1. Introduction
Thank you for choosing the FADINI JUBI SMALL 433 Rolling Code Remote Control. This device is designed for reliable and secure operation of various automated systems, including garage doors, gates, alarms, and roller shutters. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your remote control.
Figure 1: Front view of the FADINI JUBI remote control, highlighting features like Security 2.0, Remote Dominance, ability to control one garage door, and lightweight design.
Video 1: Product overview showing the FADINI JUBI SMALL 433 remote control, its packaging, and a brief overview of its features.
2. Safety Information
- Keep the remote control out of reach of children to prevent accidental operation or ingestion of small parts.
- Do not expose the remote control to water, excessive humidity, or extreme temperatures.
- Avoid dropping the remote control or subjecting it to strong impacts.
- Dispose of used batteries according to local regulations.
3. Setup
3.1. Unboxing
Your package should contain the FADINI JUBI SMALL 433 remote control and a small instruction leaflet.
3.2. Battery Installation/Check
The remote control comes with a pre-installed 12V battery. If you need to check or replace the battery:
- Locate the small screw on the back of the transmitter.
- Carefully remove this screw.
- Gently separate the two halves of the casing to access the internal components and the battery.
- The remote uses a 12V battery. Ensure it is correctly seated with the positive (+) and negative (-) terminals aligned as indicated.
- Reassemble the casing and secure it with the screw.
Figure 2: A hand holding the FADINI JUBI remote control in front of an automated gate, emphasizing its self-learning capability and simple, five-second programming.
3.3. Programming (Pairing)
This remote control features a self-learning function, making programming straightforward. The exact programming procedure may vary depending on your existing FADINI receiver unit or original remote control. Generally, programming involves one of the following methods:
- Programming from the Receiver Unit: Locate the programming button on your FADINI gate or garage door opener receiver. Press this button, then press a button on your new remote control within a few seconds. Refer to your FADINI receiver's manual for specific instructions.
- Cloning from an Existing Remote: If your system supports cloning, you may be able to program the new remote by holding it near an existing, working remote and pressing specific button combinations on both. Consult your original remote's or receiver's manual for cloning procedures.
Important: For detailed programming instructions, always refer to the user manual of your FADINI gate/garage door opener system.
4. Operating the Remote Control
Once programmed, operating your FADINI JUBI SMALL 433 remote control is simple:
- Press the desired button on the remote control to activate or deactivate your automated system (e.g., open/close gate, turn on/off alarm).
- Ensure you are within the operational range of your receiver unit for reliable performance.
Figure 3: Visual examples of the FADINI JUBI remote control's scope of application, such as garage doors, alarms, automatic doors, and roller shutters.
5. Maintenance
5.1. Battery Replacement
When the remote control's range decreases or it stops responding, the battery may need replacement. Follow the steps outlined in Section 3.2 to open the transmitter and replace the 12V battery. Ensure the new battery is inserted with correct polarity.
5.2. Cleaning
Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents, as they may damage the casing or internal components.
5.3. Storage
Store the remote control in a dry place, away from direct sunlight and extreme temperatures, when not in use for extended periods.
6. Troubleshooting
- Remote not working:
- Check the battery. Replace if necessary (refer to Section 5.1).
- Ensure the remote is correctly programmed to your receiver (refer to Section 3.3).
- Verify that your receiver unit is powered on and functioning correctly.
- Limited operational range:
- Replace the battery.
- Check for any obstructions between the remote and the receiver.
- Ensure there is no radio interference in the area.
If problems persist, consult the manual for your FADINI gate/garage door opener system or contact a qualified technician.
7. Specifications
| Feature | Specification |
|---|---|
| Model | JUBI SMALL 433 |
| Frequency | 433.92 MHz |
| Encoding Method | Rolling Code |
| Battery Type | 12V |
| Dimensions (L x W x T) | 78mm x 40mm x 14mm (3.07in x 1.57in x 0.55in) |
| Compatibility | FADINI JUBI 433-2, JUBI 433-4, JUBI 433-2TR (JUBI SMALL) |
| Origin | Made in Italy |
Figure 4: Dimensions of the FADINI JUBI remote control: 78mm (3.07 inches) in length, 40mm (1.57 inches) in width, and 14mm (0.55 inches) in thickness.
8. User Tips
- Many users find this remote control very easy to program. Follow the instructions in your main gate/garage opener manual carefully for quick setup.
- Ensure your FADINI receiver unit is compatible with the JUBI SMALL 433 model for seamless integration.
- If you are replacing an old remote, verify that the new remote is identical in specifications (especially frequency and encoding method) to ensure proper functionality.
9. Warranty and Support
For warranty information and technical support, please refer to the documentation provided with your purchase or contact your retailer. Keep your proof of purchase for any warranty claims.