameter)
  3. Spool Gun Mode Indicator
  4. MMA Mode Indicator
  5. LIFT-TIG Mode Indicator
  6. MMA Function Setting Area
  7. "+" Output Terminal (Positive)
  8. Abnormal Indication
  9. Function Switching Button
  10. Mode Switching Button
  11. Current Control Knob
  12. "-" Output Terminal (Negative)
  13. Spool Gun Torch Switch
Close-up of the large LED display on the ARC200E welder, showing welding parameters like current, rod diameter, Hot Start, Arc Force, Antisticking, and VRD.
Figure 4: Large LED Display for Welding Parameters

Rear Panel Components:

  1. Power Cord Input
  2. Power Switch

4. Technical Specifications

Parameter ARC200E (110V/220V) ARC200E (220V Only)
Input Voltage (V) AC 110/220V ± 15%, 50/60Hz AC 220V ± 15%, 50/60Hz
Rated Input Current (A) AC 110V 40A, AC 220V 35A AC 220V 35A
Rated Input Capacity (KVA) 110V 4.5, 220V 7.7 7.7
Recommended Fuse Capacity (A) 110V 40A, 220V 35A 35A
MMA Weld Current Range (A) 110V 20~120, 220V 20~160 20~160
MIG Welding Current Range (A) 110V 35~120, 220V 20~160 35~160
MIG Voltage Range (V) 110V 15.4~18.5, 220V 15.4~20.4 15.4~20.4
No-load Voltage (V) 81 81
Wire Feeding Speed Range (m/min) 1.5~14 1.5~14
Applicable Wire Diameter (mm) 0.8/1.0 0.8/1.0
Rated Duty Cycle 60% (from JSON) / 35% at 25°C (from PDF) 60% (from JSON) / 35% at 25°C (from PDF)
Efficiency 0.8 0.8
Power Factor 0.75 0.75
Protection Class IP21S IP21S
Insulation Class F F
Dimensions (L x W x H) 35x16x25cm 35x16x25cm
Weight (Machine) 4.31 kg (9.44 lbs) 4.31 kg (9.44 lbs)
Weight (Packaging) 6.1 kg 6.1 kg
Certification CE CE

Welding Capabilities:

  • MMA Welding Rod: 1.6-4.0mm
  • MIG Welding Wire: 0.8/1.0mm
  • TIG Tungsten Needle: 1.6-2.4mm
  • Welding Thickness (MMA): 2-10mm
  • Welding Thickness (MIG): 1-8mm
  • Welding Thickness (TIG): 1-4mm
  • Welding Materials: Carbon Steel, Iron, Galvanized Sheet, Stainless Steel
Image showing the dimensions of the HITBOX ARC200E welder (13.58in length, 6.3in width, 8.66in height) and its weight (9.44lbs).
Figure 5: Welder Dimensions and Weight

5. Setup and Installation

Note: Always turn off the power switch before any electrical or electronic connection. This machine has an IP21S protection rating; avoid using it in the rain.

5.1 Connection of Input Cables

  1. Connect the main power cable to the rated input power supply. Grounding connections are required for safety.
  2. Ensure the primary cable is tightly connected to the correct socket to prevent oxidation.
  3. Verify the input voltage with a multimeter to ensure it is within an acceptable range.

5.2 MMA (Stick) Installation

  1. Plug the quick plug of the electrode holder cable into the appropriate socket on the front panel and tighten clockwise. For DCEP (Direct Current Electrode Positive), connect the electrode holder to the "+" output terminal and the work fixture to the "-" output terminal. For DCEN (Direct Current Electrode Negative), connect the electrode holder to the "-" output and the work fixture to the "+" output.
  2. Plug the quick plug of the earth clamp cable into the remaining socket on the front panel and tighten clockwise.
  3. If using long secondary cables (welded and grounded), choose cables with a larger cross-section to minimize voltage drop.
Diagram showing MMA, Lift TIG, and Gasless MIG welding setups.
Figure 6: MMA, Lift TIG, and Gasless MIG Welding Setups

5.3 MIG (Gasless Flux Core) Installation

  1. Connect the main power cable to the rated input power supply. Grounding connections are required for safety.
  2. Plug the quick plug on the wire feeder into the "+" socket on the front panel of the welder and tighten clockwise.
  3. Plug the cable with the work clip (earth clamp) into the "-" socket on the front panel of the welder and tighten clockwise.
  4. Install the spool gun and mount the wire spool onto the rotating shaft. Ensure the groove dimensions on the drive roller match the contact tip size of the torch and the wire diameter.
  5. Insert the aviation plug of the wire feeder into the aviation socket on the front panel of the machine.
  6. Press the wire snap button to feed the wire out of the torch head.
  7. Connect the wire feeder to the flow regulator on the cylinder with a tubing (if using gas, though this model supports gasless MIG).
Image showing a welder performing Flux MIG welding with a spool gun.
Figure 7: Flux MIG Welding Setup (Spool Gun required)

5.4 LIFT TIG Installation

  1. Insert the earth clamp cable plug into the "+" socket on the front panel of the welder and tighten clockwise.
  2. Insert the TIG 17V torch cable plug (not included, requires extra purchase) into the "-" socket on the front panel of the welder and tighten clockwise.
  3. Connect the air inlet of the TIG17V torch to an argon cylinder.
  4. Ground the power supply.
Diagrams illustrating different welding setups: Stick 6011/7018, Stick 6010/6013, Lift TIG, and Flux MIG.
Figure 8: Various Welding Mode Setups

6. Operating Instructions

6.1 General Operation

  1. After completing the installation, turn on the power switch on the back panel. The power LED will illuminate, and the fan will start.
  2. Select the desired welding mode (MMA/MIG/TIG) using the mode switch.
  3. Adjust the welding current and voltage using the control knobs based on the workpiece thickness and welding requirements.

6.2 MMA (Stick) Welding Operation

  1. Switch the mode to MMA.
  2. Adjust the welding current with the current control knob. General guidelines for welding current based on electrode diameter:
    • φ2.5mm: 70-100A
    • φ3.2mm: 110-160A
    • φ4.0mm: 170-220A
    • φ5.0mm: 230-280A
  3. The ARC200E features adjustable Hot Start and Arc Force for improved arc initiation and stability. It also has an automatic anti-sticking function to prevent electrode sticking.
Welder performing stick welding, showing a smooth weld seam. Text highlights 'Ideal Performance' with various welding rod types.
Figure 9: Ideal Performance for Stick Welding (6010/6011/6013/7018 rods)

6.3 MIG (Gasless Flux Core) Welding Operation

  1. Switch the mode to MIG.
  2. Pay attention to polarity: for Gasless MIG, the ground clamp is typically connected to the positive terminal.
  3. Start the wire spool gun switch to feed the wire until it extends about 1cm from the nozzle.
  4. Touch the wire to the workpiece, then press and hold the switch to start welding. Release the switch to stop welding.
  5. Adjust the inductance control knob: counter-clockwise for lower inductance and harder arcs; clockwise for higher inductance and softer arcs. A harder arc is generally selected at lower current, and a softer arc at higher current.
  6. Select appropriate welding voltage and current using the control knobs.

6.4 LIFT TIG Welding Operation

  1. Switch the mode to LIFT TIG.
  2. Pay attention to polarity: users can choose different tungsten needle operation based on the workpiece and welding wire.
  3. After installation, turn on the power switch. The power indicator light will be on and the fan will work.
  4. Rotate the wire feeding knob of the TIG welding gun. After the wire touches the workpiece, start welding. Lift the torch to initiate the arc, then stop welding by breaking the arc.

6.5 Welding Speed, Elongation, and Gas Flow

  • Welding Speed: Combine welding quality and productivity. Increased speed weakens protective effects and speeds cooling, which can affect weld molding. Too slow a speed can burn through the workpiece. Aim for a welding speed not exceeding 50cm/min.
  • Elongation (Stickout): Increased elongation can boost productivity but may lead to excessive spattering, wire breakage, and unstable welding. Generally, the extension should be about 10 times the electrode diameter.
  • Protective Gas Flow: For FCAW (Flux-Cored Arc Welding), less or no shielding gas is required. Refer to specific values for gas flow rate if using gas.
Image showing a welder with text 'Adjustable Hot Start & Arc Force' and a diagram of a weld bead.
Figure 10: Adjustable Hot Start & Arc Force for Improved Weld Quality

7. Maintenance

WARNING: Maintenance operations require sufficient electrical expertise and comprehensive safety knowledge. Only qualified operators should perform these tasks. Always ensure the machine's input cable is disconnected from power before any maintenance.

7.1 Work Environment

  • Perform welding in a dry environment with humidity below 90%.
  • Operating temperature should be between -10°C and 40°C.
  • Avoid welding in open air unless protected from light and rain. Keep the machine dry and away from wet ground or puddles.
  • Avoid welding in dusty areas or environments with aggressive chemical gases.
  • Shielded arc welding should be performed in an environment with adequate airflow.

7.2 Ventilation

The machine generates strong welding current and requires effective cooling. The built-in fan is crucial for stable operation. Ensure the air vents are open and unblocked. Maintain a minimum distance of 30 cm between the machine and nearby objects for proper ventilation, which is essential for performance and service life.

7.3 Overvoltage Protection

The machine uses automatic voltage compensation to maintain the voltage within its specified range. Exceeding the input voltage can damage internal components.

7.4 Overload Protection

Observe the maximum load current and duty cycle. Do not exceed the maximum load current, as this can shorten the machine's service life and cause damage.

7.5 Overtemperature Protection

If the machine overheats due to overload, the overheating LED on the front panel will illuminate, and welding may stop. Do not restart immediately. Allow the built-in fan to cool the machine. Welding can resume once the internal temperature drops and the overheating LED turns off.

7.6 General Maintenance Procedures

  1. Periodically check internal circuit connections, especially plugs. Tighten loose connections. If oxidation is present, remove it with sandpaper and reconnect.
  2. Keep hands, hair, and tools away from moving parts such as fans to prevent injury or damage.
  3. Regularly clean dust with dry, compressed air. If welding in a smoky or polluted environment, clean the machine daily.
  4. Ensure the compressed air is at an appropriate temperature to avoid damaging small internal parts.
  5. Avoid rain, water, and vapor infiltration. If exposed, dry the machine thoroughly and check insulation before reuse.
  6. Periodically check the insulation cover of all cables for wear and tear. Repair or replace as needed.
  7. Regularly check the trachea (gas hose) for good condition. Replace if cracks are found.
  8. If storing the machine for a long time, place it in a dry environment in its original packaging.

8. Troubleshooting

This section provides common failure analysis and solutions. For complex issues, contact customer support.

Symptom / Error Code Nature of Failure Solution
The overheating LED is on. Overheating due to excessive welding current/time or fan malfunction. 1. Check welding current and time; operate as per manual. 2. Check fan operation; ensure power supply to fan is 230V. 3. If thermal switch is damaged, replace it.
No response when pressing gun trigger, protection LED is off. Trigger malfunction, poor connection, or wire feeder issue. 1. Check if power LED and digital meter are lit. 2. Check torch trigger and connection. 3. Ensure wire feeder is well connected.
Wire feeder sends wire, but no output current, protection LED off. Poor contact, loose plug, damaged torch, or internal control failure. 1. Check power cord contact to workpiece. 2. Ensure quick plug is correctly connected. 3. Check wire feeder connection. 4. Inspect welding torch for damage. 5. Internal control of PCB PK-94 may have failed.
Output current when pressing trigger, but wire feeder does not send wire. Wire feeder blockage/damage, torch contact issues, or wire feed plate fault. 1. Inspect wire feeder for blockage/damage. 2. Inspect welding torch contacts for blockage/damage. 3. Wire feed plate PK-93 may be faulty.
Welding can be performed, but voltage cannot be adjusted; no-load voltage too high. Control cable or control PCB failure. 1. Check control cable of wire feeder. 2. Control PCB inside machine may have failed.
Welding current is unstable. Incorrect pressure arm, wrong drive roller, worn contact tip, poor wire quality, twisted cable, or loose plug. 1. Check pressure arm on wire feeder. 2. Ensure drive roller matches wire size. 3. Check/replace contact tip. 4. Verify welding wire quality. 5. Check if torch cable is twisted. 6. Check if quick plug is loose.
The weld is not well protected. Premature torch removal or insufficient protective gas afterflow. 1. Do not remove torch immediately after welding; allow protective gas to shield beads. 2. Extend protective gas afterflow time. Contact company if issue persists.
There is a large pit after welding. Incorrect operating mode for crater welding. 1. Select 4T mode for crater welding at low currents. 2. Change operating mode.
ERR CODE E1 Overcurrent fault. Send to a specialized service point for overhaul.
ERR CODE E2 Overloaded. 1. Reduce welding current/time, keep power on no-load operation. 2. Replace damaged fan. 3. Clean excessive dust inside machine.
ERR CODE E3 Overload and overcurrent. Refer to troubleshooting for overload.
ERR CODE E4 Low grid voltage. Check power supply voltage. Increase cross-sectional area of power line if too small or long.

9. User Tips

No specific user tips were available from provided reviews or Q&A content.

10. Warranty and Support

HITBOX welders are built from high-quality components and undergo rigorous testing. If you have any questions or concerns regarding your product, please feel free to contact HITBOX for support.

For further information, you may refer to the official user manual PDF: User Manual (PDF).

You can also visit the official website: www.hitboxweld.com.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.