1. Warning & Safety Information
- Do not use in humid environments.
- Avoid areas with strong electromagnetic interference.
- Disconnect power before installation.
- When inserting or removing hardware, take care not to damage motherboard pins.
- Prevent electrostatic discharge (ESD) damage during installation.
- Do not force insertion or removal of hardware components.
- Ensure adequate ventilation and heat dissipation.
2. Product Overview
The Jingsha B75 HM Motherboard is designed for Intel processors with an LGA 1155 socket, supporting 2nd and 3rd generation Core i3/i5/i7, Pentium, and Celeron CPUs, as well as Intel Xeon E3 V1/V2 processors. It features 4 DDR3 memory slots, an NVMe M.2 port, and an M.2 KeyA/E WIFI port for wireless connectivity.
Key Features:
- LGA 1155 CPU Socket
- 4 DDR3 Memory Slots (Dual Channel, up to 32GB)
- NVMe M.2 Port (PCIEx4 Gen2 speed)
- M.2 KeyA/E WIFI Port (supports WIFI+Bluetooth)
- USB 3.0 and SATA 3.0 Support
- Gigabit LAN (Realtek RTL8111F Chipset)
- 4-pin CPU_FAN Connector




3. Specifications
| Component | Specification |
|---|---|
| Brand Name | JINGSHA |
| Model | B75-HM |
| Form Factor | M-ATX, 223.5mm x 195mm |
| CPU Socket | LGA 1155 |
| Supported Processors | Intel Pentium / Celeron / Core i3 i5 i7 (2nd/3rd Gen), Intel Xeon E3 V1/V2 |
| Memory Sockets | 4 x DDR3 (1066/1333/1600MHz) |
| Max Memory Capacity | 32GB (Dual Channel Architecture, 1.5V non-ECC) |
| Graphic Card Slot | 1 x PCI-E 16X, 1 x PCI-E 1X |
| Storage Interface | 1 x SATA 3.0, 3 x SATA 2.0 |
| M.2 Slots | 1 x NVMe M.2 (PCIEx4 Gen2 speed), 1 x NGFF M.2 KeyA/E (for WIFI+Bluetooth) |
| USB Ports | 4 x USB 3.0, 6 x USB 2.0 |
| LAN | 1 x Realtek RTL8111F Gigabit Ethernet |
| Audio | Realtek Audio Codec ALC662, 5.1 Sound Channel |
| PSU Solution | ATX 4Pin + ATX 24Pin |
| Graphics | Integrated (requires CPU with integrated graphics support) |
| Accessories | 1 x I/O Shield, 1 x SATA cable |


4. Installation & Setup
Follow these steps to install your CPU and memory modules onto the motherboard.
CPU Installation:
- Press the wire buckle by hand and lift it up. Remember not to remove the black cover before installing the CPU.
- The motherboard base has 3 bayonets, and the CPU itself has three bayonets (red circles in the figure). Please align them one by one, and then put them all down.
- Lower the wire buckle that was lifted up, and the black cover on it will pop up automatically. Remember not to remove the black cover before installing the CPU.

Memory Module Installation:
- Open the retention clips on both ends of the DDR3 memory slots.
- Align the memory module with the slot, ensuring the notch on the module matches the key in the slot.
- Press down firmly on both ends of the memory module until the retention clips snap into place.
Power Connections:
Connect the 24-pin ATX power connector and the 4-pin ATX CPU power connector from your power supply to the corresponding ports on the motherboard. Ensure all connections are secure before powering on the computer.
Visual Installation Guide:
5. Operating Instructions
After successful installation of all components and power connections, you can power on your computer. The motherboard will initiate the boot sequence. Ensure your operating system is installed on a recognized storage device.
6. Maintenance
- Regularly clean dust from the motherboard and components using compressed air to ensure optimal cooling and prevent overheating.
- Ensure proper airflow within your PC case by managing cables and maintaining adequate space around components.
- Keep your BIOS/UEFI firmware updated to benefit from performance improvements, bug fixes, and compatibility enhancements.
7. Troubleshooting (FAQ)
- Q: System fails to power on.
- A: Verify that all power connections are secure, and that the CPU and memory are properly installed.
- Q: Experiencing Blue Screen of Death (BSOD).
- A: Update the motherboard BIOS or verify hardware compatibility with your installed components.
- Q: Hard drive not recognized.
- A: Confirm that the SATA cable is correctly connected to both the hard drive and the motherboard. Check BIOS settings to ensure the drive is detected.
- Q: CPU fan runs at 100% all the time.
- A: Check your BIOS settings for fan control options. Many motherboards allow you to set fan curves or profiles to adjust fan speed based on CPU temperature.
8. User Tips
- Power Supply: This motherboard requires a powerful power supply. Ensure your power supply is sufficient to support your entire system, with at least a 500W brand power supply recommended.
- CR2032 Battery: The CR2032 battery (CMOS battery) is typically removed before shipment due to shipping regulations. You will need to install a new CR2032 battery for the motherboard to retain BIOS settings and time.
- BIOS/Drivers: If you need BIOS files or drivers, contact customer service for assistance.

9. Warranty & Support
For any technical support, BIOS files, drivers, or warranty inquiries, please contact the seller or Jingsha customer service directly. Keep your purchase records for any warranty claims.