1. Product Overview
1.1 Main Features
- 10 NOAA weather channels
- Multi-band transmit and 50-600MHz full-band receive
- AM/FM aviation band receive
- Cross-band communication
- Fast frequency matching
- Frequency meter function
- Wireless full-machine copy
- Emergency alarm
- FM radio
- 10 groups of voice encryption (scrambler)
- Multiple scanning modes
- Digital signaling CTCSS/DCS
- Large capacity battery / long standby time
- Call channel function
- Type-C and cradle charging
- Illumination function
- High, medium, low power selection
- VOX voice-activated transmission function
- Dual standby
- Independent receive/transmit signaling settings
- Frequency offset direction setting
- DTMF dialing
- DTMF ANI
- DTMF selective calling (individual, group, all calls)
- Power-on password protection
- Frequency inversion function
- Multiple step frequencies
- Offset frequency setting
- Busy channel lockout
- Timeout timer
- Channel number, channel frequency, channel name multiple display modes
- Wide/narrow band selection
- Initialization settings
- 1750Hz tone transmission
- Squelch level setting
- On-site programming
- Frequency, channel mode switching
- Keypad lock
- Channel scan add/remove
- 200 channels
- PC programmable
- Large screen dot matrix LCD display
- Voice prompt
- Tone switch
- Backlight auto-off time selection
- Repeater relay confirmation function
- Automatic signaling search
- Remote stun/kill, activate function
- Customizable power-on image
- Supports Chinese/English channel names
1.2 Package Contents
Carefully remove the walkie talkie from its packaging. Please check that all items listed below are present and in good condition. If any items are missing or damaged, contact your dealer immediately.
| Item | Quantity |
|---|---|
| Walkie Talkie | 1 |
| Antenna | 1 |
| Lithium Battery | 1 |
| Belt Clip | 1 |
| Battery Charger (Cradle) | 1 |
| User Manual | 1 |
Note: The product is available with two battery versions: Long battery (2500mAh) or Short battery (1400mAh). The package contents may vary slightly based on your purchased configuration.

Image: Comparison of UV-K1 with long (2500mAh) and short (1400mAh) battery versions.

Image: Charging cradle and USB cable.
1.3 Device Layout

Image: Diagram illustrating the main components of the UV-K1 walkie talkie.
- Antenna: For signal transmission and reception.
- Status Indicator: Red for transmitting, Green for receiving. Blue indicates charging (solid blue for charging, flashing blue for near full, off when fully charged).
- Flashlight: Located at the top.
- Power/Volume Knob: Rotate clockwise to turn on and increase volume; counter-clockwise to decrease volume and turn off.
- 1.44-inch Screen: Displays operational information.
- Menu/Confirm Key: Enters menu, confirms selections.
- Digital Keypad/Function Keys: For entering frequencies, channel numbers, and accessing various functions.
- PTT (Push-to-Talk) Button: Press to transmit, release to receive.
- Side Key 1 & 2: Programmable function keys (e.g., Monitor, 1750Hz, Flashlight, Emergency Alarm).
- Return/Exit Key: Returns to previous menu, exits current mode, clears input.
- Headphone/Microphone Jack: For external audio accessories.
- Type-C Charging Port: For direct charging.
1.4 LCD Display Icons
The LCD screen displays various icons to indicate the radio's status and selected functions:
| Icon | Description |
|---|---|
| Yll | Signal Strength Indicator (fewer bars indicate weaker signal) |
| HML | Transmit Power Indicator (H: High, M: Medium, L: Low) |
| CT DCS | Current Analog Sub-tone (CTCSS) or Digital Sub-code (DCS) |
| Voice Prompt Enabled | |
| N | Narrowband Mode |
| VOX | Voice Operated Transmit (VOX) enabled |
| +- | Frequency Offset (Transmit frequency = Receive frequency +/- offset) |
| DTMF | DTMF Signaling Decoding Enabled |
| DW | Dual Watch function enabled |
| Keypad Lock Icon | |
| Battery Level Indicator (flashing indicates low battery) | |
| Main Channel Indicator (all operations apply to this channel) | |
| SCR | Scrambler (Voice Encryption) enabled |
| R | Reverse Frequency Mode |
| Scanning Indicator | |
| WX | Cross-band Receive/Transmit |
| RX | Receiving |
| TX | Transmitting |
| AM | Aviation Band AM Receive |
| NS | NOAA Channel Auto Scan |
| > | Temporary Transmit Channel (sub-channel temporarily becomes transmit channel upon call) |
2. Setup
2.1 Initial Charging
The battery pack is not charged at the factory. Please charge it before use. After purchasing or long-term storage (more than two months), the battery pack may not reach its full capacity on the first charge. It will achieve normal charging efficiency and battery energy after two or three charge/discharge cycles.
Important Safety Notes:
- Do not transmit while charging, as this may damage the radio and pose a safety risk.
- Remove the battery pack from the charger once it is fully charged.
- If the battery pack's usage time does not increase even after proper charging, it indicates the battery has reached its lifespan and should be replaced.
- Only use original lithium batteries and chargers.
- Do not short-circuit the battery terminals or dispose of the battery in fire.
- Do not attempt to disassemble the battery pack casing.
Cradle Charger Instructions:
- Insert the lithium battery pack or the walkie talkie with the battery pack into the cradle charger. Ensure the battery contacts are properly aligned with the charger terminals.
- When the cradle charger is empty, the green light is on. When charging, the red light is on. When fully charged, the green light will turn on.
- Remove the battery pack from the cradle charger once fully charged.
Type-C Charging Instructions:
- Type-C charging is for emergency use only; regular charging is recommended via the cradle charger.
- Turning off the radio does not affect Type-C charging.
- During charging, the blue light is on. When charging is nearing completion, the blue light flashes, indicating low current charging.
- The blue light turns off when Type-C charging is complete.
- Do not remove the battery while using the body's Type-C charging port.

Image: UV-K1 with Type-C charging cable.
2.2 Battery and Antenna Installation
Attach the antenna by screwing it clockwise onto the connector on top of the radio until secure. Insert the battery pack into the compartment on the back of the radio, ensuring it clicks into place.
2.3 Power On/Off
Rotate the Power/Volume knob clockwise to turn on the radio. Continue rotating clockwise to increase the volume. Rotate counter-clockwise to decrease the volume and turn off the radio.
2.4 Power-on Password Protection
If a power-on password has been set via PC programming, the display will show "LOCK" upon startup. Enter the correct password using the keypad to unlock and use the radio.
2.5 Customizable Power-on Image
The UV-K1 supports a DIY power-on photo feature, allowing users to customize the image displayed when the radio powers on.

Image: UV-K1 displaying a custom power-on image.
3. Operating Instructions
3.1 Basic Operation
3.1.1 Channel/Frequency Mode Switching
From the main interface, press the F key followed by 3 to switch between Frequency (VFO) mode and Channel (MR) mode.
3.1.2 Main Channel Switching
Press the F key followed by 2 to switch between the main (A) and sub (B) channels. The solid arrow on the display indicates the currently active main channel.
3.1.3 Transmit Power Adjustment
Press the F key followed by 6 to cycle through High (H), Medium (M), and Low (L) transmit power settings. Alternatively, navigate to the TXP menu item (Menu 03) to adjust.
3.1.4 Multi-band Receiving & Transmitting
The UV-K1 supports a wide receiving frequency range of 50-600MHz and transmitting in specific bands (e.g., 144-148MHz/420-450MHz for FCC version, 144-146MHz/430-440MHz for CE version).

Image: UV-K1 displaying multi-band receiving and transmitting frequencies.
3.1.5 AM/FM Aviation Band Receiving
The radio is capable of receiving AM/FM signals in the aviation band.

Image: UV-K1 demonstrating AM/FM Aviation Band Receiving.
3.2 Advanced Features
3.2.1 Frequency Meter / Fast Copy One Channel
The UV-K1 can act as a frequency meter. Press F+4 to start fast copying a channel. The radio will scan for a strong signal and display its frequency and CTCSS/DCS codes.

Image: UV-K1 displaying frequency scanning for fast copy.
3.2.2 Wireless Copy
To enter wireless copy mode, power on the radio while holding down the PTT button and Side Key 2. The display will show "AIR COPY (RDY)". Both transmitting and receiving radios must be set to the same frequency. The receiving radio presses EXIT to enter receive mode, and the transmitting radio presses MENU to start transmitting programming data. The progress will be displayed as RCV:XX E:XX, where E:XX indicates data errors. Upon completion, the transmitting radio will show SND:120.
3.2.3 Scanning
Initiating Scan:
- Long press the * key to start or exit scanning.
- Alternatively, assign the scan function to a programmable side key.
Frequency Scan: In frequency mode, press the left/right arrow keys to change the scanning direction. Press PTT or EXIT, or long press the * key to exit scanning.
Channel Scan: In channel mode, the radio will sequentially scan channels in the scan list. If a call is received during scanning, you can respond by pressing PTT.
Scan List Management:
- MENU → 32 S-LIST: Select scan list 1 or 2.
- MENU → 33 SLIST1: View channels in scan list 1.
- MENU → 34 SLIST2: View channels in scan list 2.
- MENU → 26 S-ADD1: Add current channel to scan list 1.
- MENU → 27 S-ADD2: Add current channel to scan list 2.
- MENU → 23 SC-REV: Select scan resume mode (TO: Time Operated, CO: Carrier Operated, SE: Search End).
Priority Scan: You can designate a channel as a priority scan channel. During scanning, the radio will spend 50% of its time scanning the priority channel. If a second priority channel is set, the first priority channel's scan time will be reduced to 25%. If activity is detected on a priority channel, the radio will stop scanning and monitor that channel.
3.2.4 NOAA Weather Channel
Press F+5 to enter or exit NOAA weather channel reception. The radio has 10 built-in NOAA weather channels. The reception method can be configured via Menu 50 NOAA_S.
3.2.5 FM Radio
Press F+0 to enter FM radio mode. Use the left/right arrow keys to change frequency or stored stations. You can also manually input frequencies. The radio can store up to 20 FM stations. If a call is received or PTT is pressed, the radio will temporarily exit FM mode and return to it after the call ends.
3.2.6 VOX Function
The VOX (Voice Operated Transmit) function allows hands-free operation. When enabled, the radio will automatically transmit when it detects your voice. Press F+7 to toggle VOX on/off. The sensitivity can be adjusted via the VOX menu item (Menu 16).
3.2.7 DTMF (Dual Tone Multi-Frequency)
DTMF Dialing:
- Manual Dialing: Press and hold PTT, then dial numbers using the keypad.
- Automatic Dialing: Press the * key, enter a 3-digit number, then short press PTT to initiate a DTMF call. The radio will automatically send its own ID.
- Individual Call: Sends the target ID plus its own ID (e.g., 123*100 for user 100 calling user 123).
- Group Call: Uses a group call code instead of an individual ID. For example, if group code A is set, sending 12A can call radios with IDs 120-129.
- All Call: Sends a 3-digit group call code to call all users.
DTMF Receiving:
- Enable DTMF decoding via MENU → 44 D-DCD ON.
- When a DTMF individual ID is received, the radio will decode it, display the caller's name, and allow communication during the reset time. After the reset time, re-decoding is required.
DTMF PTT-ID: Configurable via programming software, the radio can send an uplink code when PTT is pressed and a downlink code when PTT is released.
3.2.8 Emergency Alarm
The emergency alarm is used to signal distress. It can be activated at any time, even if there is activity on the current channel. The alarm type (local sound/light, remote transmission) can be configured via programming software.
- Activate by pressing the designated emergency alarm key (programmable side key).
- Exit alarm mode by pressing any key.
- MENU → 35 AL-MOD TONE: Local sound alarm and remote signal transmission.
- MENU → 35 AL-MOD SITE: Local sound alarm only.
3.2.9 Channel Naming/Editing
In channel mode, press MENU → 13 CHNAME. Press MENU to enter, use the # key to switch input methods, and use the digital keypad to select characters. EXIT deletes the previous character. Press MENU to confirm and return to the previous menu.
3.2.10 Storing/Deleting Channels
Storing Channels: In VFO mode, set the desired receive frequency, offset direction, offset frequency, bandwidth, signaling, transmit power, DTMF, and scrambler settings. Then, press MENU → 14 MEM-CH, press MENU to enter, use the left/right arrow keys or digital keypad to select a channel number, press MENU again, and confirm with "SURE?" to store.
Deleting Channels: Press MENU → 55 DEL-CH, press MENU to enter, use the left/right arrow keys or digital keypad to select the channel number to delete, press MENU again, and confirm with "SURE?" to delete.
3.2.11 CTCSS/DCS Settings
These settings are used to filter out unwanted signals. Navigate to MENU → 4 R-DCS (Receive DCS), MENU → 5 R-CTCSS (Receive CTCSS), MENU → 6 T-DCS (Transmit DCS), and MENU → 7 T-CTCSS (Transmit CTCSS) to set the desired codes. Use the left/right arrow keys to select from the list.
3.2.12 Frequency Offset (Repeater Function)
To use a repeater, you need to set a frequency offset. Navigate to MENU → 8 SFT_D to set the offset direction (OFF, ADD, SUB) and MENU → 9 OFFSET to set the offset frequency (0-999.9999M).
3.2.13 Scrambler
The scrambler function encrypts your voice for privacy. Navigate to MENU → 11 SCR to enable or disable the scrambler and select from 10 encryption types.
3.2.14 Busy Channel Lockout (BCL)
When BCL is enabled (MENU → 12 BCL), the radio will prevent transmission if the channel is already in use, avoiding interference.
3.2.15 Keypad Lock
Long press the # key to lock or unlock the keypad. When locked, only the PTT and programmable side keys will function normally.
3.2.16 Time-out Timer (TOT)
The TOT function (MENU → 21 TOT) limits the maximum duration of a single transmission to prevent accidental long transmissions and conserve battery. It can be set from 1 to 10 minutes.
3.2.17 Voice Prompt
The voice prompt function (MENU → 22 VOICE) provides audible feedback for operations. You can select between Chinese, English, or turn it off.
3.2.18 Backlight Settings
The backlight settings (MENU → 17 ABR) allow you to control the display backlight. Options include always on, always off, or automatic turn-off after 1-5 seconds of inactivity.
4. Maintenance
4.1 General Care
- Keep the walkie talkie and all its parts and accessories out of reach of children.
- Do not attempt to disassemble the walkie talkie. Handling by non-professionals may cause damage.
- Use only original batteries and chargers to avoid damage.
- Use only the original antenna to ensure optimal communication range.
- Avoid prolonged exposure to direct sunlight or excessively hot environments.
- Keep the walkie talkie away from dusty or humid areas.
4.2 Cleaning
Do not use harsh chemicals, cleaning agents, or strong detergents to clean the walkie talkie.
4.3 Battery Care
- Do not short-circuit the battery terminals.
- Do not dispose of the battery in fire.
- Do not attempt to disassemble the battery pack casing.
5. Troubleshooting
5.1 Common Issues
- No Power: Check if the battery is properly installed and charged. Ensure the power/volume knob is turned on.
- Cannot Transmit or Receive: Verify that the antenna is securely attached. Check the frequency/channel settings. Ensure the transmit power is not set to 'Low' if trying to communicate over a long distance.
- Poor Audio Quality: Check the volume level. Ensure the microphone and speaker are not obstructed.
- Scanning Issues: If the display shows "SCAN FAIL", it means no valid signals were found. If "SCAN CMP" is displayed, a valid signal was found and scanning stopped.
5.2 Contacting Support
If you notice any unusual odors or smoke coming from the walkie talkie, immediately turn off the power, remove the battery pack, and contact your dealer for assistance.
6. Specifications
| Category | Parameter | Value |
|---|---|---|
| General | Number of Channels | 200 |
| FM Radio Stations | 20 | |
| NOAA Channels | 10 | |
| Frequency Stability | ±1ppm | |
| Modulation Type | FM: 11KΦF3E (12.5KHz), 16KΦF3E (25KHz) | |
| Dimensions (H×W×D) | 98mm×59mm×33.8mm (Standard Battery) 120.3mm×59mm×35.8mm (Large Capacity Battery) | |
| Weight | 190g (Standard Battery) 260g (Large Capacity Battery) | |
| Environment | Operating Temperature | -20°C to +60°C |
| Antenna Impedance | 50Ω | |
| Receiver | Reference Sensitivity (FM) | F1(50-76MHz): -121dBm F2(108-135.9975MHz): -121dBm F3(136-173.9975MHz): -123dBm F4(174-349.9975MHz): -123dBm F5(350-399.9975MHz): -123dBm F6(400-469.9975MHz): -123dBm F7(470-599.9975MHz): -121dBm |
| Audio Power | ≥0.5W | |
| Audio Distortion | ≤10% | |
| Transmitter | Frequency Bands | 144-148MHz, 430-440MHz |
| Output Power | ≤5W | |
| Transmit Current | ≤1.5A | |
| Max Frequency Deviation | ≤5KHz (25KHz), ≤2.5KHz (12.5KHz) | |
| Modulation Distortion | ≤5% | |
| Spurious Radiation | ≤7.5uW | |
| Adjacent Channel Power | 70dB (25KHz), 60dB (12.5KHz) |
Note: Specifications are subject to change due to technical improvements without prior notice.
7. Warranty and Support
7.1 Warranty Information
This warranty card serves as your proof of purchase and warranty. Please keep it safe.
- The main unit is covered by a 12-month warranty from the date of purchase.
- Batteries and chargers are covered by a 6-month warranty.
- Accessories such as antennas, belt clips, car chargers, and programming cables are considered consumables and are not covered under warranty.
- The warranty card must be stamped by the seller and include the purchase date to be valid.
- Ensure the serial number on the warranty card matches the product. Alterations to the warranty card will void the warranty.
For detailed warranty terms and conditions, please refer to the official user manual PDF: Quansheng UV-K1 User Manual (PDF).
7.2 Service Options
For repair services, you may choose one of the following options:
- Contact your original point of purchase.
- Visit an authorized service center.
8. User Tips
- Custom Firmware: For advanced users, exploring custom firmware (e.g., F4HWN firmware) can unlock additional features and enhance performance.
- Battery Life: The UV-K1 is noted for its long battery life, especially with the 2500mAh option. Ensure proper charging practices to maximize battery longevity.
- Keyboard Usability: Some users find the keyboard letters slightly small. Take care when inputting frequencies or channel names.
- Reception: While a capable radio, some users have noted that its reception might be slightly less sensitive compared to larger models like the UV-K5.