1. Introduction
This manual provides instructions for the installation, operation, and maintenance of the HORACO LG-T8801S 10G SFP+ to RJ45 Media Converter. This device is designed to convert optical signals from an SFP+ interface to electrical signals for an RJ45 Ethernet port, supporting adaptive speeds from 10Mbps to 10Gbps. It is suitable for network engineering requiring optical-to-electrical signal conversion, enhancing network transmission security and stability.

2. Key Features
- Adaptive Speed Support: RJ45 port supports 10M/100M/1G/2.5G/5G/10G full-rate, full-duplex adaptive operation.
- SFP+ Interface: Supports 1000BASE-X/2500BASE-X/10G-R optical modules.
- DIP Switch Configuration: Easy configuration of Gigabit, 2.5G, and 10G working modes via two DIP switches (B1, B2).
- Low Latency: Supports straight-through mode or store-and-forward mode with minimal delay.
- Wide Voltage Power Supply: Supports 5-15V DC power input (recommended 12V/1A-2A).
- Robust Design: IP30 protection, metal casing, natural cooling (fanless).
- Lightning Protection: Port 1 level lightning protection for enhanced durability.
3. Package Contents
Please check the package contents upon receipt. If any items are missing or damaged, contact your vendor.
- HORACO LG-T8801S 10G SFP+ to RJ45 Media Converter
- Power Adapter (EU/US/UK/AU Adapter, depending on selection)
- User Manual (this document, or refer to the User manual (PDF) for a printable version)

4. Setup and Installation
4.1. Physical Connections
- Connect Power: Connect the provided power adapter to the DC 12V input port on the media converter and then plug it into a power outlet. The 'Power' LED indicator should light up.
- Insert SFP+ Module: Carefully insert a compatible SFP+ optical module into the SFP+ port (labeled 'T1') on the media converter.
- Connect Fiber Optic Cable: Connect the fiber optic cable from your network device (e.g., switch, router) to the SFP+ module.
- Connect RJ45 Ethernet Cable: Connect a standard RJ45 Ethernet cable from your network device (e.g., computer, switch) to the RJ45 port (labeled 'R1') on the media converter.


4.2. DIP Switch Rate Adjustment
The media converter features two DIP switches (B1 and B2) on the side panel to configure the operating speed of the SFP+ interface. The RJ45 port will auto-negotiate to compatible speeds.

| DIP Switch (B1 B2) | Working Mode | Description |
|---|---|---|
| Up Up | 10G Mode | SFP interface 10G-R mode, RJ45 port 10M/100M/1G/2.5G/5G/10G adaptive. |
| Up Down | 2.5G Mode | SFP interface 2500BASE-X mode, RJ45 port 10M/100M/1G/2.5G adaptive. |
| Down Up | Gigabit Mode | SFP interface 1000BASE-X mode, RJ45 port 10M/100M/1G adaptive. |



5. Operation
5.1. LED Indicators
The front panel of the media converter features several LED indicators to provide status information:

| Indicator | Status | Description |
|---|---|---|
| POWER | On | Device is powered on. |
| link/act (SFP+) | On | SFP+ port is linked. |
| link/act (SFP+) | Flashing | Data is being transmitted/received on SFP+ port. |
| misc (SFP+) | On | Indicates specific SFP+ module status (e.g., 10G mode). |
| speed (SFP+) | On | Indicates specific SFP+ module speed (e.g., 1G, 2.5G). |
| duplex (SFP+) | On | Indicates full-duplex operation on SFP+ port. |
| link/act (RJ45) | On | RJ45 port is linked. |
| link/act (RJ45) | Flashing | Data is being transmitted/received on RJ45 port. |
| speed (RJ45) | On | Indicates specific RJ45 port speed (e.g., 1G, 2.5G, 5G, 10G). |
| duplex (RJ45) | On | Indicates full-duplex operation on RJ45 port. |
5.2. Auto-Negotiation
The RJ45 port on the LG-T8801S supports auto-negotiation, allowing it to automatically detect and adapt to the highest common speed (10M/100M/1G/2.5G/5G/10G) and duplex mode with the connected device. Ensure the connected device also supports auto-negotiation for optimal performance.
6. Maintenance
The HORACO LG-T8801S media converter is designed for reliable operation with minimal maintenance. Follow these guidelines to ensure longevity:
- Cleaning: Keep the device clean and free from dust. Use a soft, dry cloth for cleaning. Do not use liquid or aerosol cleaners.
- Environmental Conditions: Operate the device within the specified temperature (-30°C to +75°C) and humidity (5-95% non-condensing) ranges.
- Ventilation: Although fanless, ensure adequate airflow around the device to prevent heat buildup. Do not block ventilation holes.
- Cable Management: Ensure all cables are securely connected and not under strain. Avoid sharp bends in fiber optic cables.
7. Troubleshooting
If you encounter issues with your media converter, refer to the following common problems and solutions:
- No Power:
- Ensure the power adapter is securely connected to the device and a working power outlet.
- Verify the power adapter is functioning correctly.
- No Link/Activity:
- Check that the SFP+ module is correctly inserted and compatible.
- Verify that the fiber optic cable is properly connected and not damaged.
- Ensure the RJ45 Ethernet cable is securely connected to both the converter and the network device.
- Confirm that the connected network devices (switch, router, NIC) are powered on and functioning.
- Check the DIP switch settings to ensure the correct speed mode is selected for your SFP+ module and network.
- Incorrect Speed or Performance Issues:
- Verify the DIP switch settings match the desired speed for your SFP+ module.
- Ensure the connected RJ45 device supports the negotiated speed.
- Use high-quality Ethernet cables (e.g., Cat6 or higher for 2.5G/5G/10G) and SFP+ modules.
- Note on 5G: While the RJ45 port supports 5G adaptive, some specific 5G NICs may have compatibility issues, potentially resulting in lower actual speeds (e.g., ~3Gbps).
- Note on 10G Symmetrical Connections: Some users have reported instability or crashes when attempting symmetrical 10Gb connections, leading to connection loss or network card blockages. If experiencing this, consider testing with asymmetrical loads or different network configurations.
- Device Overheating:
- Ensure the device is placed in a well-ventilated area.
- Despite its low heat generation, extreme ambient temperatures can affect performance.
For more detailed troubleshooting or complex issues, please refer to the comprehensive User manual (PDF) or contact technical support.
8. Specifications

| Parameter | Value |
|---|---|
| Model Number | LG-T8801S |
| Application Layer | Physical Layer (PHY) / Store-and-Forward |
| Backplane Bandwidth | 13.125Gbps |
| Packet Forwarding Rate | 5.784Mpps |
| MAC Table Size | 8K |
| Packet Buffer | 0 |
| Latency | 12us |
| Switching Method | Straight-through / Store-and-Forward |
| Data Forwarding Fault Self-Healing | 30s |
| Transmission Distance | 0-100KM (depends on optical module parameters) |
| Transmission Mode | 10M/100M/1G/2.5G/5G/10G Adaptive |
| Indicator Lights | 6 front panel indicators (see section 5.1) |
| Interface Quantity | 1x SFP+ optical port (supports 1G/2.5G/10G optical modules), 1x 10M/100M/1G/2.5G/5G/10G adaptive RJ45 port |
| Network Protocols | IEEE 802.3i, IEEE 802.3u, IEEE 802.3z, IEEE 802.3ad, IEEE 802.3at |
| Protection Level | IP30 |
| Housing Material | Metal |
| Cooling Method | Natural cooling, fanless |
| Lightning Protection | Port 1 level lightning protection (differential mode, common mode surge suppression) |
| Operating Power | Supports 5-15V DC, recommended DC12V/1A-2A |
| Power Consumption | 2.4W @ 65°C |
| Operating Temperature | -30°C ~ +75°C |
| Operating Humidity | 5% ~ 95% (non-condensing) |
| MTBF | 100,000 hours |
| Dimensions (L*W*H) | 95 * 70 * 26mm |
| Weight | 0.198kg |
| Installation Method | Desktop, 2U14 slot rack-mounted |
| Certifications | CE, FC, RoHS |
9. User Tips
- Low Heat Generation: Users frequently report that this converter generates very little heat, contributing to its reliability and longevity.
- DIP Switch is Key: Always ensure the DIP switches are correctly set for your desired SFP+ speed (10G, 2.5G, or Gigabit) to ensure proper operation and compatibility with your network.
- Real-World Performance: While rated for 10G, actual throughput on a 10G optical line might be around 7-8Gbps depending on your network environment and connected devices.
- Cable Quality Matters: For optimal performance, especially at higher speeds (2.5G, 5G, 10G), use high-quality Ethernet cables (e.g., Cat6 or Cat6a) and compatible SFP+ modules.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your original point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.
A comprehensive user manual is available in PDF format for download: HORACO LG-T8801S User Manual (PDF).