XTOOL INPLUS IP919 Pro

Contents

XTOOL INPLUS IP919 Pro Smart Diagnostic Tool User Manual

Comprehensive Guide for Setup, Operation, and Maintenance

1. Introduction

The XTOOL IP919 Pro Diagnostic Tool interfaces with the electronic control unit (ECU) of a vehicle to retrieve diagnostic trouble codes (DTCs), access data stream information, and command active tests (bi-directional control tests). Various vehicle control systems, such as engine, transmission, anti-lock brake system (ABS), SRS (Airbag) system, Chassis, and Body, are readily diagnosed using this tool. The Diagnostic Tool is capable of graphing up to eight (8) live data parameters on a single screen and features diagnostic topology mapping.

Experience enhanced diagnostics with the XTOOL IP919PRO. Equipped with a 2.2GHz+1.8GHz Octa-core processor, 8GB RAM, 128GB storage, and a 10.1-inch touchscreen, it offers swift operation and seamless multitasking. Additional features include a collapsible kickstand, built-in speaker and microphone, rear camera, and a 6400mAh 7.2V battery for extended use.

It supports full system diagnostics, full OBD II functions, activation tests, coding, vehicle-specific functions under each vehicle's software, ADAS calibration, ECU configurations, VAG guided functions, PMI, Online Programming (Benz BMW VW), BMW Test Plan, and 51 special functions outside the Diagnostics.

XTOOL INPLUS IP919 Pro device and VCI box
Figure 1: XTOOL INPLUS IP919 Pro Diagnostic Tool and VCI Box
XTOOL INPLUS IP919 Pro highlighting hardware specifications and diagnostic protocols
Figure 2: Key Features and Hardware Specifications

2. Safety Information

For your safety, the safety of others, and to prevent damage to devices and vehicles, it is crucial to read and understand all safety instructions presented in this manual before operating or coming into contact with the device.

General Safety Instructions:

  • Read and Understand: Ensure that all operators and individuals in the vicinity of the device have read and understood the safety instructions.
  • Proper Use: Only use the device as described in this manual. Always adhere to the safety messages and test procedures provided by the vehicle or equipment manufacturer.
  • Knowledge and Skill: The automotive technician must be knowledgeable about the system being tested. Familiarize yourself with proper service methods and test procedures.
  • Acceptable Testing Practices: Perform tests in a manner that ensures your safety, the safety of others, and prevents damage to the device and the vehicle.

Specific Responsibilities:

  • Refer to Manufacturer Guidelines: Always consult and follow the safety messages and applicable test procedures from the vehicle or equipment manufacturer before using the device.
  • Use Appropriate Tools and Techniques: Due to the variety of test applications and product variations, it's important to use the correct tools and techniques for each specific task.
  • Anticipate Safety Requirements: While this manual provides comprehensive guidance, it cannot cover every potential situation. Technicians must be prepared to handle unforeseen circumstances safely.

By adhering to these guidelines and responsibilities, you can ensure a safe and effective working environment while using the device.

Safety Messages

Safety messages are included to prevent both personal injury and damage to equipment. Each safety message begins with a signal word that indicates the level of hazard involved.

⚠️ Danger

This signal word "indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to the operator or to bystanders."

⚠️ Warning

This signal word "indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to the operator or to bystanders."

Safety Instructions

  • Safe Environment: Always perform automotive testing in a safe environment.
  • Eye Protection: Wear safety eye protection that meets ANSI standards.
  • Avoid Hazards: Keep clothing, hair, hands, tools, and test equipment away from all moving or hot engine parts.
  • Ventilation: Operate the vehicle in a well-ventilated work area to avoid inhaling poisonous exhaust gases.
  • Transmission and Brakes: Put the transmission in PARK (for automatic) or NEUTRAL (for manual) and ensure the parking brake is engaged.
  • Wheel Blocks: Place blocks in front of the drive wheels and never leave the vehicle unattended while testing.
  • Ignition System Caution: Be extra cautious around the ignition coil, distributor cap, ignition wires, and spark plugs, as these components generate hazardous voltages when the engine is running.
  • Fire Extinguisher: Keep a fire extinguisher suitable for gasoline, chemical, and electrical fires nearby.
  • Test Equipment Connections: Do not connect or disconnect any test equipment while the ignition is on or the engine is running.
  • Clean Equipment: Keep the test equipment dry, clean, and free from oil, water, or grease. Use a mild detergent on a clean cloth to clean the outside of the equipment as necessary.
  • No Driving While Testing: Do not drive the vehicle and operate the test equipment simultaneously to avoid distractions that may cause an accident.
  • Service Manual Reference: Refer to the service manual for the vehicle being serviced and adhere to all diagnostic procedures and precautions. Failure to do so may result in personal injury or damage to the test equipment.
  • Battery Check: Ensure the vehicle battery is fully charged and the connection to the vehicle DLC is clean and secure to avoid damaging the test equipment or generating false data.
  • Avoid Electromagnetic Interference: Do not place the test device on the vehicle's distributor, as strong electromagnetic interference can damage the device.

3. Setup

3.1 What's In The Box

The XTOOL INPLUS IP919 Pro package includes the following items:

Name QTY
Tablet1
VCI Box1
Type-C to Type-A Data Adapter1
Type-C to Type-B Data Cable1
Type-C to Type-C Charger Cable1
Type-C to PD-12V Charging Cable1
PD Supply Charger US1
Cigar Lighter Cable1
Charger Adapter EU1
Charger Adapter UK1
DB15 Main Cable1
OBD II-161
HONDA-31
BMW-201
BENZ-141
BENZ-381
TOYOTA-171
MAZDA-17R1
KIA-201
HYUNDAI/KIA-101
NISSAN-141
GM/DAEWOO-121
UNIVERSAL-31
SUZUKI-31
FIAT-31
CITROEN-21
AUDI-41
MITSUBISHI-12+161
Wireless Charger Dock1
Color Carton1
Quick Start Guide1
Packing List1
Tool Case1
XTOOL IP919 Pro and accessories in a hard case
Figure 3: XTOOL INPLUS IP919 Pro and Accessories in Hard Case
Close-up of various cables and adapters included in the kit
Figure 4: Included Cables and Adapters

3.2 Main Ports of The Tablet

The tablet features several ports for connectivity and power:

  • Type-C Port: For data transfer and charging.
  • Reset Hole: To reset the device if unresponsive.
  • Power Button: To turn the device on/off.
  • Microphone: For audio input.
  • Charging Contact: For use with the charging dock.
  • Camera: For taking pictures.
  • Nameplate: Contains product information.
  • Speaker: For audio output.

3.3 Main Ports of The VCI Box

The VCI Box connects to the vehicle and communicates wirelessly with the tablet:

  • Screen: Displays status information.
  • DB15 Port: For connecting the main cable.
  • Nameplate: Contains product information.
  • USB Type-B Port: For wired connection.
  • DC Port: For power input.

3.4 Power Sources and Charging

The XTOOL IP919 Pro Diagnostic Tool can receive power from its internal battery pack, an AC power supply, or the charging dock.

  • Internal Battery Pack: The internal rechargeable battery provides approximately 3.5 hours of continuous operation when fully charged.
  • AC Power Supply: Connect the provided AC power supply to a standard AC outlet and plug it into the DC power supply input jack on the Diagnostic Tool. Use only the supplied AC power supply.
  • Charging Dock: The included charging dock can also charge the tablet. Place the tablet on the dock. The indicator light will be red when the battery is low, blue during charging, and green when fully charged.
Video 1: XTOOL IP919 Pro Product Demonstration, showing charging and basic operations.

3.5 Turning On/Off

  • Turning On: Press and hold the power button (top right) for approximately five seconds. The tool will power on automatically if sufficiently charged or connected to AC power. If the battery is completely drained, charge for more than 6 hours before turning on.
  • Turning Off: Press and hold the power button for more than three seconds. The tool will automatically power off.
  • Emergency Shutdown: If the Diagnostic Tool is unresponsive, press and hold the Power button for five seconds until it turns off. IMPORTANT: Forcing a shutdown during vehicle communication may cause issues with the ECM.

3.6 Product Activation

To activate your XTOOL IP919 Pro:

  1. Select a language for the operating system.
  2. Connect to an available Wi-Fi network.
  3. Click "Register" to enter the activation page. You can also use "TRAIL" mode, but activation is recommended for online software updates.
  4. After successful login, the Diagnostic Tool is registered and activated.

3.7 Vehicle Connection

To connect the Diagnostic Tool to a vehicle:

  1. Connect the DB15 connector of the main cable to the VCI box.
  2. Plug the OBDII-16 connector of the main cable into the vehicle's DLC port.
  3. Once the VCI box is powered on, the tablet will automatically search for it and establish a Wi-Fi connection.

NOTE: For models using DOIP (Diagnostic Over Internet Protocol), ensure a wired connection to the vehicle for reliable communication.

4. Operating Instructions

4.1 Diagnostic Screen Layout and Icons

When the Diagnostic Tool is turned on, the diagnostic program starts automatically, displaying the diagnostic screen. A hidden toolbar at the bottom of the tablet can be revealed by swiping up from the bottom of the screen for 3 seconds.

XTOOL IP919 Pro screen showing the main menu with various functions
Figure 5: Diagnostic Screen Main Menu

Key icons on the diagnostic screen include:

  • Auto Scan: Automatically detects VIN and scans all available vehicle electronic control modules.
  • Diagnostic: Accesses the diagnostic menu for Auto VIN detection, manual VIN input, DEMO program, and OBD-II tests.
  • Special Function: Provides access to commonly performed maintenance services.
  • Report: Includes functions for diagnostic reports, data playback, and data viewing.
  • Updates: Allows downloading of diagnostic software programs.
  • More: Accesses user account settings, workshop profile, subscription period, and firmware information.
  • Settings: Customizes language, units, USB mode, OS settings, volume, brightness, and device information.
  • Remote Control: Launches TeamViewer for remote assistance.
  • XTOOL: Provides contact information for support.

4.2 How to Diagnose Vehicles

The Diagnostic Tool enables communication with a vehicle's electronic control systems to retrieve DTCs, view PID data, conduct actuation tests, and perform advanced functions such as resets, relearns, matchings, adaptations, and initializations.

4.2.1 Vehicle Identification

To ensure proper communication, the vehicle must be correctly identified. Follow screen prompts to enter required information. Procedures may vary by make, model, and year.

  • Auto Scan: Clicks "Auto Scan" to automatically detect and decode the VIN. If Auto Scan fails, try other options.
  • Manual Selection: If Auto Scan or Manual Input fails, select "Manual Selection" to manually input vehicle information (make, model, year) for diagnostics.

IMPORTANT: Special Functions are not universally available for all vehicles. Compatibility must be verified using the vehicle's VIN, make, model, and year.

4.2.2 ECU Programming & Coding

The IP919PRO diagnostic tool includes lifetime free ECU programming functions for BMW, Mercedes, VW/Audi, Skoda, and Ford/Mazda users. This allows replacement of existing software/firmware, programming new ECUs, and fixing software-controlled performance and emission issues.

  • Online Coding: Directly accesses online vehicle repair data for high-level repairs (compatible with BMW ONLY).
  • Offline Coding: Reads code from the original module and writes it to the new module (compatible with VW/Audi/Skoda/Benz/Mitsubishi, etc.).
  • ECU Configuration: Refreshes hidden functions to reprogram adaptive data, activates higher-level car functions, and disables annoying features (e.g., seat belt buzzer, remote window control).

Note: Coding functions vary by model. Check compatibility by sending VIN to XTOOL support.

ECU Programming and Coding features
Figure 6: ECU Programming and Coding Capabilities
Advanced ECU Coding & Programming details
Figure 7: Advanced ECU Coding & Programming

4.2.3 Topology Mapping

The XTOOL InPlus IP919PRO diagnostic tablet offers Module Topology Mapping for quick issue identification. It provides advanced fault code analysis, access to detailed data, repair tips, and real-world repair cases, all verified by professionals. It also gives a clear view of the vehicle's data bus for efficient diagnostics.

Topology Mapping diagram
Figure 8: Diagnostic Topology Map Display

4.2.4 IMMO Reset (Key Programming)

The XTOOL IP919PRO car scanner provides comprehensive IMMO reset functions, including:

  • Programming new key fobs
  • Reading PIN codes
  • Adding smart keys
  • Remote learning
  • All key lost recovery
  • Disabling lost vehicle keys

Note: The IMMO Reset function is not universally compatible, so it's important to confirm compatibility with XTOOL support before purchase.

IMMO Reset functions and expansion accessories
Figure 9: Key Programming Capability and Expansion Accessories

4.2.5 Bidirectional Control (Active Test)

The XTOOL InPlus IP919PRO bidirectional scanner allows you to send commands to the ECU, enabling it to perform specific tests or retrieve information from various vehicle modules. This feature helps you quickly identify faults in your car's subsystems, without needing to rely on the vehicle's control system.

Most-Used Active Tests include:

  • EVAP Test
  • Injector Buzz Test
  • Window/Mirror/Door Lock Test
  • A/C Clutch On/Off
  • ABS Pump Cycling
  • Pump and Value Tests
  • Interior & exterior lights Test
  • Sound horn Test
  • and more...
Bidirectional Control with active test examples
Figure 10: Full Bidirectional Control (14000+ Active Tests)

4.2.6 OE-Level All System Diagnostics

The XTOOL IP919PRO car diagnostic tool performs OE-Level diagnosis on all available systems like ABS, SRS, TPMS, Engine, Transmission, Brake System, etc., with complete capabilities for reading codes, clearing codes, reading live data, retrieving freeze frame, active test, and reading ECU information. This makes it an ideal choice for DIY auto mechanics and repair shops.

4.2.7 Auto Scan & CAN Fast Scan

After the device communicates with the car, it automatically reads the car VIN and information, detects the machine status, connects to CAN, and communicates faster.

4.2.8 51+ Service Functions

The IP919 Pro offers over 51 special functions, including Matching, Resets, Calibration, Initialization, and Adaptions for specific vehicles. Some key functions include:

  • Oil Reset: Reset service intervals after oil change and turn off the oil light.
  • EPB Reset: Reset brake pads after replacement of the brake system.
  • SAS Adjustment: Perform calibration of the steering angle sensor.
  • BMS Reset: Register the new battery to the ECU after replacement.
  • Throttle Relearn: Enables initial settings to throttle to adjust air intake.
  • ABS Bleeding: Cycle the ABS pump to bleed air out of the ABS system.
  • Injector Coding: Coding injectors after replacement.
  • Transmission Match: Reset adaptive shifting points in the automatic Transmission Control Unit.
  • Gear Learning: Crankshaft position sensor learns crankshaft tooth machining tolerance to diagnose engine misfires more accurately.
  • Other functions: Steering position sensor calibration, Zero Point Calibration, Hybrid Control Compression Test, HVAC Control Module Calibrate, Injector balance test, ECU Configuration, VGT Turbo Calibration, Idle Learn Reset, Alcohol Content Reset, ABS Initialization, Seat Weight Sensor Calibration, Fuel Trim Reset, Cylinder Power Balance, Crankshaft Sensors Relearn, Language change, A/F Settings, Stop/Start Reset, etc.

Note: ALL service functions available vary across vehicles. Please contact XTOOL support to check compatibility with your car's VIN.

Grid of 51+ reset functions
Figure 11: Overview of 51+ Reset Functions
42+ Service Functions list
Figure 12: Detailed List of Service Functions

4.2.9 Pre-scan and Post-scan & Diagnostic Report 2.0

  • Pre-scan: Records the vehicle's condition before repair and provides helpful reference data. It also helps confirm if the issue has been fixed and if the vehicle is back to normal after repair.
  • Post-scan: Ensures the repair is complete and done right, improving diagnostic accuracy and customer satisfaction. The upgraded Diagnostic Report 2.0 offers four report types, system icons, and a customizable layout with your shop's logo.
Pre-scan and Post-scan reports
Figure 13: Pre-scan and Post-scan Reports

4.2.10 8 IN 1 Live Data Graphing

The IP919PRO automotive scanner can display live data streams in text or graphs for various parameters like cylinder misfires data, transmission fluid/Oil temperature, fuel trim, ATF temperature, cylinder balance rates, engine rpm, O2 sensors, mass air flow sensor data, fuel pressure, actual fuel temperature vs desired fuel temperature, etc.

  • Export Live Data as CSV: Exporting live data as a CSV file allows tracking vehicle performance over time.
  • 8-In-1 Graphing: Customize specific PIDs and merge graphs for up to 8 data PIDs combined at one time in one graph.
  • Individual Graphing: Graph up to 8 sensors individually on the same screen.
8 IN 1 Live Data Graphing
Figure 14: 8-in-1 Live Data Graphing

4.2.11 OBD-II/EOBD Operations

This section covers the concept, protocols, test functions, and basic operation of the OBD-II/EOBD function. To find the OBD-II/EOBD function, go to Diagnostic > Region Selection > OBD-II.

Global OBD uses 5 communication protocols: J1850PWM, J1850VPW, ISO 9141-2, ISO 14230-4, and ISO 15765-4 (CAN).

The OBD-II function allows you to access "generic" OBD-II/EOBD data, which is limited to emission-related diagnostics such as:

  • Checking for emissions-related diagnostic trouble codes (DTCs).
  • Checking the cause of an illuminated malfunction indicator lamp (MIL).
  • Checking monitor status prior to emissions certification testing.

To access other available electronic control module (ECU) data for vehicle-specific systems, parameters, or enhanced diagnostics, use the "AUTO SCAN" or "Diagnostic" functions and enter all systems diagnostics or individual system diagnostics. The OBD-II function is used to access "generic" OBD-II/EOBD data for OBD-II/EOBD compliant vehicles that are not included in the all systems/individual systems diagnostics.

IMPORTANT: Generic OBD-II/EOBD data are not included in the engine system diagnostic data.

4.2.11.1 Read Trouble Code

The "Read Trouble Code" option displays a list of current emission-related DTCs, including Stored Codes (Generic Codes and Manufacturer-Specific Codes), Pending Codes, and Permanent Codes.

4.2.11.2 Clear Trouble Code (Mode $04)

This option is designed to erase all emission-related diagnostic data stored in the memory of the selected ECM. This includes Diagnostic Trouble Codes (DTCs), freeze frame data, and test results. When you select the clear codes function, a confirmation screen appears to prevent accidental data loss. You must choose "Yes" on the confirmation screen to proceed with the operation.

4.2.11.3 Live Data (Mode $01)

Use this function to view current emission-related data from the selected electronic control module (ECM) of the vehicle. The main screen layout consists of two primary columns: the left-hand column provides descriptions of each parameter, while the right-hand column displays the corresponding parameter values along with their units or states.

4.2.11.4 Read Freeze Frame (Mode $02)

Freeze frame data provides a snapshot of critical parameter values at the moment a diagnostic trouble code (DTC) is set. This function allows you to display freeze frame data for any stored emission-related DTC. Typically, the stored freeze frame data corresponds to the last DTC that occurred.

4.2.11.5 I/M Readiness (Smog Check)

This function is used to check the readiness of the monitoring system. It is an excellent function to use prior to having a vehicle inspected for compliance with a state emissions program. Selecting I/M Readiness opens a sub-menu with two choices: "Monitor status since DTCs cleared" and "Monitor status this driving cycle."

4.2.11.6 On-Board Monitor Test (Mode $06)

This function allows you to view the results of On-Board Monitor (OBM) tests. These tests are particularly useful after vehicle servicing or after erasing the vehicle's control module memory.

4.2.11.7 Read Vehicle Information (Mode $09)

The purpose of this function is to enable the Diagnostic Tool to request and display vehicle-specific information, such as the vehicle identification number (VIN), the calibration identification, and the calibration verification number (CVN), of the test vehicle.

4.2.12 Supported Protocols

The XTOOL INPLUS IP919 Pro supports advanced diagnostic protocols:

  • CAN FD & DOIP: Supports DOIP for newer vehicles utilizing the DOIP protocol. Diagnostics over DoIP enable much higher data rates than with CAN, saving time and expenses for complex diagnostic tasks and flash applications. Compatible with BMW (F&G chassis), Land Rover & Jaguar models (2017 later).
  • FCA protocol: Provides thorough safety certification for vehicle gateways, covering models from Jeep, Dodge, Chrysler, Porsche, Maserati, and Fiat manufactured after 2018.
200+ Brands, CAN FD & DOIP, FCA protocol
Figure 15: Protocol Support and Vehicle Coverage

5. Maintenance

5.1 Software Updates

This chapter details how the software subscription operates and outlines basic procedures for software updates.

  • The subscription is an annual fee that covers compatibility with all makes and models, rather than being tied to individual models or functions.
  • Upon expiration of the subscription, you have the option to renew it immediately or skip renewal for certain years until you are ready to update again. If you choose not to renew, the existing software programs remain on the Diagnostic Tool but cannot be updated to the latest versions.
  • Software updates can be performed while connected to a Wi-Fi network or using a mobile phone's hotspot. Using a mobile phone's hotspot is recommended in case of network provider restrictions or when home Wi-Fi is unavailable.

To update the software programs, you have 2 (two) options:

  1. Update All Software Programs: Update all by clicking "Update All" at the bottom right of the update menu.
  2. Update Individual Software Program: Update a specific software program by clicking the "↑" icon at the right side of the corresponding software program. If the update is interrupted, click the "↑" icon again to proceed.
XTOOL IP919 Pro screen displaying software updates
Figure 16: Software Updates Screen
XTOOL IP919 Pro screen displaying software updates with progress bars
Figure 17: Software Update Progress

5.2 Delete Software Program

If the diagnostic tablet has taken up too much memory and become slow, you can delete rarely used software programs to free up space.

To delete a diagnostic software program, click "Diagnostic" > Select Region > Press and hold the vehicle maker icon for 5 seconds to activate the job menu. Click "Delete" to delete the software program.

IMPORTANT: It's advisable not to delete software programs close to the subscription expiration date. Instead, re-download any deleted software programs before the subscription expires to ensure access to necessary software.

6. Troubleshooting (FAQ)

Q1: I haven't found I/M readiness in the menu.

A: Please enter Diagnostic > Select America/Europe/Asia > Click the "OBD-II" icon on the top left of the screen > Auto Scan/Select OBD-II Protocol > I/M Readiness.

Q2: Unable to find live sensor data as the generic OBD2 scanner, like short-term/long-term fuel trim.

A: Please enter Diagnosis > Select America/Europe/Asia > Click the "OBD-II" icon on the top left of the screen > Auto Scan/Select OBD-II Protocol > Live Data > LTFT, STFT or similar term.

Q3: Unable to find the misfire data for my Ford/Dodge/Chrysler/Jeep cars?

A: Please Select Diagnostic > America/Europe/Asia > OBD-II (On the top left of the screen) > Auto Scan or Select OBD-II Protocol for your car > On Board Monitor Test > Select "Misfire Cylinder Data" or similar term.

Q4: How to export live data as CSV files?

A: To generate CSV files: Live data > custom > Choose which live data you want to generate > Record > Save > Preview. To find the CSV files: Report > CSV View > Choose the live data you have saved just now.

Q5: I cannot charge the battery now. I plugged in the cord, it's not charging. The battery is almost dead, only about 10% left.

A:

  1. Try to use the original charging cable or OBD test cable to charge the device for more than six hours. (Using the original charging cable to connect the power supply with a stable 12V voltage is preferred).
  2. Hold down the shutdown button for 15 seconds and observe whether the device can be turned on normally. (Do not connect the charging cable).
  3. Connect the device to the computer through the USB cable to see if the device can be recognized by the computer.
  4. If neither of the above methods successfully charges the device, please contact our technical support: support@xtoolonline.com and send a video showing the charging issue.

Q6: Can scanner tune up car?

A: Sorry, IP919 Pro Diagnostic Tool does not have the capability to tune up car.

Q7: Can this scanner still be used once the 3 year free updates are finished?

A: Yes, of course, you can still use its last updated software when it expires, even when it expires after three years.

Q8: It was frozen until the battery went flat even I tried the reset button and the power button.

A: Please make sure you have updated the App to the latest version (To update the App to the latest, go to Settings > About > App > click the arrow at the right side to check the latest App version and update to the latest.). If yes, please reset to factory settings and check again. If it still does not work, please reach us directly via support@xtoolonline.com.

Q9: I cannot update, I've tried Wi-Fi and cell phone as hotspot, however, keep telling me failure connection.

A: This problem could reside with the setting of your router firewall or the network provider in your region that restricts access to the server, please check if your router firewall can access the server or not. If the problem still exists, please reach us directly via support@xtoolonline.com.

Q10: Any chance to install Google Play Store?

A: We are sorry that this diagnostic tool does not support installing Google Play Store. However, if you want to install a third-party app, you can download the APK file and install it on the diagnostic tool. We don't recommend installing other third-party apps as it may slow down its running speed.

Q11: Why should I connect the scanner to the internet once a month?

A: It's a government policy compliant requirement to connect the device to Wi-Fi once a month to report IP location to prevent the device from being used for illegal activities. If connecting it to Wi-Fi did not solve the issue, please reach us directly via support@xtoolonline.com ASAP.

Q12: The auto scan/VIN cannot work on my vehicle.

A: As for auto scan/VIN, it does not cover all vehicles as some vehicles did not store VIN in the ECU, some VIN is not included in our coverage database, and some vehicles like Dodge work in "sending command, answering command" mode for vehicle communication.

You can try below alternative navigation methods:

  • Turn on the ignition and not start the engine to try auto scan. For older vehicles, please turn on the ignition and start the engine and try auto scan.
  • Manual input VIN.
  • Diagnosis > America/Europe/Asia > Vehicle Selection > Automatic Detection.
  • Diagnosis > America/Europe/Asia > Vehicle Selection > Manually Selection.

Q13: My diagnostic tool cannot connect to Wi-Fi.

A: If it shows "times out", please check your router and make sure that your router selected WPA2, not WPA3 (maximum compatibility), and that it has not blocked the outgoing network traffic to non-US regions like China. Switching to mobile phone hotspot will most likely solve the registration issue. You can switch back to home Wi-Fi for software downloads when activation is done.

The second method is to connect to the Wi-Fi extender. If you have the Wi-Fi main modem and the extender, you can try to disconnect the diagnostic tool from the main Wi-Fi and connect it to the internet via the extender.

If it has connected to the internet but shows "connect internet to sync your device", the problem is that the country and time zone (China time zone) in the Android system didn't match what the network time zone was (Pacific time zone) and is preventing it from syncing. Please just correct the time zone to Pacific time zone by entering main screen > settings > System > Date & Time > "select time zone".

Q14: How can I change the menu language into Spanish?

A: To change the menu language, please send the S/N of the diagnostic tool to our support team via support@xtoolonline.com and get Spanish software program authorization. When the authorization is done, go to "Settings" on the diagnostic menu > language > Spanish to change the language of the Android tablet into Spanish, then go to "Updates" download all software programs. When all software programs in Spanish have been downloaded and installed, you may use the diagnostic tool in Spanish.

Q15: Why the scanner shows the report shared successfully but the email box didn't receive the report?

A: As all the reports are sent by our email: service@xtoolonline.com, the email may be blocked even if the device shows "send successfully". Since you use Gmail, you can follow instructions to whitelist our sending mailbox: service@xtoolonline.com. Refer to online guides for whitelisting emails in Gmail.

Q16: When you enter the diagnosis software program, it shows "license exception" or "Failed" error message.

A: Please try to delete the software programs by pressing and holding it and then re-download it again under the "Updates" to check whether this issue is solved or not. If not, please contact our support team via support@xtoolonline.com with the S/N of the diagnostic tool.

Q17: Browser can access internet normally, but cannot download the updates under "Updates", prompted to check the network connection in the Update.

A: Please switch to mobile hotspot or other Wi-Fi and try again.

Q18: When activating the device, it shows an error message "registration failure" after entering your email address.

A: Try mobile hotspot (recommended) or a different network to activate.

Q19: Received a used device with a lock screen password, unable to open the device.

A: Contact our support team with the device's S/N via support@xtoolonline.com to resolve the issue.

Q20: How to use the function of "Remote Control"?

A: The "Remote Control" menu is generally used when you need tech support from XTOOL. An appointment will be set with you at a suitable time for you and the engineers. You cannot start a remote control without an appointment.

Q21: What is the update fee of IP919 Pro? After my IP919 Pro passes the free subscription date, can I use it as usual as before?

A: The renewal fee of IP919 Pro after three years is $99 per year. IP919 Pro has a 3-year free update validity period. Three years later, the previously downloaded and updated software packages can still be used, but the latest software packages cannot be obtained if you don't pay the renewal fee. If you want to update the IP919 Pro after three years, fourth year, or fifth year, you can contact XTOOL to extend the period, which costs $99 per year. After subscription, you can get all the newest software.

Q22: How can I subscribe to the update on my IP919 Pro?

A: The update fee for the IP919 Pro is $99 per year. If you wish to subscribe, please proceed by transferring the payment directly to info@acartool.com via PayPal. Once the transfer is complete, kindly provide XTOOL via support@xtoolonline.com with a screenshot of the transaction. The update will be promptly added to your device within 24 hours.

Q23: I don't want to register an account. Why did I fail to perform the functions in trial mode?

A: Trial mode is not designed for vehicle coverage or compatibility checks. Its main purpose is to offer practice and help users become familiar with the functions and user interface of the diagnostic tool. Therefore, the function will be limited if you don't register a new account, so it is recommended that you register an account to use the tool on your vehicle, which will be more convenient.

Q24: When using the trial mode, do I need to connect my device to the Internet/Wi-Fi?

A: No, you don't need to connect your device to the Internet/Wi-Fi when you are in trial mode.

Q25: Shall I connect my device to the Internet/Wi-Fi all the time?

A: No, it doesn't need an Internet connection all the time. You just need to register it and download the updates with an internet connection. For some special vehicles like Peugeot, scan tools need to be connected to the Internet because it is required by the manufacturer. It will require an internet connection when you are doing some advanced features like ECU Programming.

Q26: Does your tool support all functions on all vehicles?

A: All XTOOL tools are comprehensive diagnostic tools that can work on many vehicle brands, but they cannot perform all functions on all vehicles, just like any other scan tools in the market. This is because not all vehicles come with the same functions when manufactured, and even vehicles of the same model might have various configurations.

Q27: Why, when I manually enter the VIN on my device, are the letters Q, I, O on the keyboard gray?

A: Because the three letters Q, I, and O are easily confused with other characters, such as the numbers 1 and 0. Therefore, VIN standards (including ISO and SAE standards and Chinese national standards) stipulate that these three characters cannot be used. It's normal that these three letters on the keyboard are gray. You can use the device normally.

Q28: How can I transfer the device's data to my phone or PC?

A: For phones: If it is iOS, the tablet does not support file transfers to iOS devices. If it is Android, please agree to receive the transfer on your phone after clicking Bluetooth transfer on the tablet. If your phone is Android and it still doesn't work after you tried the steps above, please kindly try connecting to a computer to transfer the files.

Here are the steps for your reference to transfer to PC:

  1. Connect the Diagnostic Tool to a PC by using a Type-C cable. Insert one end into the Type-C port on the Diagnostic Tool and the other end into a USB 2.0 port on the PC.
  2. Swipe down from either the upper right or upper left corner of the Diagnostic Tool to bring up the drop-down menu. Click on "Android System. Charging this device via USB".
  3. Change the option from "No data transfer" to "File Transfer".
  4. On the PC, check the connected devices and click on "IP919 Pro" to access and manage the files stored in the internal memory of the Diagnostic Tool.

7. Specifications

Item Description/Specification
Display10.1 Inch Touch Screen, 1920 x 1200 Resolution
Operating SystemAndroid 10.0
Processor2.2GHz+1.8GHz Octa-core Processor
Memory8G RAM, 128G ROM
ConnectivityBluetooth 5.0, Wi-Fi(2.4GHz & 5Ghz), Type-C
Operating MethodFlat Panel Touchscreen
Upgrade MethodDevice Connects to WIFI for Online Upgrade
Battery7.2V Rechargeable Li-ion Battery, 6400mAh
Tested Battery Life3.5 Hours
Power Supply Input100-240V~50-60Hz 0.5V Max
Power Supply Output5.0V-3.0A 15.0W/9.0V-2.22A, 19.98W/12.0V-1.67A 20.04W
Dimensions31.5*3.2*19(CM)
Free Renewal Update3 Years
Charging MethodType-C Charging (Fast Charging), Charge Dock
Supported ProtocolsCAN FD/DOIP/FCA
USB PortUSB2.0
WIFI2.4G/5Ghz
SensorGravity Accelerometer/Ambient Light Sensor
AudioMicrophone
SpeakerBuilt-In Speaker
Camera8 Mega Pixel
Weight (Including Battery)1.41 KG
Gross Weight8.3 KG
Operating Temp Range (Ambient)32°F ~ 104°F (0°C ~ 40°C)
Storage Temp (Ambient)14~122°F (-10~50°C)
Operating Humidity<90%

8. Warranty & Support

8.1 Limited Two-Year Warranty

Shenzhen XTOOLtech Intelligent Co., LTD. (the Company) warrants to the original retail purchaser of this XTOOL device that should this product or any part thereof during normal usage and under normal conditions be proven defective in material or workmanship that results in product failure within two years from the date of purchase, such defect(s) will be repaired, or replaced (with new or rebuilt parts) with Proof of Purchase, at the Company's option, without charge for parts or labor directly related to the defect(s).

The Company shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the device.

This warranty does not apply to:

  • Products subjected to abnormal use or conditions, accident, mishandling, neglect, unauthorized alteration, misuse, improper installation/repair or, improper storage;
  • Products whose mechanical serial number or electronic serial number has been removed, altered, or defaced;
  • Damage from exposure to excessive temperature or extreme environmental conditions;
  • Damage resulting from connection to, or use of any accessory or other product not approved or authorized by the Company;
  • Defects in appearance, cosmetic, decorative, or structural items such as framing and non-operating parts;
  • Products damaged from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft, or improper usage of any electrical source.

8.2 Contact Us

For technical assistance, wholesale inquiries, or to become a distributor:

9. User Tips

  • Language Authorization: The initial language is English. If you need to use other languages, send the serial number (on the back of the device) to XTOOL support for authorization.
  • Software Updates: The device comes with three years of free software updates. After this period, you can continue to use the last updated software, or renew the subscription for $99 per year to get the newest software.
  • Physical Features: The device includes a convenient kickstand on the back, which is appreciated by users for ease of use.
  • Performance: Users report the tablet is very fast (8GB RAM) and the software coverage, especially for European brands, is impressive.
  • Seller Responsiveness: The seller is noted for being very responsive and professional in addressing issues like transit damage.
  • Connectivity: For some advanced features like ECU Programming, an internet connection is required. Ensure your Wi-Fi settings (WPA2 compatibility) or mobile hotspot are configured correctly if you experience connection issues.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.