1. Introduction
Thank you for choosing the UGREEN 10-in-1 USB-C Docking Station. This device is designed to expand the connectivity of your USB-C enabled laptop, tablet, or game console, providing a comprehensive solution for data transfer, video output, network access, power delivery, and storage expansion. Please read this manual carefully to ensure proper use and optimal performance.
Key Features:
- 10-in-1 Connectivity: Includes HDMI, USB-A, USB-C, Gigabit Ethernet, SD/TF card reader, and an M.2 NVMe SSD slot.
- High-Speed Data Transfer: USB 3.2 Gen2 ports support up to 10Gbps.
- 4K Ultra HD Display: HDMI 2.0 output delivers 4K@60Hz video.
- Power Delivery: Supports up to 100W power input for charging your host device (85W max output).
- M.2 NVMe SSD Slot: Expand storage with NVMe PCIe M-Key and B+M Key SSDs (2230, 2242, 2260, 2280).
- Gigabit Ethernet: Stable and fast wired network connection (1000/100/10Mbps).
- SD/TF Card Reader: Supports simultaneous read/write at up to 170MB/s.
- Enhanced Safety: Built-in protections against short circuit, overheating, over voltage, and over current.
2. Package Contents
- UGREEN 10-in-1 USB-C Docking Station x1
- User Manual x1
- USB-C to USB-C Cable (1m) x1

Image: Retail packaging of the UGREEN 10-in-1 USB-C Docking Station.
3. Setup Instructions
3.1 Before Use: Important Notes
- Ensure your host device's USB-C port supports video output (DisplayPort Alternate Mode), data transfer, and power delivery. Not all USB-C ports are fully functional.
- For stable operation, especially when using high-power devices or charging your laptop, connect a power adapter (not included) to the PD port of the docking station.
- The M.2 SSD slot supports NVMe PCIe M-Key and B+M Key SSDs (sizes 2230, 2242, 2260, 2280). SATA-based M.2 SSDs are NOT supported.
- The USB-C data port (10Gbps) does NOT support video output or power delivery.
- The SD/TF card slots can be used simultaneously.
- For 4K@60Hz video output, ensure your host device and monitor support DisplayPort 1.4. If your device supports DisplayPort 1.2, the output will be 4K@30Hz.
3.2 M.2 NVMe SSD Installation
- Disconnect: Ensure the docking station is disconnected from all connected devices and power sources.
- Position: Place the docking station on its side with the removable cover panel facing upwards.
- Remove Panel: Loosen the two screws on the bottom panel and carefully remove it.
- Loosen SSD Screw: Locate and loosen the M.2 SSD fixing screw inside the slot.
- Insert SSD: Gently insert your M.2 NVMe SSD (M-Key or B+M Key) into the slot at an angle.
- Secure SSD: Press down the SSD and secure it with the fixing screw.
- Reattach Panel: Place the bottom panel back onto the docking station and tighten the two screws.
- Connect: Connect the docking station to your laptop. A new drive letter for the SSD should appear upon successful installation.

Image: Step-by-step visual guide for installing an M.2 NVMe SSD into the docking station.
3.3 Connecting to Your Host Device
- Connect one end of the provided USB-C to USB-C cable to the 'Host' port on the docking station.
- Connect the other end of the USB-C cable to the USB-C port on your laptop, tablet, or compatible game console.
- (Optional) Connect a USB-C power adapter (up to 100W) to the 'PD 100W' port on the docking station to power the hub and charge your host device.
- Connect your peripherals (monitor, mouse, keyboard, Ethernet cable, SD/TF cards, USB drives) to the corresponding ports on the docking station.

Image: Diagram illustrating the various ports and their functions on the UGREEN 10-in-1 Docking Station.
4. Operating Instructions
4.1 Port Functions
- HDMI 2.0 (4K@60Hz): Connect an HDMI cable from this port to your external monitor or TV for video and audio output. Supports resolutions up to 3840x2160 at 60Hz.
- USB-C Upstream Port (Host): Connects to your laptop/device.
- USB-C PD Input (100W Max): Connect a USB-C power adapter here to power the docking station and charge your host device.
- USB-A 10Gbps Data Port: For connecting USB-A devices requiring high-speed data transfer.
- USB-C 10Gbps Data Port: For connecting USB-C devices requiring high-speed data transfer (data only, no video/charging).
- 2x USB-A 5Gbps Data Ports: For connecting standard USB-A peripherals like mice, keyboards, or USB drives.
- Gigabit Ethernet (RJ45): Connect an Ethernet cable for a stable wired network connection (1000/100/10Mbps).
- SD & TF 3.0 Card Reader: Insert SD and microSD (TF) cards for data transfer. Both slots can be used simultaneously.
- M.2 NVMe SSD Enclosure (10Gbps): Provides expanded storage as detailed in the setup section.
- Power Button: To power on/off the docking station.
4.2 Power Delivery
When a USB-C power adapter is connected to the PD port, the docking station will pass through power to charge your connected laptop or host device. The docking station itself requires some power to operate, so the maximum output for charging your laptop will be approximately 85W (from a 100W input).
4.3 SSD Usage
Once an M.2 NVMe SSD is installed and the docking station is connected to your host device, the SSD will appear as an external drive. You can use it for file storage, backups, or running applications directly from it. Ensure safe ejection of the drive before disconnecting the docking station to prevent data loss.
5. Maintenance
- Keep the docking station clean by wiping it with a soft, dry cloth.
- Avoid using harsh chemicals or abrasive cleaners.
- Ensure proper ventilation around the device to prevent overheating.
- Store the device in a cool, dry place when not in use.
- Avoid dropping or subjecting the device to strong impacts.
6. Troubleshooting
- No Display Output:
- Ensure your host device's USB-C port supports DisplayPort Alternate Mode.
- Check the HDMI cable connection between the docking station and your monitor.
- Try a different HDMI cable or monitor.
- Ensure your monitor is set to the correct input source.
- Verify that your host device's display settings are configured to extend or duplicate the display.
- No Power Delivery/Charging:
- Ensure your USB-C power adapter is connected to the PD port and is functional.
- Verify that your host device's USB-C port supports power delivery.
- Try a different USB-C power adapter and cable.
- SSD Not Detected:
- Ensure the SSD is correctly installed and secured as per the installation steps.
- Verify that your SSD is an NVMe PCIe M-Key or B+M Key, not a SATA M.2 SSD.
- Check Disk Management (Windows) or Disk Utility (macOS) to see if the drive is recognized but unformatted.
- Try restarting your computer.
- Network Connection Issues:
- Ensure the Ethernet cable is securely connected to both the docking station and your router/modem.
- Check your network settings on your host device.
- Try a different Ethernet cable.
- USB Devices Not Working:
- Ensure the docking station is adequately powered, especially when connecting multiple power-hungry USB devices.
- Try connecting the USB device directly to your host device to confirm it's functional.
- Reconnect the docking station to your host device.
- Device Shuts Down (Windows Specific):
- Some users have reported issues with the device shutting down after a short period on Windows. This could indicate a defective unit or specific driver/compatibility issues. Ensure your Windows system is up to date. If problems persist, contact UGREEN support.
7. Specifications
| Feature | Specification |
|---|---|
| Brand | UGREEN |
| Product Name | 10-in-1 USB-C Docking Station |
| Model | CM923 - 55735 |
| HDMI Port | 4K@60Hz Max (HDMI 2.0) |
| PD Port | PD 100W (PD3.0 Input, 85W Max Output) |
| USB-C 3.2 Gen 2 (Data) | 1x 10Gbps (Backward Compatible with USB 3.0/2.0/1.1) |
| USB-A 3.2 Gen 2 (Data) | 1x 10Gbps (Backward Compatible with USB 3.0/2.0/1.1) |
| USB-A 3.0 Gen 2 (Data) | 2x 5Gbps (Backward Compatible with USB 2.0/1.1) |
| TF/SD 3.0 Card Reader | 170MB/s (Simultaneous Read/Write) |
| RJ45 Port | 1000/100/10Mbps Gigabit Ethernet |
| M.2 Slot | 1x 10Gbps (NVMe PCIe M-Key/B+M Key SSDs) |
| Cable Length | 1m |
| Dimensions | 149.5mm x 95.9mm x 60mm |
| Compatible Systems | Windows, macOS, Linux, Chrome OS, iOS, iPad OS, Android |
| Certifications | CE, FCC |

Image: Detailed product specifications for the UGREEN 10-in-1 USB-C Docking Station.
8. User Tips
- Mac Compatibility: Users have reported excellent performance and seamless integration with macOS devices.
- Windows Troubleshooting: If experiencing issues on Windows, such as the device shutting down after a short period, ensure your system drivers are up to date. If the problem persists, it might indicate a specific compatibility issue or a defective unit; consider contacting UGREEN support.
- Power for Stability: Always connect an external power adapter to the PD port when using multiple peripherals or charging your laptop to ensure stable operation.
9. Safety Information
- Avoid dropping, disassembling, or attempting to repair this product yourself.
- Do not expose this product to water, moisture, or extreme temperatures.
- Keep out of reach of children.
- For optimal performance and safety, use the provided USB-C cable.
- The device incorporates multiple safety features including short circuit, overheating, over voltage, and over current protection.

Image: Icons representing short circuit, overheating, over voltage, and over current protection.
10. Warranty and Support
UGREEN products come with a limited warranty. For detailed warranty information, product support, or technical assistance, please visit the official UGREEN website or contact their customer service directly. Please have your product model number (CM923-55735) and purchase information ready when contacting support.