Important Safety Information
WARNING:
Electric bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle. It is important for you to understand your new bicycle. By reading this manual before you go out on your first ride, you'll know how to get better performance, comfort, and enjoyment from your new bicycle. It is also important that your first ride on your new bicycle is taken in a controlled environment, away from cars, obstacles, and other cyclists.
- Always Wear A Helmet: Helmets significantly reduce the rate of head injuries. Always wear a helmet that complies with your state laws when riding the E-bike. Check with your local police department for requirements in your community. Make yourself more visible by wearing bright reflective clothing. Keep your reflectors clean and eye protection. Also check your state laws concerning other protective gear that may be required when riding the E-bike.
- Know Your E-bike: Your new E-bike incorporates many features and functions that have never been built into a bicycle before. Read this manual thoroughly to understand how those features enhance your riding pleasure and safety.
- Ride Within Your Limits: Take it slow until you are familiar with the riding conditions that you encounter. Be especially careful in wet conditions as traction can be greatly reduced and brakes becoming less effective. Never ride faster than conditions warrant or beyond your riding abilities. Remember that alcohol, drugs, fatigue and inattention can significantly reduce your ability to make good judgement and safely.
⚠️ Disclaimer: Please mind potential fire risk and strictly follow the instruction manual for charging and storage. While using the product, please wear protective equipment and fully comply with the applicable law and regulations.
Product Overview
Parts Identification
The ZEFIORA V10 Electric Bicycle features a robust design with clearly identifiable components. Refer to the diagram below for a visual representation of each part.

Key components include:
- Display: Mounted on the handlebar, shows operational data.
- Handlebar: For steering and control, includes power button, gear shift, and light switch.
- LED Headlight: Front illumination for visibility.
- Front Fender: Protects from splashes.
- Disc Brake Rotor: Part of the braking system.
- Tire: Fat tires for various terrains.
- Front Fork: Suspension component.
- Pedals: For manual propulsion.
- Chain: Connects crank to rear wheel.
- Crank: Connects pedals to chain.
- Battery: Power source for the motor, located on the frame.
- Derailleur: For gear shifting.
- Bike Motor: Provides electric assistance.
- Rear Fender: Protects from splashes.
- Controller: Manages electrical systems.
- Light: Rear light.
- Seat: Riding position.
- Rear Rack: For carrying items.
- Bike Frame: Main structure of the bicycle.
Specifications
The following table details the key specifications of the ZEFIORA V10 Electric Bicycle:
| Attribute | Value |
|---|---|
| Brand Name | ZEFIORA |
| Model Number | V10 |
| Voltage | 48V |
| Wattage | > 500W |
| Power Supply | Lithium Battery |
| Power Source | Lithium Battery |
| Max Speed | >50km/h |
| Range per Power | > 60 km |
| Wheel Size | 20" |
| Frame Material | Aluminum alloy |
| Motor | Brushless |
| Folded | No |
| Rated Passenger Capacity | One Seat |
| Style | Standard Type |
| Certification | CE |
| High-concerned chemical | None |
| Origin | Mainland China |
| Vehicle Size | 168 × 69 × 110 cm |
| Packing Size | 138 × 26 × 84 cm |
| Color | Black |
| Net Weight | 37 kg (81.57lb) / 36.5KG (80.47lb) |
| Gross Weight | 46kg (101.41lb) |
| Charger | AC-DC 54.6V 2A, Input: 100-240V AC, Connector: DC 5.5×2.1 mm |
| Brake System | Front and rear disc brake |
| Tire Size | 20×4.0 inch |
Assembly Instructions
The following assembly steps are only a general guide to assist in the assembly of your bike and are not a complete or comprehensive manual of all aspects of assembly, maintenance, and repair. If you are still unable to install after reading these instructions, you can contact customer service for assistance.
- Unpack E-bike: Unpack the e-bike from the carton and carefully set out all contents of the box. Remove packaging material protecting the bike frame and components. Please recycle packaging materials, especially cardboard and foam.
- Install Front Wheels: Insert the front wheel into the front fork. Next, insert the fork anti-spin hook plate and washer, and finally insert the nut and tighten it.
- Install Kickstand: Remove the kickstand, then with the kickstand on the inside and the screws on the outside, tighten them clockwise using an M6 screwdriver.
- Install Handlebars: Loosen the handlebar mounting screws, place the handlebars on, and finally tighten the screws.
- Adjust Front of Vehicle: Adjust the front of the vehicle so that it is level with the tires, and tighten the bolts on both sides.
- Install Headlight: For headlight installation, first open the headlight mounting brackets on both sides, then install the black spacers. Then tighten the screws on both sides.
- Connect Headlight Wiring: Locate the headlight wiring harness and the main wiring harness, which have arrow markings. Align them with the arrows and insert them into the harness, then confirm that they are securely plugged in.
- Install Front Fender: Remove the front fender and insert it from back to front, then tighten the screws. Then, secure the mounting brackets on both sides with screws.
- Adjust Brake Tightness: If your bicycle's disc brakes are rubbing against the disc (making a "sizzling" sound), follow these steps:
- Prepare tools and locate: Locate the disc brake caliper (the metal part that holds the brake disc). You will see two vertical screws on the caliper (usually an M6 Allen wrench is used).
- Loosen the screws: Use an M6 Allen wrench to slightly loosen these two screws (one to one and a half turns). Do not completely remove them.
- Alignment Position: Gently straighten the wheel with your hand, ensuring it's centered on the frame. Use your hand to slightly adjust the position of the brake caliper, moving it left and right. The goal is to align the brake disc exactly in the center of the two brake pads, with even clearance on both sides. While adjusting, gently rotate the wheel with your other hand, judging by the sound. The optimal position is when it rotates smoothly without any friction noise.
- Tighten screws: Keeping the caliper in the optimal position, tighten the two loosened screws alternately and in stages. Do not tighten one screw completely at once, as this can easily cause the position to shift again. After the screws are fully tightened, quickly rotate the wheel one last time to confirm that there are no abnormal noises. If there is still slight friction, repeat steps 2-3.
- Rear Rack Installation: Locate the taillight, loosen the taillight screws, and remove the taillight. Unscrew all four screws on the back. Then place the rear rack in position, align the holes, and tighten the screws on both sides.
- Taillight and Rear Seat Bag Installation: Locate the taillight wiring and tie it up with the cable ties that come with the vehicle. Place the rear seat bag as shown in the picture, then tighten the fixing screws above the rear fender.
Operation
Operation Meter
The operation meter provides essential information about your ride. It includes a display for battery level, total distance (ODO), single trip distance (TRIP), current speed, gear, and status bar. It also shows icons for boost, headlight, and NFC.
- Power On/Off: Press and hold the [Power button] for 2 seconds to turn the device on or off.
- Gear Shift: Press the [+ button] briefly to increase by one gear, and press the [- button] briefly to decrease by one gear.
- ODO/TRIP Data Display Toggle: Briefly press the [Power button] to switch between displaying ODO and TRIP data. The default display is TRIP.
- Implementation Model: Press and hold the [- button] to enter Implementation Model, and release the button to exit.
Setting Menu Operations
To access general settings: Press and hold both the [+ button] and [- button] simultaneously to enter the general settings menu.
- Switch setting items: In the settings menu, press the [Power button] briefly to toggle between options.
- Adjust setting parameters: Press the [+ button] or [- button] briefly to modify parameters.
- Confirm: Press and hold the [Power button] to save changes and return to the previous level.
- Return to home page: Press and hold the [- button] to exit without saving and return to the main interface, or remain inactive on the page for 60 seconds to automatically exit the settings menu and return to the home page.
SETTING MENU OPTIONS:
- SET 1: Wheel Diameter - Adjustable range: 16-29 inches (in inches), default: 26 inches. This setting is not adjustable by default.
- SET 2: Speed Limit - Select any value within the adjustable range (1-99), default: 25 km/h. This setting is not adjustable by default.
- SET 3: Unit - Options: Metric (KM/H) or Imperial (blank), default: KM/H.
- SET 4: Screen Brightness - Adjustable range: 1-3 levels, default: Level 3.
- SET 5: Auto Sleep Time - Adjustable range: 1-60 minutes, default: 10 minutes.
- SET 6: Single Trip Auto Reset - Options: Set to "y" to clear the single trip mileage on startup, or set to "n" to retain the single trip mileage on startup.
Gears Operation
Multi-speed bicycles can have internal or derailleur gear systems. Improper shifting can result in the chain jamming or becoming derailed, leading to loss of control or a crash. Always ensure the chain is fully engaged in the desired gear before pedaling hard.
Avoid shifting while standing up on the pedals or under load.
To shift properly, pedal the bicycle with little pressure on the pedals, and move the shifter one gear at a time, ensuring that the chain is fully engaged in that gear before applying more pressure on the pedals. For bicycles with 3 front chain rings, avoid "Cross Chaining," which is the position when the chain is in the smallest cog in the rear combined with the inner or smallest chain ring in the front, or the largest cog in the rear and the outer or largest chain ring in the front. These gear positions put the chain at the most extreme angle and can cause premature wear to the drivetrain. Bicycles with 3 front chain rings have enough gear "overlaps" that these gears are not needed.
Battery Usage and Charging
How to Use the Battery
To turn on the battery switch, insert the battery key and turn it counterclockwise. Then, remove the battery with both hands. To check the battery level, turn on the red switch on the battery power button, then press the battery power button briefly.
Charging Procedure
- Remove the rubber cover on the charging port on the opposite side of the battery from the key switch.
- With the battery on or off the bike, place the charger in a flat, secure place, and connect the DC output plug from the charger (round barrel connector) to the charging port on the side of the battery.
- Plug the charger into the outlet, then the charging port. Connect the charger input plug (100-240-volt plug) to the power outlet. Charging should initiate and will be indicated by the LED charge status light on the charger turning red.
- Unplug the charger from the outlet, then the charging port. Once fully charged, indicated by the charging indicator light turning green, unplug the charger from the wall outlet first and proceed to remove the charger.
Attention:
Before charging, make sure that the charger light faces upwards. A full charge normally takes 3-7 hours. Charge the battery in a clean and safe place and do not overcharge.
A red light on the charger means the battery is charging. A green light means the battery is fully charged.
Battery Charging Information
Always charge your battery in temperatures between 50°F - 77°F (10°C - 25°C) and ensure the battery and charger are not damaged before initiating charge. If you notice anything unusual while charging, please discontinue charging and use of the bike and contact for help. Charging the battery fully normally takes 3-7 hours. In rare cases, it may take longer to allow the battery management system to balance the battery, particularly when the bike is new or after long periods of storage.
The battery can be recharged on or off the bike.
Do not charge the battery for more than 12 hours at a time or leave a charging battery unattended.
Ensure the lights face upwards when using the charger. The charge indicator lights on the charger will stay red while the battery charges and one will turn green when charge is complete.
Always charge in dry, indoor locations away from direct sunlight, dirt, or debris. Charge in a clear area away from potential to trip on the charging cords or for damage to occur to the bike, battery, or charging equipment while parked and/or charging. Do not use with the charger inverted, which can inhibit cooling and reduce charger lifespan.
The battery should be recharged after each use, so it is ready to go the full range per charge next ride. There is no memory effect, so charging the battery after short rides will not cause damage.
Ensure the battery is turned off whenever it is being removed or off the bike. Avoid damaging the exposed connector terminals and keep them clear of debris.
Do not touch the "+" and terminal contacts on the bottom of the battery when the battery is removed from the bike.
Maintenance
Basic Bike Care
To ensure safe riding conditions, you must properly maintain your bike. Follow these basic guidelines and see a certified, reputable bike mechanic at regular intervals to ensure your bike is safe for use and fun to ride.
- Properly maintain batteries by keeping them fully charged when between uses of up to two weeks apart. See Long-Term Battery Storage section of manual for information on storing the battery for longer than two rides.
- Never immerse or submerge the bike or any components in water or liquid as the electrical system may be damaged.
- Periodically check wiring and connectors to ensure there is no damage and the connectors are secure.
- To clean, wipe the frame with a damp cloth. If needed, apply a mild non-corrosive detergent mixture to the damp cloth and wipe the frame. Dry by wiping with a clean, dry cloth.
- Store under shelter; avoid leaving the bike in the rain or exposed to corrosive materials. If exposed to rain, dry your bike afterwards and apply anti-rust treatment to chain and other unpainted steel surfaces.
- Riding on the beach or in coastal areas exposes your bike to salt, which is very corrosive. Wipe down your bike frequently and wipe or spray all unpainted parts with anti-rust treatment. Damage from corrosion is not covered under warranty so special care should be given to extend the life of your bike when used in coastal areas or areas with salty air or water.
- If the hub and bottom bracket bearings have been submerged in water or liquid, they should be taken out and re-greased. This will prevent accelerated bearing deterioration.
- If the paint has become scratched or chipped in the metal, use touch up paint to prevent rust. Clear nail polish can also be used as a preventative measure.
- Regularly clean and lubricate all moving parts, tighten components, and adjust as required.
Pre-Riding Safety Checklist
Before every ride, and after every 25-45 miles, follow this pre-riding safety checklist:
| Safety Check | Basic Steps |
|---|---|
| 1. Brakes |
|
| 2. Wheels and Tires |
|
| 3. Steering |
|
| 4. Chain |
|
| 5. Bearings |
|
| 6. Cranks and Pedals |
|
| 7. Derailleurs |
|
| 8. Frame, Fork, and Seat |
|
| 9. Motor Drive Assembly |
|
| 10. Battery |
|
| 11. Electrical Cables |
|
| 12. Accessories |
|
Your cables, spokes, and chain will stretch after an initial break-in period of 50-100 miles (80-160km), and bolted connections can loosen. Always have a certified, reputable mechanic perform on your E-bike after this initial break-in period (depending on riding conditions such as total weight, riding characteristics, and terrain). Regular inspections and tune-ups are particularly important for ensuring that your bike remains safe and fun to ride.
Troubleshooting
Fault Display
When a fault occurs, the red fault indicator on the instrument panel lights up. The instrument interface will flash the fault information as a reminder and display the "Error" prompt. Refer to the table below for fault codes:
| No. | Data Status | Meaning | Instrument Display |
|---|---|---|---|
| 1 | 0x21 | Controller Fault | 21 |
| 2 | 0x22 | Throttle Fault | 22 |
| 3 | 0x23 | Motor Phase Loss | 23 |
| 4 | 0x24 | Hall Sensor Fault | 23 |
| 5 | 0x25 | Undervoltage Protection | 25 |
| 6 | 0x26 | Brake Lever Fault | 26 |
| 7 | 0x30 | Communication Fault | 30 |
Basic Troubleshooting
If you encounter issues with your e-bike, consult the following table for common symptoms and solutions. If the problem persists, contact customer service.
| Symptoms | Possible Causes | Most Common Solutions |
|---|---|---|
| The bike does not work |
|
|
| Irregular acceleration and/or reduced top speed |
|
|
| The motor does not respond when the bike is powered on |
|
|
| Reduced range |
|
|
| The battery will not charge |
|
|
| Wheel or motor makes strange noises |
|
|
You can contact the customer service of the platform you purchased from for further assistance.
Additional Resources
User Manual PDF
For a downloadable version of the user manual, please refer to the official PDF document: ZEFIORA V10 Electric Bicycle User Manual (PDF).
Product Video
Watch the official product video for a visual guide on features and usage:
Safety Notes
The following safety notes provide additional information on the safe operation of your bike. Failure to review these notes can lead to serious injury or death.
- All users must read and understand this manual before their first use of the bike. Additional manuals for components used on the bike may also be provided and should be read before use in addition to this manual.
- Ensure that you comprehend all instruction and safety notes/warnings.
- Ensure the bike fits you properly before your first use. You may lose control or fall if your bike is too big or too small. Always wear an approved bicycle helmet whenever using this product and ensure that all helmet manufacturer instructions are used for fit and care of your helmet. Failure to wear a helmet when riding may result in serious injury or death.
- Ensure correct setup and tightening is performed on your bike before first using it and check the setup, tightening, and condition regularly. It is your responsibility to familiarize yourself with the laws and requirements of operating this product in the area(s) where you ride. Ensure the handlebar grips are undamaged and properly installed. Loose or damaged grips can cause you to lose control and fall.
- Do not use this product with standard bike trailers, stands, electric bike racks or accessories that E-bikes has not tested for safety and compatibility and have verified as safe and compatible with the bike. Contact E-bikes to check if your equipment will work with the bike. Off-road riding requires close attention, specific skills, and presents variable conditions and hazards which accompany the conditions. Wear appropriate safety gear and do not ride alone in remote areas. Check local rules and regulations if off-road E-bike riding is allowed. Engaging in extreme riding is extremely dangerous and should be avoided. Although many articles/advertisements/catalogs depict extreme riding, this is not recommended nor permitted, and you can be seriously injured or killed if you perform extreme riding.
- Bikes and bike parts have strength and integrity limitations and extreme riding should not be performed as it can damage bike components and/or cause or lead to dangerous riding situations in which you may be seriously injured or killed.
- Failure to perform and confirm proper installation, compatibility, proper operation, or maintenance of any component or accessory can result in serious injury or death.
- It is recommended to not ride at night if avoidable. Ride at night only if necessary.