1. Safety Information
⚠ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
1.1. Important Safety Warnings
- Avoid Water: The electric bike is not waterproof. Electronics may be damaged by water, and water damage is not covered by warranty. Riding in wet conditions is also dangerous.
- Exposure: Avoid prolonged exposure to sun or rain. Do not store in places with high temperatures or corrosive gas.
- Abuse: Physical damage due to negligent care and extreme riding is not covered.
- Risk of Injury: Riding an electric bike carries a risk of severe injury or death from loss of control, collisions, and falls. Use caution and ride at your own risk.
- Modifications: Do not modify the product from the manufacturer's original design.
- Traffic Laws: Do not exceed the posted speed limit and obey all traffic laws.
- Charging Port: Avoid touching the charging port directly and do not let it contact metal objects.
- Moving Parts: Keep hands and all body parts away from moving parts while operating the electric bike.
- Pre-Ride Check: Before riding, ensure the electric bike is operating correctly, the braking system functions properly, and all safety labels are in place.
- Tires: Check that tires are in good condition, properly inflated, and have sufficient tread.
- Age Restriction: The electric bike should never be used by children under the age of 18. Parental permission is required for riders under 18.
- Insurance: Additional insurance may be required. Contact an insurance company for advice.
- Charging: Always charge the battery in temperatures between 50°F-77°F (10°C-25°C). Do not charge for more than 12 hours or leave unattended.
1.2. Safety Precautions for Riding
- Wear a Helmet: Always wear a helmet that complies with state laws.
- Visibility: Make yourself more visible by wearing bright reflective clothing.
- Road Laws: Always be aware of local road laws and follow them.
- Impairment: Do not ride under the influence of drugs or alcohol.
- Pedestrians: Always respect pedestrians.
- Wet Conditions: Do not ride under wet conditions as the bike may slide, causing injury. Wet conditions may also damage electronics and void the warranty.
- Battery Keys: Keep the two unique keys properly. If lost, you won't be able to turn on the bike or replace the battery.
- Pre-Ride Check: Ensure your electric bike has a full battery before riding.
- Braking: Practice braking and stopping gently without locking the wheel.
- Overload: Avoid carrying heavy loads, including other people.
- Tire Pressure: Ensure tires have enough pressure, generally 35PSI-65PSI (280KPA-450KPA).
- Obstacles: Be careful of obstacles and slippery roads. Do not ride on grass or cobblestones.
- Water Depth: Do not ride in water deeper than 30mm.
- Immersion: Do not immerse the scooter in water.
- Slopes: Do not climb slopes over 30°, and do not accelerate or decelerate sharply on slopes.
- Highway: Do not ride the scooter on highways.
- Distractions: Do not wear headphones or use cell phones while riding.
- Passengers: The scooter is for individual use and cannot be used by multiple persons.
2. Package Contents
Carefully check the package contents upon receipt. If anything is missing or damaged, please contact customer service at ebikesservice@outlook.com.
Unpack the bike by opening the box and removing the small box inside. With assistance, remove the bike from the box. Carefully remove all packaging materials. Recycle cardboard and foam where possible. Set out all contents from the small box.
Image: ZEFIORA V10 Electric Bicycle Model and various components included in the package.
2.1. Items Included:
- Electric Bike (x1)
- User Manual (x1)
- Seat (x1)
- Pedals (x2)
- Wrenches (x2)
- Allen Key Wrenches (x3)
- Kickstand (x1)
- Keys (x2)
- Front Wheel (x1)
- Charger (x1)
- Fender (x2)
- Mobile Phone Holder (x1)
- Car Lock (x1)
3. Setup (Assembly)
If you encounter difficulties during installation, please contact customer service for assistance and a video guide.
3.1. Front Fork Assembly
- Remove the front wheel and install it on the front fork.
- Install the front wheel anti-spin hook and nut, then tighten them.
Image: Detailed view of front fork assembly, showing the installation of the wheel, anti-spin hook, and nut.
3.2. Fender & Headlight Installation
- Take out the fender, remove the nut, washer, and bolt at the top of the front fork.
- Fix the headlight and fender to the fixed position on the front fork with screws.
- Use a cross screwdriver to loosen the screw at the rear mudguard clip position, then separate the clip by hand and hook it under the saddle tube clamp.
- Adjust to the proper position and tighten the screws with a cross screwdriver to secure the mudguard.
- Locate the headlight wiring harness and the main wiring harness (with arrow markings). Align and insert them securely.
- Secure the mounting brackets on both sides with screws.
3.3. Brake Tension Adjustment
Squeeze the brake caliper arms by hand to pull the cable tight. While squeezed, tighten the locknut firmly. For your safety, spin the wheel and test the brakes before riding.
Image: Diagram illustrating how to adjust brake tension by squeezing caliper arms and tightening the locknut.
3.4. Abnormal Brake Noise Adjustment
Abnormal noise is often caused by thicker brake pads. This is normal and will subside after a few days of wear. If noise persists:
- Prepare Tools: Locate the disc brake caliper (metal part holding the brake disc) and the two vertical screws (usually M6 Allen wrench).
- Loosen Screws: Slightly loosen these two screws (one to one and a half turns) to allow the caliper to move. Do not remove them completely.
- Alignment: Gently straighten the wheel to ensure it's centered. Adjust the brake caliper position to align the brake disc exactly in the center of the two brake pads, with even clearance. Rotate the wheel to check for friction noise.
- Tighten Screws: Alternately and gradually tighten the two loosened screws. Do not overtighten one screw at once.
3.5. Stem Assembly
- Loosen the screws to remove the front fork sleeve.
- Take out the stem and insert it into the front frame.
- Tighten the screws to fix the stem in place.
- Align the stem with the tire direction, then tighten the clamping screws below the stem.
3.6. Kickstand Installation
- Use a screwdriver to fix the screws on the kickstand.
- Secure the kickstand to the designated position on the bike.
- Fasten the screws on the right side.
- Fix the screws on the left side, ensuring they are locked to prevent falling off during riding.
3.7. Pedals Assembly
- Locate the right-side ('R') and left-side ('L') pedals.
- Thread the right pedal onto the right crank clockwise by hand, then tighten with an Allen wrench.
- Thread the left pedal onto the left crank counter-clockwise by hand, then tighten with an Allen wrench.
- Check chain alignment by rotating the right pedal backward. Ensure the chain runs smoothly through the drivetrain.
3.8. Seat Assembly
- Loosen the quick-release screws on the saddle clamp to install the seat post.
- Move the seat up and down by sliding the seat post in or out of the seat tube.
- Tighten the screws to fix the seat post in place.
- Align the stem with the tire direction, then tighten the clamping screws below the seat post.
Proper seat height is crucial for comfort and safety. Your hips should remain level, and legs almost fully extended with a slight bend at the knee when the pedal is at its lowest point.
3.9. Rear Rack Installation
- Locate the taillight, loosen its screws, and remove it.
- Unscrew all four screws on the back.
- Place the rear rack in position, align the holes, and tighten the screws on both sides.
3.10. Taillight and Rear Seat Bag Installation
- Locate the taillight wiring and secure it with cable ties.
- Place the rear seat bag as shown in the picture, then tighten the fixing screws above the rear fender.
4. Operating Instructions
4.1. Instrument Display and Settings
Image: ZEFIORA Electric Bike Instrument Display showing battery level, speed, gear, and various icons.
- Power On/Off: Press and hold the [Power button] for 2 seconds.
- Gear Shifting: Press the [+] button to increase gear, [-] button to decrease gear.
- ODO/TRIP Toggle: Briefly press the [Power button] to switch between ODO (total distance) and TRIP (single trip distance). Default is TRIP.
- Implementation Model: Press and hold the [-] button to enter, release to exit.
4.1.1. Setting Menu Operations
To access general settings, press and hold both the [+] and [-] buttons simultaneously.
- Switch Items: Briefly press the [Power button].
- Adjust Parameters: Press [+] or [-] buttons.
- Confirm: Press and hold the [Power button] to save.
- Return to Home: Press and hold the [-] button to exit without saving, or remain inactive for 60 seconds.
Available Settings:
- SET 1: Wheel Diameter: Adjustable range 16-29 inches. (Not adjustable by default)
- SET 2: Speed Limit: Adjustable range 1-99 km/h. Default 25 km/h. (Not adjustable by default)
- SET 3: Unit: Metric (KM/H) or Imperial (blank). Default KM/H.
- SET 4: Screen Brightness: Adjustable range 1-3 levels. Default Level 3.
- SET 5: Auto Sleep Time: Adjustable range 1-60 minutes. Default 10 minutes.
- SET 6: Single Trip Auto Reset: Set to "y" to clear trip mileage on startup, "n" to retain.
4.2. Battery Removal and Installation
Removal Procedure:
- Insert the key into the lock and turn it counterclockwise to the left. The battery will pop out.
- Prop up the battery with one hand and remove it with both hands.
Installation Procedure:
Ensure the battery is turned off. Slowly align and push the battery down into the frame mount receptacle. Do not force it. Ensure it is properly secured by pulling upwards with both hands.
Caution: Be careful not to drop or damage the battery. Avoid damaging exposed connector terminals and keep them clear of debris.
4.3. Charging Your E-Bike
Before using the electric bike, you must fully charge the battery.
- Ensure the battery is off by rotating the key to align with the off icon.
- Remove the rubber cover on the charging port (opposite side of the battery from the key switch).
- Plug the charger into the battery's charging port. Place the charger on a flat, secure surface.
- Plug the charger into a power outlet. Charging is indicated by a red LED light on the charger.
- Once fully charged, the light will turn green. Unplug the charger from the wall outlet first, then remove the output plug from the battery.
Attention: Make sure the charger light faces upwards. Full charge normally takes 3-7 hours. Charge in a clean, safe place and do not overcharge. Do not charge for more than 12 hours.
Image: Close-up of the ZEFIORA Electric Bike charging port.
4.4. Gear Operation
Multi-speed bicycles have internal or derailleur gear systems. Improper shifting can cause chain jamming or derailment, leading to loss of control or a crash. Always ensure the chain is fully engaged in the desired gear before pedaling hard.
Avoid shifting while standing up on the pedals or under load.
To shift properly, pedal with little pressure and move the shifter one gear at a time. For bikes with 3 front chain rings, avoid "Cross Chaining" (smallest cog in rear with inner/smallest chain ring in front, or largest cog in rear with outer/largest chain ring in front) to prevent premature wear.
5. Maintenance
Regular inspection and maintenance are crucial for optimal function and to reduce wear. Service intervals may vary based on usage conditions.
5.1. Daily Care and Cleaning
- Cleaning: Wipe stains off the bike body with a damp cloth. For stubborn stains, use toothpaste and a toothbrush.
- Avoid: Do not clean with alcohol, gasoline, kerosene, or corrosive chemicals. Do not wash with a high-pressure water spray.
- During Cleaning: Ensure the bike is off, charging cable unplugged, and rubber flap closed to prevent electric shock or other problems.
- Storage: Store indoors in a dry, cool place. Avoid prolonged outdoor exposure, excessive sunlight, overheating, or overcooling, which can shorten battery life.
5.2. Battery Maintenance
- Use original battery packs only.
- Do not touch contacts, dismantle, or puncture the casing. Keep contacts away from metal objects.
- Use the original power adapter.
- Dispose of used batteries according to local regulations.
- Fully charge the battery after every use to prolong its life span.
- If storing for more than two months, charge regularly (every other month) to maintain battery health.
- Store in a dry, low-humidity place between 5°C-20°C.
- Protect from extreme temperature fluctuations and direct sunlight.
5.3. Recommended Service Intervals
| Interval | Inspect | Service | Replace |
|---|---|---|---|
| Weekly (100-200 mi) |
|
|
Damaged components |
| Monthly (250-750 mi) |
|
|
Brake/shift cables, brake pads |
| Every 6 Months (750-1250 mi) |
|
|
Brake pads, tires, cables/housings |
6. Troubleshooting
If you experience any issues, refer to the table below. If the problem persists, contact customer service.
6.1. Fault Code Comparison Table (Instrument Display)
| No. | Data Status | Meaning | Instrument Display |
|---|---|---|---|
| 1 | 0x21 | Controller Fault | 21 |
| 2 | 0x22 | Throttle Fault | 22 |
| 3 | 0x23 | Motor Phase Loss | 23 |
| 4 | 0x24 | Hall Sensor Fault | 23 |
| 5 | 0x25 | Undervoltage Protection | 25 |
| 6 | 0x26 | Brake Lever Fault | 26 |
| 7 | 0x30 | Communication Fault | 30 |
6.2. Basic Troubleshooting Table
| Symptoms | Possible Causes | Most Common Solutions |
|---|---|---|
| Bike does not work |
|
|
| Irregular acceleration / Reduced top speed |
|
|
| Motor does not respond |
|
|
| Reduced range |
|
|
| Battery will not charge |
|
|
| Wheel or motor makes strange noises |
|
|
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | ZEFIORA |
| Model Number | V12 (also M10, Z10, S10 variants) |
| Certification | CE |
| Style | Standard Type |
| Max Speed | 30 - 50 KM/H (20MPH/H for 14" model) |
| Range per Power | 31 - 60 km |
| Wattage | > 500w (500W P≤740w for 14" model) |
| Power Supply | Lithium Battery |
| Voltage | 48V |
| Motor Type | Brushless Hub Motor |
| Frame Material | Aluminum alloy / High Carbon Steel |
| Folded | No |
| Product Dimensions (M10/M12) | 135*22*72 cm |
| Package Dimensions (M10/M12) | 168*23*98 / 168*25*104 cm |
| E-Bike Weight (M10/M12) | 50.7lb (23kg) / 55.1lb (25kg) |
| Battery Capacity | 48V 10Ah (also 15Ah, 17.5Ah, 20Ah variants) |
| Charger Output | 54.6V 2A |
| Charging Time | 3-6 Hours (or 5-7 Hours for 14" model) |
| Tire Pressure | 40-65 PSI |
| Bell/Horn | Electric Horn Installed |
| Anti-vibration mounting (14" model) | Four shock absorbers |
| Car light (14" model) | Front and rear lamps and brake taillight |
| Package weight (14" model) | 33KG |
| Tire Model (14" model) | 14 x 2.215IN A/V nozzle |
8. User Tips
- Key Management: Always keep your unique battery keys safe. Without them, you cannot turn on the bike or replace the battery. Consider getting spare keys if available.
- Energy Conservation: To maximize range, use assist mode, avoid sudden starts, frequent braking, riding against strong winds, and carrying heavy loads. Ensure tires are properly inflated.
- Optimal Riding: For the best endurance mileage, ride in low-speed mode and avoid frequent braking when safety allows. Prevent overloading the bike.
- Battery Charging Temperature: Always charge your battery within the recommended temperature range of 50°F-77°F (10°C-25°C).
- Regular Charging: Recharge the battery after each use to ensure it's ready for the next ride. Lithium batteries do not suffer from memory effect.
- Avoid Overcharging: Do not charge the battery for more than 12 hours at a time, and never leave it unattended while charging.
9. Warranty and Support
This product comes with a limited warranty. For any questions or support, please contact us.
Contact Email: ebikesservice@outlook.com
We aim to reply and resolve problems within 24 hours. When contacting support, please provide your order ID and detailed photos/videos of the issue.
9.1. Warranty Exclusions
The warranty does not cover:
- Consumables and gift items.
- Faults caused by operation not in accordance with the user manual.
- Normal wear and tear, accidents, abuse, neglect, improper assembly, or improper maintenance.
- Improper use of accessories.
- Parts subject to natural wear under normal use.
- Failure of correct change and maintenance or damage due to wear of consumables.
- Warranty card not matching the scooter model or changed scooter model.
- Damage caused by overloading, riding over obstacles (e.g., going down steps, falling), or extreme sports.
- Damage caused by force majeure (e.g., fire, earthquake, lightning strike, flood).
- Issues outside the warranty period.
- Damage caused by over-discharge or under-discharge of the battery.
- Damage caused by collision during use.
For a detailed user manual in PDF format, please refer to the official document: User Manual (PDF)
10. Product Video
Watch this video for a closer look at the ZEFIORA V12 Electric Bicycle Model, including battery features and accessories.
Video: Overview of the ZEFIORA V12 Electric Bicycle Model, showcasing its design, battery compartment, and included phone holder.