1. Introduction
This manual provides instructions for the installation, maintenance, and troubleshooting of the Eye Trailer Cap designed for the rear bumper towing hook of the Mazda 3 Axela Sedan, model years 2013 to 2019. This product is an aftermarket replacement part intended for vehicle component substitution.
Important Note: This product is intended for vehicle replacement use only.
2. Safety Information and Precautions
- Compatibility Check: Always verify your vehicle's model, year, configuration, and appearance before purchase. Failure to confirm compatibility is the buyer's responsibility.
- Professional Installation: No installation or remote support is provided with this product.
- Color Matching: Original paint may fade due to UV and environmental exposure. Minor color differences are normal. Purchase carefully if a strict color match is required.
- Unpainted Parts: If you receive unpainted parts, they are supplied in primer or raw condition. Primer color may vary, and minor scratches may exist. Painting is required before installation.
- Dimensional Tolerance: Reasonable dimensional tolerance applies, and minor fitment variation is normal.
- Local Regulations: Some exterior parts may be subject to local road regulations. The buyer must verify compliance, as the seller is not responsible for penalties.
3. Package Contents
Your package should contain one (1) Eye Trailer Cap for the Mazda 3 Axela Sedan rear bumper towing hook.
Available colors may include: Silver, Red, White, Blue, Black, No paint (Yellow), Glazed brown (Purple), and Gray.
4. Setup and Installation
- Verify Fitment: Before painting or permanent installation, a test fitting must be completed. Do not modify the structure of the cap or your vehicle. Issues caused by failure to test fit are the buyer's responsibility.
- Locate Tow Hook Cover: Identify the tow hook cover location on your vehicle's rear bumper. It is typically a small, circular or square panel.
- Install the Cap: Carefully align the new Eye Trailer Cap with the opening and press firmly until it clicks into place. Ensure all clips are securely fastened.
Note: Vehicle aging, such as clip fatigue or deformation, may affect installation. Such conditions are not considered product defects.
5. Operating Instructions
This product is a static cover for the towing hook. No operational steps are required after proper installation. It serves to protect the towing hook opening and maintain the aesthetic appearance of your vehicle's bumper.
6. Maintenance
- Cleaning: Clean the Eye Trailer Cap regularly with mild automotive soap and water to remove dirt and grime. Avoid abrasive cleaners that could damage the finish.
- UV Protection: To minimize paint fading due to UV exposure, consider applying a UV protectant wax or sealant suitable for automotive paint.
- Inspection: Periodically check the cap for secure fitment and any signs of damage or wear.
7. Troubleshooting
- Cap Does Not Fit:
- Re-verify your vehicle's model, year, and configuration against the product's compatibility.
- Ensure the cap is correctly oriented before attempting to install.
- Check for any obstructions or damage to the bumper opening or the cap's clips. Vehicle aging or fatigued clips might affect fitment.
- Do not force the cap into place or modify its structure.
- Color Mismatch: Minor color differences are normal due to factors like original paint fading from UV exposure. If a strict color match is critical, this product might not meet expectations as per the product's general notice.
- Damaged Upon Arrival: Inspect the packaging and product immediately upon delivery. Report any visible damage with photos to the seller promptly. Claims after acceptance may not be recognized.
8. Specifications
| Feature | Detail |
|---|---|
| Product Name | Eye Trailer Cap |
| Compatibility | Mazda 3 Axela Sedan (2013, 2014, 2015, 2016, 2017, 2018, 2019) |
| Placement | Rear Bumper Towing Hook Cover |
| Material | (Not specified, assumed plastic based on typical car parts) |
| Dimensions (Approx.) | Length: 15 cm, Width: 15 cm, Height: 15 cm (Package dimensions, actual product slightly smaller) |
| Weight (Approx.) | 0.035 kg (Package weight) |
| Colors Available | Silver, Red, White, Blue, Black, No paint (Yellow), Glazed brown (Purple), Gray |
| High-concerned chemical | None |
| Origin | Mainland China |
9. User Tips
- Color Match Expectation: While many users find the color match to be "almost exact" (as per a Mazda 3 2014 owner), be aware that minor variations can occur due to vehicle paint aging and manufacturing tolerances.
- Pre-Installation Check: Always perform a dry fit before any permanent steps or painting to ensure proper alignment and fit.
- Documentation: For additional guidance, you may refer to the Automotive Exterior & Interior Replacement Parts Manual (PDF) available at this link.
10. Warranty and Support
Warranty: This product comes with a 30-day limited warranty covering manufacturing defects only. This warranty explicitly excludes damage caused by improper installation, color variation (as noted in safety information), and modified products.
Reporting Issues: In case of any issues, inspect the product and packaging upon delivery and report visible damage immediately with photographic evidence. Claims made after acceptance may not be recognized.
Labor Costs: The seller is not responsible for labor costs incurred during installation or for vehicle downtime. Liability is limited to the purchase price of the product.
Further Information: For more detailed information, please refer to the Automotive Exterior & Interior Replacement Parts Manual (PDF) provided by the seller: https://manuals.plus/m/2c99840897f3d9008e253a4f5b2a6e4c391a15644c95bf124f3043dcf283b005