BOAYAL P80

Contents

BOAYAL Portable Laser Distance Meter User Manual

Model: P80

1. Introduction

Thank you for choosing the BOAYAL Laser Distance Meter. This manual provides detailed instructions for the safe and effective use of your device. Please read it carefully before operation to prevent damage to the instrument or injury to yourself or others. Keep this manual for future reference.

BOAYAL Laser Distance Meter showing optical lens, millimeter accuracy, multiple modes, and lithium charge
Figure 1: BOAYAL Laser Distance Meter highlighting key features.

2. Safety Instructions

To ensure safe operation and prevent potential hazards, please adhere to the following safety guidelines:

  • The laser distance meter is a Class 2 laser product. Avoid looking directly into the laser beam at any time.
  • Do not direct the instrument towards the sun.
  • Do not use the device in inflammable or explosive environments.
  • Do not attempt to disassemble or repair this instrument yourself.
  • This device is not a toy; children should not use the laser distance meter.
  • Avoid using this product in unstable situations where it might fall or be damaged.
  • Do not store the instrument in high temperature or high humidity environments for extended periods.
  • Keep the surface of the instrument clean. Wipe with a wet soft cloth; do not use corrosive liquids.
  • If you encounter any quality issues or have questions, contact your local dealer or the manufacturer for assistance.

3. Product Overview

3.1. Device Components

Front and side view of the Laser Distance Meter, illustrating the dual-switch design
Figure 2: Front and side view of the Laser Distance Meter, illustrating the dual-switch design.

The BOAYAL P80 Laser Distance Meter features a compact design with intuitive controls. It includes a dual-switch design for convenient operation from both the front and the side of the instrument.

3.2. Display Symbol Indication

Table 1: Display Symbols
SymbolIndication
Battery capacity iconBattery capacity level
Area/volume iconIndicates Area or Volume measurement mode
Laser Indication iconLaser beam is active
Fore Basis iconMeasurement taken from the front of the device
Back Basis iconMeasurement taken from the rear of the device
MAX/MIN iconMaximum/Minimum value in continuous measurement
Historical Data iconIndicates historical data record
Measuring Unit (m/in/ft)Current unit of measurement

4. Setup

4.1. Battery Installation

The device requires 2 AAA alkaline batteries (not rechargeable). Follow these steps to install or replace batteries:

  1. Remove the battery compartment lid.
  2. Insert or change 2 AAA batteries, ensuring correct polarity as indicated inside the compartment.
  3. Install the battery and close the lid tightly.

Note: Do not mix old and new batteries. Replace batteries promptly when the low power indicator appears. If the instrument will not be used for a long time, remove the batteries to prevent leakage and damage.

5. Operation

5.1. Power On/Off

  • To Power On: Short press the Power button/Measurement button to turn on the instrument. It will automatically enter single measurement mode, and the laser point will activate.
  • To Power Off: Long press the Power button/Measurement button to shut down the device. The device also features an auto-off function after 180 seconds of inactivity.

5.2. Switching Measurement Basis (Fore/Back)

The device can measure from its front edge (Fore Basis) or its rear edge (Back Basis). This is useful for different measurement scenarios.

  • Short press the Function Mode switch/Shut-down button five times. The screen will display "REF".
  • Press the Function Mode switch/Shut-down button again to toggle between "Fore Basis" (measurement from the front) and "Back Basis" (measurement from the rear).
Diagram showing Fore Basis and Back Basis measurement
Figure 3: Illustration of Fore Basis (starting from the front end) and Back Basis (starting from the tail end) measurement.

5.3. Unit Switching

The device supports measurement in meters (m), feet (ft), and inches (in).

  • Short press the Function Mode switch/Shut-down button six times to enter the unit switching mode.
  • Press the Function Mode switch/Shut-down button again to cycle through the available units (m, ft, in).

6. Measurement Modes

Icons representing various measurement modes: Single, Continuous, MAX/MIN, Area, Pythagorean, Volume
Figure 4: Overview of available measurement modes.

6.1. Single Measurement

This is the default mode upon power-on.

  1. Ensure the laser point is active (if not, short press the Power button/Measurement button).
  2. Aim the laser point at the target.
  3. Short press the Power button/Measurement button again to trigger a single measurement. The result will be displayed immediately.

6.2. Continuous Measurement (Tracking)

This mode allows for dynamic measurement, displaying real-time distance updates, as well as maximum and minimum values.

  • In measurement state, long press the Power button/Measurement button to activate continuous measurement.
  • The continuous measurement identifier will appear on the display. The screen will show MIN (minimum value), MAX (maximum value), and the current real-time distance.
  • To exit, short press the Power button/Measurement button again.

6.3. Area Measurement

To calculate the area of a surface:

  1. Short press the Function Mode switch/Shut-down button once to enter area measurement mode.
  2. Measure the length by pressing the Power button/Measurement button.
  3. Measure the width by pressing the Power button/Measurement button again.
  4. The device will automatically calculate and display the area.

6.4. Volume Measurement

To calculate the volume of a space:

  1. Short press the Function Mode switch/Shut-down button twice to enter volume measurement mode.
  2. Measure the length, width, and height sequentially by pressing the Power button/Measurement button for each dimension.
  3. The device will automatically calculate and display the volume.

6.5. Pythagorean Theorem Measurement

This mode is used to calculate indirect distances (e.g., height) using the Pythagorean theorem.

  1. Short press the Function Mode switch/Shut-down button three times to enter Pythagorean theorem measurement mode.
  2. Measure the hypotenuse (c) by pressing the Power button/Measurement button.
  3. Measure one leg (b) by pressing the Power button/Measurement button again.
  4. The device will automatically calculate and display the other leg (a) or height.

7. Data Management

7.1. Data Query Function

The device can store up to 30 groups of historical measurement data.

  • Short press the Function Mode switch/Shut-down button four times to enter the data query mode.
  • Press the Function Mode switch/Shut-down button again to scroll through the stored data groups.
Image showing data storage of 30 groups on the laser distance meter
Figure 5: The device stores up to 30 groups of measurement data.

8. Maintenance

  • Keep the instrument's surface clean. Wipe it with a wet soft cloth. Do not use corrosive liquids.
  • If the device will not be used for an extended period, remove the batteries to prevent leakage and damage.
  • Store the device in a cool, dry place, away from direct sunlight and extreme temperatures.
  • Recycle waste batteries according to national or local regulations.

9. Troubleshooting

If you encounter any issues, refer to the table below for common error codes and solutions:

Table 2: Error Codes and Solutions
Error CodeIndicationSolution
Err10Low batteryReplace the batteries.
Err26Miscalculation / Out of display rangeEnsure measurements are within the device's range and follow instructions carefully.
Err15Out of rangeMeasure the target within the specified distance range of the device.
Err16Body shaking / Incorrect signalImprove measurement conditions: ensure stable hand, increase target reflectivity, reduce ambient light, or adjust distance to target.

10. Specifications

Table 3: Technical Specifications
FeatureSpecification
Brand NameINORM (BOAYAL)
Model NumberP80
Measuring Range0.164 - 262 ft (0.05 - 80m)
Measurement Accuracy±1/16in (±2mm)
Laser Type620-690nm
Laser Hazard LevelClass 2 (<1mW)
Power TypeBattery-Powered
Battery Type2 x 1.5V AAA Alkaline Batteries
Batteries IncludedYes
Measured Times (Full Power)>5000
Laser Auto On/Off30 seconds
Auto On/Off (Device)180 seconds
Historical Data Record30 groups
Distance Unitm / ft / in
Area Unitm² / ft²
Volume Unitm³ / ft³
Operating Temperature0°C ~ +40°C (32°F ~ 104°F)
Storage Temperature-20°C ~ +65°C (-4°F ~ 149°F)
Size (L x W x H)101 x 42 x 26 mm
Weight (Without battery)Approx. 72g
CertificationCE, FCC, RoHS
OriginMainland China

Note: For different measurement targets and environments, the range and accuracy may be affected. The stated accuracy is based on factory test environments meeting industry standards.

11. User Tips

  • For best accuracy, ensure the measurement surface is flat and perpendicular to the laser beam.
  • When measuring long distances or in bright sunlight, using a reflective target plate can improve accuracy.
  • Always double-check your measurement basis (Fore or Back) before taking critical measurements.
  • Utilize the continuous measurement mode for quickly finding maximum or minimum distances, such as when positioning objects.

12. Warranty and Support

12.1. Warranty Information

This product comes with a one-year warranty from the date of purchase. To claim warranty service, the warranty card and invoice must be provided.

12.2. Warranty Exclusions

The warranty does not cover:

  • Unauthorized disassembly of the instrument.
  • Damage caused by incorrect operation or human error.
  • Damage resulting from not using original accessories.
  • Repairs performed by unauthorized personnel or service centers.
  • Products with altered or deleted serial numbers.

12.3. Support

For repair, replacement, or any questions regarding the instrument, please contact your local dealer or the manufacturer directly. You can also refer to the official user manual PDF for more details: User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.