LiftMaster 878Max

Contents

878Max Wireless Keypad User Manual

For LiftMaster Garage Door Openers

1. Introduction

The 878Max Wireless Keypad provides convenient keyless entry to your garage. It is compatible with LiftMaster garage door openers manufactured from January 1, 1993, that utilize 315 MHz or 390 MHz frequencies and have a LEARN button. This manual provides detailed instructions for installation, programming, operation, and maintenance.

Video: Product overview and features of the 878Max Wireless Keypad.

2. Safety Information

WARNING:

  • This product can expose you to chemicals including lead. For more information, refer to www.P65Warnings.ca.gov.
  • To prevent serious injury or death from a moving gate or garage door:
  • Install the Wireless Keyless Entry within sight of the garage door, out of reach of children (minimum height of 5 feet / 1.5m), and away from all moving parts of the door.
  • Always keep remote controls out of reach of children. Never permit children to operate or play with remote controls.
  • Activate the gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
  • Always keep the gate or garage door in sight until completely closed. Never permit anyone to cross the path of a moving gate or door.

3. Setup and Installation

3.1. Before You Start

  • Read these instructions thoroughly before beginning.
  • If using with residential door openers, ensure the opener was manufactured after January 1, 1993, and uses photoelectric sensors.
  • The keypad will activate your door/gate during programming. Ensure the door area is clear of obstructions.
  • Start with the garage door closed.
  • Ensure the garage door opener light is working, as it acts as a programming indicator.
  • Install the battery and program the keypad prior to final installation.

3.2. Battery Installation

The 878Max keypad uses a 9V battery. Open the battery compartment cover located at the bottom of the keypad to insert the battery. Ensure correct polarity.

878Max Wireless Keypad with battery compartment open

Image: 878Max Wireless Keypad with battery compartment open, showing the 9V battery.

3.3. Mounting the Keypad

  1. Select a location to mount the keypad at a minimum height of 5 feet (1.5m), out of reach of children.
  2. Remove the battery cover and battery to access the mounting holes.
  3. Mark the top mounting hole and drill a 1/8" (3.2mm) pilot hole.
  4. Install the top screw, allowing 1/8" (3.2mm) to protrude. Position the keypad over this screw.
  5. Mark the bottom hole and drill a 1/8" (3.2mm) pilot hole. Install the bottom screw, being careful not to overtighten.
  6. Reinstall the battery and replace the cover.

3.4. Programming the Initial PIN

The keypad is pre-programmed for LiftMaster openers with a yellow LEARN button. Locate the LEARN button on your garage door opener (usually on the back or right side). Refer to the diagram below to identify your opener's LEARN button type.

Diagram showing different garage door opener LEARN button colors and frequencies

Image: Diagram illustrating different LEARN button colors (Red/Orange, Purple, Green, Yellow) and their corresponding frequencies (390 MHz, 315 MHz).

Method A: For Yellow LEARN Button (Security+ 2.0)

  1. Press and release the LEARN button on the garage door opener. The LEARN LED will light.
  2. Enter a 4-digit personal identification number (PIN) of your choice.
  3. Press the ENTER button until the opener light bulb blinks or two clicks are heard.
  4. Test by entering the programmed PIN and then pressing the ENTER button. The garage door opener will activate.

Method B: For Yellow LEARN/Security+ 2.0 and Other LEARN Buttons (Purple, Red/Orange, Green)

  1. Press and hold the '*' and '#' buttons on the keypad until the lights stop blinking.
  2. Enter a 4-digit personal identification number (PIN) of your choice. Press the '#' button.
  3. Press and release the ENTER button the number of times that corresponds with your garage door opener type:
# of PressesGarage Door Opener Type
1Yellow LEARN Button (Security+ 2.0)
2Purple LEARN Button (315 MHz Security+)
3Red/Orange LEARN Button (390 MHz Security+)
4Green LEARN (390 MHz Billion Code)
  1. Press and release the '0' button.
  2. Press and release the LEARN button one time on the garage door opener. The LEARN LED will light.
  3. Enter the 4-digit PIN from step 2, then press and release the ENTER button until the garage door opener lights flash or two clicks are heard.
  4. Test by entering the programmed PIN and then pressing the ENTER button. The garage door opener will activate.

For a visual guide to programming, please refer to the full user manual diagram:

Full user manual page with detailed programming instructions and warnings

Image: Full user manual page detailing programming steps and warnings.

4. Operating Instructions

4.1. Basic Operation

The garage door opener activates when you enter your personal identification number (PIN) and press the ENTER button. The keypad will blink for 15 seconds, during which the ENTER button can be used to stop, start, or reverse the door. If an incorrect PIN is entered, simply enter the correct PIN and press ENTER; only the last four digits entered before ENTER will be transmitted.

4.2. One Button Close Feature

This feature allows you to close your garage door by pressing only the ENTER button (instead of your 4-digit PIN). This feature is for closing only and is not available on openers manufactured before 2006 or with an external receiver.

To Deactivate: Press and hold the '1' and '9' buttons for 10 seconds. The keypad will blink four times.

To Activate: Press and hold the '1' and '9' buttons for 10 seconds. The keypad will blink twice.

4.3. Programming a Temporary PIN

This feature is not available on openers with a green LEARN button or an external receiver. A temporary 4-digit PIN can be set for visitors, limited by hours or door openings. It cannot be the same as any existing PIN.

  1. Enter any programmed PIN, then press and hold the '*' button until the garage door opener light blinks three times.
  2. Enter the temporary 4-digit PIN of your choice, then press the ENTER button. The light blinks four times.
  3. Enter the temporary PIN limit of use:
Number of Hours PIN Will WorkNumber of Openings PIN Will Work
Press the number of hours (up to 255), then press the '#' button. The opener light blinks once.Press the number of openings (up to 255), then press the '#' button. The opener light blinks once.
  1. Test by entering the temporary PIN and pressing ENTER. The opener will activate (this uses one opening).

To clear a temporary PIN, repeat steps 1-4 and set the number of hours or openings to '0' at step 3.

4.4. Changing an Existing PIN

  1. Enter the programmed PIN you want to change.
  2. Press and hold the '#' button until the garage door opener light blinks twice.
  3. Enter the new 4-digit PIN of your choice and press the ENTER button. The opener light will blink once.
  4. Test by entering the new PIN and pressing the ENTER button. The garage door opener will activate.

Note: You cannot change an existing PIN for an opener with a green LEARN button or an external receiver. You must repeat the 'Program the Initial PIN' steps to change the PIN.

5. Maintenance

5.1. Battery Replacement

WARNING:

  • Never allow small children near batteries.
  • If a battery is swallowed, immediately notify a doctor.

Replace the 9V battery when the keypad becomes dim or does not light after a button is pressed. Slide the cover up, remove the battery cover, replace the battery, and dispose of the old battery properly.

5.2. Cleaning

Wipe the keypad with a soft, damp cloth. Do not use abrasive cleaners or solvents.

6. Troubleshooting

6.1. Keypad Not Responding or Dim

  • Check the battery. Replace the 9V battery if it is low or dead.
  • Ensure the battery is inserted with correct polarity.

6.2. Keypad Does Not Activate Opener

  • Verify that the keypad is within range of the garage door opener.
  • Recheck the programming steps for your specific garage door opener type (LEARN button color).
  • Ensure the garage door opener is receiving power.

6.3. Erasing All Remote Control and Keyless Entry Programming

This procedure will erase ALL remote controls and keyless entries from your opener.

  1. Press and hold the LEARN button on the garage door opener until the LEARN LED turns off (approximately 6 seconds).
  2. Test all remote controls and keyless entries to ensure they no longer activate the opener.
  3. Follow programming steps to reprogram each remote control and keyless entry you wish to use.

7. Specifications

  • Model Number: 878Max
  • Compatibility: LiftMaster garage door openers manufactured from January 1, 1993, with 315 MHz or 390 MHz frequencies and a LEARN button.
  • Encoding Method: Rolling code
  • Power: 9V battery
  • Dimensions: Approximately 16 cm (6.3 inches) height x 6 cm (2.36 inches) width
  • Features: Weatherproof flip-up protective cover, pure wireless keypad.
Dimensions of the 878Max Wireless Keypad

Image: Dimensions of the 878Max Wireless Keypad: 16cm/6.3inch height, 6cm/2.36inch width.

8. User Tips

  • Verify Compatibility: Before purchasing or attempting to program, always confirm your garage door opener's model and LEARN button color to ensure compatibility.
  • Clear Line of Sight: Ensure there are no major obstructions between the keypad and the garage door opener for optimal signal transmission.
  • Regular Battery Checks: Periodically check the keypad's responsiveness. If it seems sluggish or the lights are dim, it's a good indication to replace the battery.
  • Keep Clean: Wipe the keypad surface regularly to prevent dirt and grime buildup from affecting button presses.

9. Warranty and Support

9.1. One Year Limited Warranty

The Chamberlain Group, Inc. warrants to the first consumer purchaser of this product that it is free from defects in materials and/or workmanship for a period of 1 year from the date of purchase.

9.2. Support

For additional information and support, please visit: support.chamberlaingroup.com.

A PDF version of the user manual is also available for download from the seller's product page.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.