1. Introduction
The IKSLED Mini Copper Touch Sensor Switch provides versatile touch control for various applications, including LED lighting and water level detection. It features a compact design with a 10mm copper sensing sheet and supports dual-mode operation. This manual provides essential information for safe and effective use of the product.
2. Safety Information
WARNING: Please strictly follow these instructions and safety tips. Use the product with caution.
- Ensure all wiring is correct before applying power.
- Do not exceed the maximum load specifications for the working voltage.
- Avoid using induction switches with control motors, solenoid valves, solar lights, constant current lamps, and other incompatible equipment.
- Keep the switch fixed and stable during operation to prevent environmental interference.
3. Product Specifications
| Attribute | Value |
|---|---|
| Brand Name | IKSLED |
| Model Number | 10T Copper Switch |
| Switch Type | Touch On/Off Switch |
| Material | Copper |
| Rated Voltage | 3.7V to 24V DC |
| Max Current | Less than or equal to 2.5A |
| Power | Max. 60W |
| Copper size | 10mm |
| Sensing Material | Plastic/glass (up to 4mm thickness) |
| Application | LED light/water level detection/penetrate 4mm plastic/glass |
| Use | Mini touch sensing module water level monitor |
| Is Smart Device | No |
| Certification | RoHS, LVD, EMC, CE, CCC |
| EU LVD Voltage | Low voltage: Below 50Vac or 75Vdc |
| High-concerned chemical | None |
| Origin | Mainland China |
4. Setup
4.1. Components
The product package typically includes the Mini Copper Touch Sensor Switch with attached wires.
4.2. Wiring Diagram
Connect the wires according to the diagram below. Ensure correct polarity (Positive/Negative) for both input power and output to the connected device (e.g., LED light, motor, buzzer).
Input Voltage: The switch supports a working voltage range of 3.7V to 24V DC. Ensure your power adapter and connected device (e.g., LED light) operate within this range and match each other.
4.3. Installation Steps
The induction switch can penetrate plastic or glass up to approximately 4mm thick, allowing for hidden installations.
- Connect the LED light or other compatible device to the sensor switch according to the wiring diagram.
- Apply double-sided tape to the back of the copper sensing sheet.
- Tear off the protective film from the tape.
- Secure and fix the induction switch firmly in the desired location. Ensure it is stable and not moving.
- Finally, turn on the power supply for use.
5. Operating Instructions
The Mini Copper Touch Sensor Switch offers two main operational modes, typically referred to as Model A and Model B, depending on the specific version of your switch.
5.1. Model A Operation
- Touch to Turn ON, Release to Turn OFF: The device activates when the copper sheet is touched and deactivates when the touch is released.
5.2. Model B Operation
- Short Touch ON/OFF: A brief touch to the copper sheet will toggle the connected device (e.g., LED light) between ON and OFF states.
- Long Press to Adjust Brightness: When the device is ON, a sustained touch (long press) on the copper sheet will allow you to adjust the brightness level (dimming function).
5.3. Application Example: Water Level Monitoring
The sensor can be used for water level detection. When the water level drops below the sensor's position, the connected light will automatically turn off, indicating a low water level.
6. Troubleshooting
Problem: The LED light remains on or off, and the switch cannot be controlled.
This issue can arise from three common reasons:
- Mismatch of Working Voltage: The voltage of the power adapter does not match the voltage required by the LED light or the switch.
- Reversed Polarity: The input/output or positive/negative poles are connected in reverse.
- Incorrect Usage Steps/Unstable Installation: The induction switch was fixed after power was already on, or the switch is not fixed and moves during use, causing it to constantly detect environmental changes.
Resolution:
- Check Voltage Compatibility: First, confirm that your power adapter provides a constant DC voltage (3.7V, 5V, 12V, or 24V) and that your LED light is compatible with the same DC voltage.
- Verify Polarity: Check if the input/output and positive/negative poles are connected correctly. If they are reversed, disconnect power and reconnect them with the correct polarity.
- Ensure Proper Installation: Turn off the power supply. Securely fix the induction switch in its intended position. Once fixed, then turn on the power to use the device.
7. Warranty and Support
This product comes with a 1 Year Warranty from the date of purchase. For technical support or warranty claims, please refer to the seller's contact information.
A detailed user manual in PDF format is also available for download. You can access it here: User Manual (PDF).