LiftMaster 893Max

Contents

893Max Wireless Remote Control User Manual

For Garage Door Openers and Gate Transmitters

1. Introduction

The 893Max Wireless Remote Control is a versatile device designed to operate various garage door openers and gate transmitters. It serves as a replacement remote for LiftMaster 80 Series, 970 Series, and 370 Series remote controls. This remote is compatible with 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993, and other products featuring a 'Learn' button.

The 893Max offers enhanced security with Security 2.0 technology, providing reliable remote dominance and the ability to control one garage door or gate. Its lightweight design makes it convenient for everyday use.

893Max Remote Control with Features
Figure 1: 893Max Remote Control highlighting Security 2.0, Remote Dominance, Single Garage Door Control, and Lightweight design.
893Max Remote Control Applications
Figure 2: The 893Max remote can be used for Garage Doors, Main Gates, Fences, Railings, and Sliding Doors.

Watch a brief overview of the 893Max remote control:

Video 1: Product showcase of the 893Max Wireless Remote Control.

2. Safety Information

WARNING: To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:

  • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls.
  • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
  • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross the path of a moving gate or door.

WARNING: Battery Safety

  • NEVER allow small children near batteries. If a battery is swallowed, immediately notify a doctor.
  • To reduce the risk of fire, explosion, or chemical burn: Replace ONLY with 3V CR2032 or 3V CR2016 coin cell batteries.
  • DO NOT recharge, disassemble, heat above 212°F (100°C), or incinerate.

3. Setup and Programming

Before programming, ensure your garage door opener has a working light bulb, as it often serves as a programming indicator. Locate the 'Learn' button on your garage door opener; its color (Yellow, Purple, Red/Orange, Green) indicates the opener type.

Detailed Remote Control Programming Steps
Figure 3: Detailed programming instructions for 893Max, 890Max, and 895Max remotes.

Programming the Remote Control (Method 1)

  1. Prepare: Locate the 'Learn' button on your garage door opener (it may be Green/Red/Orange, Purple, or Yellow). Also, locate the 'Program' button on your remote control.
  2. Enter Programming Mode: Press and hold the 'Program' button on the remote control until the LED on the front of the remote control turns on.
  3. Select Opener Type: Press and release the remote control button you wish to use a number of times that corresponds with your garage door opener type:
# of PressesGarage Door Opener Type
1Security+ 2.0™ (Yellow Learn Button)
2315 MHz Security+ (Purple Learn Button)
3390 MHz Security+ (Red/Orange Learn Button)
4390 MHz Billion Code (Green Learn Button)
  1. Exit Programming Mode: To exit programming mode, press any remote control button except the button that was just programmed.
  2. Activate Learn Mode on Opener: Press and release the 'Learn' button on the garage door opener. The 'Learn' LED will light for 30 seconds.
  3. Sync Remote with Opener: Within 30 seconds, press the remote control button programmed in step 3 until the garage door opener lights flash or two clicks are heard.
  4. Test: Press the programmed button on the remote control. The garage door opener should activate.
  5. Install Visor Clip: Install the visor clip (not applicable for Model 890MAX).

Programming Instruction (Method 2)

Simplified Remote Control Programming Steps
Figure 4: Simplified 4-step programming instruction.
  1. Step 1: Confirm Color of Learn Button and Frequency. Check what color the learn button is and its corresponding frequency on your garage door opener.
Color ButtonFrequency (MHz)Pressed Times
Yellow310, 3901
Purple3152
Orange3903
Red3903
Green3904
  1. Step 2: Programming Initiation. Hold down the hidden button on the remote until the LED lights, then release it.
  2. Step 3: Choose Code Type. Press and release the remote control button (one of the 3 buttons) you wish to use, according to the color of your learn button (refer to the table above). Then, press and release any other button 1 time to confirm.
  3. Step 4: Programming the Remote Control. Press and immediately release the learn button on your garage door opener. Then, the learn LED will glow steadily for 30 seconds, indicating the garage door opener is in a learning state. Release the button when the garage door opener lights blink or two clicks are heard. The programming is complete.

4. Operating Instructions

To operate your garage door or gate:

  1. Press and hold the desired button on the remote control down until the door or gate starts to move.
  2. The remote control typically operates from up to 3 car lengths away, though this can vary based on installation and environmental conditions.
  3. Additional buttons on the remote control can be programmed to operate up to 3 different devices, such as additional garage door openers, light controls, gate operators, or access control systems.
How to Use the Remote Control
Figure 5: Diagram showing how to use the remote control for a garage door and for multiple devices.

5. Maintenance (Battery Replacement)

The LED(s) on your remote control will stop flashing when the battery is low and needs to be replaced.

Battery Replacement Procedure:

  1. Open the Case:
    • For 893Max: Pry open the case first in the middle, then at each side (2 and 3) using the visor clip or a small flat tool.
    • For 890Max: Pry open the case with a screwdriver blade.
    • For 895Max: Remove the two screws and then open the case.
  2. Replace Battery: Carefully remove the old battery. Insert the new battery with the positive side (+) facing up.
  3. Battery Type: Replace the battery ONLY with a 3V CR2032 or 3V CR2016 coin cell battery (depending on your specific model).
  4. Close Case: Securely close the remote control case.
  5. Disposal: Dispose of old batteries properly according to local regulations.

6. Troubleshooting

If your remote control is not functioning as expected, consider the following:

  • Remote Not Responding: Check if the LED on the remote flashes when a button is pressed. If not, the battery may be low and needs replacement.
  • Garage Door/Gate Not Responding: Ensure the remote is properly programmed to your opener. Refer to the
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.