TOP-MAX LED Side Marker Light Indicator Rubber Lamps

Contents

LED Side Marker Light Instruction Manual

Model: LED Side Marker Light Indicator Rubber Lamps

1. Product Information

Thank you for choosing the TOP-MAX LED Side Marker Lights. These durable and versatile lights are designed to enhance visibility and safety for a wide range of vehicles.

LED Side Marker Lights on a truck

Image showing the LED side marker lights installed on a truck, demonstrating their illumination and visibility.

Front view of red and white LED side marker lights

Front view of the red and white LED side marker lights, showcasing their distinct colors and LED arrangement.

Package Contents:

  • 2 x LED Side Marker Lights

2. Safety & Warnings

▲ Warning:

Before installing or replacing the side lights, the vehicle's power switch must be turned off, the engine must be turned off, and if necessary, the negative terminal of the battery must be disconnected to prevent circuit short circuits and leakage, and to avoid electric shock or damage to the vehicle's electrical system.

Always ensure proper insulation of all wiring connections to prevent electrical hazards.

CE Mark

The product complies with CE standards. For detailed compliance information, please refer to the User Manual (PDF).

3. Setup & Installation

3.1 Pre-Installation Test

  • Before permanent installation, connect the wiring harness to the vehicle's electrical system.
  • Test all intended functions (e.g., daytime running, turn signal, reverse) to ensure the lights are functioning properly.

3.2 Mounting

  • Clean the desired installation surface thoroughly to ensure proper adhesion.
  • Determine the precise mounting position (e.g., top of the wheel arch, fender). Mark this position with a marker pen.
  • Carefully heat the backing adhesive on the light unit (a heat gun or hairdryer can be used on a low setting) to improve its stickiness.
  • Firmly press the light into the marked position, ensuring good contact with the surface.

3.3 Wiring Harness Routing

  • Route the wiring harness along existing gaps in the vehicle body (e.g., inner side of wheel arches, side skirts, door rubber strips).
  • Secure the wiring harness using zip ties to prevent it from dangling or interfering with moving parts.
  • If routing through a body sheet metal hole, install a rubber sleeve (grommet) to protect the wire insulation from abrasion.
Side profile of red LED side marker light

Side profile of the red LED side marker light, showing its elbow rubber base.

Side profile of white LED side marker light

Side profile of the white LED side marker light, showing its elbow rubber base.

4. Wiring Instructions

4.1 Power Supply Connection

  • Connect the red wire to the ACC (Accessory) power supply (e.g., a fuse in the fuse box that is active when the ignition is on, or the cigarette lighter fuse).
  • Connect the black wire to a reliable ground point on the vehicle's chassis or body metal.

4.2 Turn Signal Connection

  • The yellow wire (or other designated signal wire) must be connected in parallel to the vehicle's existing left/right turn signal wire.
  • Use a non-breaking clip for this connection.
  • A 1-3A fuse must be connected in series in the middle of this connection for protection.

4.3 Reverse Signal Connection

  • The white line is connected in parallel to the vehicle's reverse light signal line.
  • A fuse is also connected in series for this connection.

4.4 Insulation and Fixing

  • All wiring points must be wrapped with heat shrink tubing or velvet tape to ensure proper insulation and protection from moisture and abrasion.
  • Secure the newly installed wiring harness to the original vehicle wiring harness using zip ties to prevent loosening due to vibrations.

5. Operating Instructions

Once properly installed and wired, the LED side marker lights will operate in conjunction with your vehicle's electrical system. They will illuminate as side markers, flash as turn signals, or activate as reverse lights, depending on how they are connected to the corresponding vehicle circuits.

5.1 Post-Installation Testing

  • After completing the installation, retest all functions (daytime running, steering, reverse, etc.) to ensure they are working correctly.
  • Visually inspect all connections for any signs of electrical leakage or loose wiring.

6. Maintenance

  • Regularly clean the surface of the lights with a soft cloth and mild soap to remove dirt and debris, ensuring maximum light output.
  • Periodically check all wiring connections for corrosion or looseness. Re-secure or re-insulate as necessary.
  • Inspect the rubber base for any signs of cracking or deterioration, which could compromise the light's waterproof seal.

7. Troubleshooting

  • Lights not illuminating: Check the power supply connection (red wire) and ensure it has power. Verify the ground connection (black wire) is secure. Check the inline fuses for the turn signal and reverse light connections.
  • Lights flickering or dim: Inspect all wiring for loose connections or corrosion. Ensure the voltage supply is stable (12V or 24V as appropriate for your vehicle).
  • Water inside the light: Although waterproof, extreme conditions or improper installation can lead to moisture ingress. Check the integrity of the rubber base and the seal around the light.

8. Specifications

Dimensional diagram of the side marker light

Dimensional diagram of the side marker light, illustrating key measurements for installation.

Detailed dimensional diagram of the side marker light

Detailed dimensional diagram of the side marker light, including mounting hole spacing.

FeatureDetail
Product NameCar Side Marker Light
Brand NameTOP-MAX
OriginMainland China
Item TypeFender Marker / Side Marker
Light Source6 LEDs per side
Voltage12V & 24V systems
MaterialRubber, Plastic
Base TypeHeavy-duty rubber base
FeaturesShockproof, Waterproof, Flexible
Package Weight0.385 kg
Package Dimensions (L x W x H)13cm x 13cm x 9cm

9. User Tips

  • For optimal adhesion, ensure the mounting surface is completely dry and free of grease or wax before applying the lights.
  • When heating the adhesive, do so gently and evenly to avoid damaging the light unit.
  • Consider using additional sealant around the edges of the light after installation for extra protection against water ingress, especially in harsh weather conditions.
  • Always double-check local regulations regarding vehicle lighting before installation to ensure compliance.

10. Warranty & Support

Warranty Information

  • All products come with a 12-month warranty from the date of purchase.
  • Enjoy 7 days to return the product if there are any quality problems.

Customer Service

Our customer service team is available 24/7. Your inquiries will be replied to within 6 hours.

For support, please contact us via email at tingting26181@outlook.com.

11. Manufacturer & EU Representative Information

Manufacturer

Guangzhou Kuxiong Shi Trading Co., Ltd
No. 503, Building 3, Courtyard 2, Zhongquantang Road, Industrial Avenue, Haizhu District, Guangzhou City

Phone: 86-18814180059
Email: tingting26181@outlook.com

EU Authorized Representative

Sea&Mew Consulting GmbH
Mittenhuber Straße 4, 92318 Neumarkt

Phone: +4915224685061
Email: Compliance.EU@outlook.com

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.